Comelit IPFCAMA06FA User manual

FISH-EYE IP CAMERAS
ART. IPFCAMA06FA
Please read this manual thoroughly before use and keep it for future reference

WARNING
This product is intended to be supplied by a Listed Power Unit, marked with
'Limited Power Source', 'LPS' on unit, output rated minimum 12VDC/2 A or POE
48VDC/ 350mA or 24VAC (depending on models), no more than 2000m altitude
of operation and Tma= 60°C.
Do not attempt to disassemble the camera; in order to prevent electric shock, do
not remove screws or covers.
There are no user-serviceable parts inside. Please contact the nearest service
center as soon as possible if there is any failure.
Avoid incorrect operation, shock vibration, heavy pressing which can cause
damage to product.
Do not use corrosive detergent to clean main body of the camera. If necessary,
please use soft dry cloth; for hard contamination, use neutral detergent.
Avoid aiming the camera directly towards extremely bright objects, such as sun,
because this may damage the image sensor.
Please follow the instructions to install the camera.
Do not operate if temperature, humidity and power supply are beyond the limits.
Keep away from heat sources such as radiators, heat registers, etc.
Do not expose the product to the direct airflow from air conditioner.
This manual is for using and managing the product. We reserve the rights of
amending the errors, software upgrades and product improvements,
interpretation and modification. These changes will be published in the latest
version without special notification.
All pictures, charts, images in this manual are only for description and
explanation of our products. The ownerships of trademarks, logos and other
intellectual properties related to Microsoft, Apple and Google belong to the
above-mentioned companies.
The instruction is for guidance only. Detailed information is in accordance
with the product.
Screenshots used in the instruction are only for indications and
explanations.
Some features are only available on certain camera models.
This manual is suitable for network fisheye camera.

Table of Contents
1Network connection.....................................Errore. Il segnalibro non è definito.
1.1 LAN.............................................................................................................1
1.1.1 Access through Comelit Advance IP Tool.......................................1
1.1.2 Access through Internet Explorer...................................................3
1.2 WAN ...........................................................................................................4
2Live View............................................................................................................7
3Network camera configuration....................Errore. Il segnalibro non è definito.
3.1 System Configuration ...............................................................................11
3.1.1 Basic Information..........................................................................11
3.1.2 Date and Time..............................................................................11
3.1.3 Local Configuration ......................................................................12
3.1.4 Storage.........................................................................................12
3.1.5 Fisheye Parameters.....................................................................12
3.2 Image Configuration .................................................................................15
3.2.1 Display Configuration...................................................................15
3.2.2 Video / Audio Configuration..........................................................16
3.2.3 OSD Configuration.......................................................................17
3.2.4 Video Mask ..................................................................................18
3.2.5 ROI Configuration.........................................................................19
3.3 PTZ Configuration.....................................................................................19
3.4 Alarm Configuration..................................................................................20
3.4.1 Motion Detection ..........................................................................20
3.4.2 Alarm In........................................................................................22
3.4.3 Alarm Out.....................................................................................22
3.4.4 Alarm Server................................................................................24
3.5 Network Configuration ..............................................................................24
3.5.1 TCP/IP..........................................................................................24
3.5.2 Port...............................................................................................25
3.5.3 Server Configuration ....................................................................25
3.5.4 DDNS...........................................................................................26
3.5.5 SNMP...........................................................................................26
3.5.6 802.1x......................................................................................................... 26
3.5.7 RTSP............................................................................................28
3.5.8 UPNP...........................................................................................28
3.5.9 Email............................................................................................29
3.5.10 FTP ..............................................................................................30
3.5.11 HTTPS .........................................................................................30
3.5.12 P2P (optional)...............................................................................30
3.5.13 QoS..............................................................................................30
3.6 Security Configuration ..............................................................................32

3.6.1 User Configuration .......................................................................32
3.6.2 Online User..................................................................................34
3.6.3 Block and Allow Lists....................................................................34
3.6.4 Security Management ..................................................................34
3.7 Maintenance Configuration.......................................................................35
3.7.1 Backup and Restore.....................................................................35
3.7.2 Reboot..........................................................................................35
3.7.3 Upgrade .......................................................................................35
3.7.4 Operation Log ..............................................................................36
4Search..............................................................................................................37
4.1 Image search.................................... Errore. Il segnalibro non è definito.
4.2 Video search.............................................................................................38
4.2.1 Local Video Search......................................................................38
4.2.2 Micro-SD card video search.........................................................40
Appendix..................................................................................................................42
Troubleshooting ......................................................................................................42

1
1 Network connection
Connect the IP Camera (IPC) via LAN or WAN through Internet Explorer browser.
1.1 LAN
In LAN, there are two ways to access IPC: 1. through the software Comelit Advance
IP Tool; 2. through Internet Explorer browser.
1.1.1 Access through Comelit Advance IP Tool
Network connection:
①Make sure the PC and IPC are connected to the LAN and the Comelit Advance IP
Tool is installed in the PC.
②Double click the Comelit Advance IP Tool icon on the desktop to run this software
as shown below:
③Modify the IP address. The default IP address of the camera is 192.168.1.150.
Click the information of the camera listed in the above table to show the network
information on the right hand. Modify the IP address and gateway of the camera and
make sure that its network address is in the same local network segment as the
computer’s

2
For example, the IP address of your computer is 192.168.1.4. Therefore, the IP
address of the camera shall be changed to 192.168.1.X. After modification, please
enter the password of the administrator and click the “Modify” button to modify the
setting.

④Double click on the IP address and the system will pop up the IE browser to
connect the IPC. Follow instructions to download, install and run the ActiveX control.
Enter the username and password in the login window.

The default Password of the administrator is admin.
The default Username is admin; the default Password is
admin.

3
The system will pop up the above textbox to ask you to change the default password.
It is strongly recommended to change the default password for account security. If “Do
not show again” is checked, the textbox will not appear the next time
1.1.2 Access through Internet Explorer
The default network settings are shown below:
IP address: 192.168.1.150
Subnet Mask: 255.255.255.0
Gateway: 192.168.1.1
HTTP: 80
Data port: 9008
Use the above default settings when logging in the camera for the first time. Connect
the camera to the computer directly through network cable.
①Manually set the IP address of the PC, the network segment should be the same
as the default settings of the IP camera. Open the network and share center. Click
“Local Area Connection” to pop up the following window:

4
Select “Properties” and then select internet protocol (for example: IPv4). Next, click
the “Properties” button to set the network of the PC.
②Open the IE browser, enter the default address of the IPC and confirm.
③Follow instructions to download and install theActiveX control.
④Enter the default username and password in the login window and then enter to
Live view.
1.2 WAN
Access through the router or virtual server

5
①Make sure the camera is connected to the local network and then log in the
camera via LAN and go to ConfigNetworkPort menu to set the port number.
Port Setup
②Go to Config NetworkTCP/IP menu to modify the IP address.
IP Setup
③Go to the router’s management interface through Internet Explorer browser to
forward the IP address and port of the camera in the “Virtual Server”.
Router Setup
④Open the Internet Explorer browser and enter its WAN IP and http port to access.
(for example, if the http port is changed to 81, please enter “192.198.1.150:81” in the
address bar of web browser to access).

6
Access through PPPoE dial-up
Network connection
Access the camera through PPPoE auto dial-up. The setup steps are as follow:
①Go to ConfigNetworkPort menu to set the port number.
②Go to Config NetworkTCP/IPPPPoE Config menu. Enable PPPoE and then
enter the user name and password from your internet service provider.
③Go to Config NetworkDDNS menu. Before configuring the DDNS, please
apply for a domain name first. Please refer to DDNS configuration for detail
information.
④Open the IE browser and enter the domain name and http port to access.
Access through static IP
Network connection
The setup steps are as follow:
①Go to ConfigNetworkPort menu to set the port number.
②Go to Config NetworkTCP/IP menu to set the IP address. Check “Use the
following IP address” and then enter the static IP address and other parameters.
③Open the Internet Explorer browser and enter its WAN IP and http port to access.

7
2 Live View
After you log in, you will see the following window. Before you view the live image,
please set the stream mode and installation method as required (see Set Fisheye
Parameters for details).
The following table is the instructions of the icons on the live view interface.
Icon
Description
Icon
Description
Select live preview
mode
Snap
Original size
Start/stop recording
Appropriate size
PTZ control
Auto
Sensor alarm indicator icon
Full screen
Motion alarm indicator icon
Start/stop live view
Zoom in
Start/stop two-way
audio
Zoom out
Enable/disable audio
In full screen mode, double click to exit.
Click to select the live view mode.
Fisheye view mode: See the picture as shown above.

8
Panoramic view mode
Fisheye+ 3PTZ view mode

9
Panoramic + 3PTZ view mode
4PTZ view mode (you need to switch the stream mode in Config System 
Fisheye Parameter interface)
In panoramic + 3PTZ view mode or fisheye + 3PTZ view mode or 4PTZ view mode,
select a PTZ window and view the image from every direction by the PTZ panel.
Click to display the control panel. The descriptions of the control panel are as
follows:

10
Select the Preset and click to call it. Select and set the Preset, then click to
save the position of the Preset. Select the Preset and click to delete it.
Select Cruise (Tour) and click to set it, add the Presets. Click to start the
Cruise (Tour); click to stop it.
Icon
Description
Icon
Description
Click it to rotate the camera
image diagonally up-left
Click it to rotate the camera
image diagonally up-right.
Click it to rotate the
camera image upwards.
Click it to stop rotating the
camera.
Click it to rotate the
camera image towards left
Click it to rotate the camera
image towards right.
Click it to rotate the
camera image diagonally
down-left
Click it to rotate the camera
image down-right.
Click it to rotate the
camera image downwards.
Drag the scroll bar to adjust
rotating speed of the camera.
Click it to zoom out the live
image.
Click it to zoom in the live
image.
Automatic Cruise (Tour)
Preset
Create and call Cruise
(Tour)

11
3 Network camera configuration
In the client, choose “Config” to go to the configuration interface.
Note: click the “Save” button to save the settings
3.1 System Configuration
3.1.1 Basic Information
In the “Basic Information” interface, the information of the device are listed.
3.1.2 Date and Time
Go to ConfigSystemDate and Time. Please refer to the following interface.
Select the time zone and DST as required.
Click the “Date and Time” tab to set the time mode.

12
3.1.3 Local Configuration
Go to ConfigSystemLocal Config to set up the storage path of captured pictures
and recorded videos on the local PC. There is also an option to enable or disable the
bitrate display in the recorded files.
3.1.4 Storage
Go to ConfigSystemStorage to go to the interface as shown below.
Micro-SD card management
Click the “Format” button to format the micro-SD card. All data will be erased by
clicking this button.
Click the “Eject” button to stop writing data to micro-SD card. Then the micro-SD card
can be removed safely.
Snapshot Quota: set the capacity of captured pictures on the micro-SD card.

13
Video Quota: set the capacity of record files on the micro-SD card.
Schedule Recording Settings
1. Go to ConfigSystemStorageRecord to go to the interface as shown below.
2. Set record stream, pre-record time, cycle writing.
Pre Record Time: set the time to record before the event recording begins.
3. Enable schedule record. Check “Enable Schedule Record” and set the schedule.
Weekly schedule
Set the alarm record time from Monday to Sunday for a single week. Each day is
divided in one hour. Green means scheduled. Blank means unscheduled.
“Add”: add the schedule for a specific day. Drag the mouse to set the time on the
timeline.
“Erase”: delete the schedule. Drag the mouse to delete the time on the timeline.
Manual Input: click it on a specific day to enter specific start and end time.

14
Holiday schedule
Set the alarm record time for a specific day, such as a holiday.
Note: Holiday schedule takes priority over weekly schedule.
Snapshot settings
Go to ConfigSystemStorageSnapshot to go to the interface as shown below.
Set the format, resolution and quality of the image saved on the micro-SD card, the
snapshot interval and quantity and the timing snapshot here.
Snapshot Quantity: is the maximum quantity of snapshots. The actual quantity of
snapshots may be less than this number. Supposing the occurrence time of an alarm
event is less than the time of capturing pictures, the actual quantity of snapshots is
less than the set quantity of snapshots.
Enable Timing Snapshot: enable timing snapshot first and then set the snapshot
interval and schedule. The setup steps of schedule are the same as the schedule
recording.
3.1.5 Fisheye Parameters
Go to ConfigSystemFisheye Parameters menu to set the stream mode and
installation method.

15
Stream mode: Fisheye + Panoramic view + 3PTZ or Fisheye or 4PTZ.
Installation method:wall, ceiling or desktop.
3.2 Image Configuration
Image Configuration includes Display, Video/Audio, OSD, Video Mask and ROI
Config. The lens control function is available for the models with motorized zoom lens.
3.2.1 Display Configuration
Go to ImageDisplay settings interface as shown below. The picture’s brightness,
contrast, hue and saturation and so on can be set here.
Brightness: set the brightness level.
Contrast: set the contrast.
Hue: set the hue.
Saturation: set the saturation.
Sharpness: set the sharpness.
Noise Reduction: decrease the noise to make the image more thorough. Increasing
the value will make the noise reduction effect better but it will reduce the image
resolution.

16
Backlight Compensation (BLC):
Off: disables the backlight compensation function (default).
HWDR: WDR can adjust the camera to provide a better image when there are
both very bright and very dark areas simultaneously in the field of the view by lowering
the brightness of the bright area and increasing the brightness of the dark area.
Recording will be stopped for a few seconds while the mode is changing from
non-WDR to WDR mode.
HLC: lowers the brightness of the entire image by suppressing the brightness of
the image’s bright area and reducing the size of the halo area.
BLC: if enabled, the auto exposure will activate according to the scene so that the
object of the image in the darkest area will be seen clearly.
Antiflicker:
Off: disables the anti-flicker function. This is used in outdoor installations.
50Hz: reduces flicker in 50Hz lighting conditions.
60Hz: reduces flicker in 60Hz lighting conditions.
White Balance: adjust the color temperature according to the environment
automatically.
Frequency: 50Hz or 60Hz.
Day/Night Mode: choose “Auto”, “Day”, “Night” or “Timing”.
Sensitivity: high, middle or low.
Infra-red Mode: choose “Auto”, “ON” or “Off”.
Exposure Mode: choose “Auto” or “Manual”. If manual is chosen, the digital shutter
speed can be adjusted.
3.2.2 Video / Audio Configuration
Go to ImageVideo / Audio interface as shown below. In this interface, set the
resolution, frame rate, bitrate type, video quality and so on.
Click the “Audio” tab to go to the interface as shown below.
You can select streams for different channels.