Comelit AHCAM727A User manual

FULL-HD
DOME CAMERA
ART.AHCAM727A
Please read this guide thoroughly before use and keep it handy for futurereference.

2
FCC COMPLIANCE STATEMENT
CE COMPLIANCE STATEMENT
CAUTION : Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
WARNING : This is a Class A product. In a domestic environment this product may cause
radio interference in which case the user may be required to take adequate measures.
FCC INFORMATION : This equipment has been tested and found to comply with the limits
for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the user
will be required to correct the interference at his own expense.

1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5.. Do not block any ventilat ion openings. Install in accord ance with the manufacturer`s
instructions.
6. Do not install near any heat sources such as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce heat.
7. Only use attachments/accessories specified by the manufacturer.
8. Use only with the ca rt, stand, tripod, bracket, or table specified by
the manufacturer, or sold with the apparatus. When a cart is used,
use caution when moving the cart/apparatus combination to avoid
injury from tip-over.
9. CAUTION - THESE SERVICING IN STRUCTIONS ARE FOR USE BY
QUALIFIED SERVICE PERSONNEL ONLY. TO REDUCE THE RISK OF
ELECTRIC SHOCK DO NOT PERFORM ANY SERVICING OTHER THAN
THAT CONTAINED IN THE OPERATING INSTRUCTIONS UNLESS YOU
ARE QUALIFIED TO DO SO.
10. Use satisfy clause 2.5 of IEC60950-1/UL 60950-1 or Certified/Listed Class 2
power source only.
11. Indoor use only.
EXPLANATION OF GRAPHICAL SYMBOLS
IMPORTANT SAFETY INSTRUCTIONS
3

4
5
6
7
8
18
18
18
STRUCTURE OF THE SETUP MENU
CONTENTS & PACKAGE 6
BASE INSTALLATION
VIDEO OUT CHECK
LENS ADJUSTMENT
DC AUTO IRIS LENS
19
SPECIFICATIONS
20
SPECIFICATIONS

5
The 1/2.8" 2.4M HD CMOS camera, especially for closed circuit television
CCTV and
security surveillance application.
1/2.8"
24 EA, 850nm IR LED
Auto and manual white balance modes (ATW/AWC/Manual/AWB)
3
HSBLC
DWDR
4
BLC (Back-light compensation)
25/30 fps @ 1080p

6
(IR Model 5 Watts)
Switch Cable : -Green & Black : open -> AHD signal BNC output
-Green & Black : short -> CVBS signal BNC output
BNC connector used to connect the camera to a DVR, etc.

7
1. Make mounting holes and cable hole in
the place (ceiling or wall) to which this
dome camera is installed using the
Drilling guide label.
2. Drill the mounting location, using the Drillng guide.
3. Attach the housing to the ceiling using
suitable fasteners, PTS1 5x30 screws
are supplied only use if they are suitable.
4. Tighten a mounting screws.
Press here to adjust the angle.
PTS1 5x30 <4X>
PT-Plug

WHITE BAL
BACKLIGHT
SENS-UP
D-WDR
<WHITE BAL>
OFF
BLC
HSBLC
<BACKLIGHT>
ATW
AWC->SET
INDOOR
OUTDOOR
MANUAL
AWB
<DAY&NIGHT>
SHARPNESS
LSC
D-EFFECT
RETURN
CAM TITLE
MONITOR
VIDEO OUT
LANGUAGE
COMET
RETURN
<EXIT>
SAVE& END
RESET
DEFECT DET NOT SAVE
9

10
MAIN MANU
LENS
EXPOSURE
BACK LIGHT
WHITE BAL
DAY&NIGHT
IMAGE
FUNCTION
SYSTEM
EXIT
DC
OFF
ATW
AUTO
SAVE&END
MAIN MANU
LENS
EXPOSURE
BACK LIGHT
WHITE BAL
DAY&NIGHT
IMAGE
FUNCTION
SYSTEM
EXIT
MANUAL
OFF
ATW
AUTO
SAVE&END
1)
2)
< EXPOSURE > MODE
1/50000, x2 ~ x30
Adjust the Auto Gain Control level. ▶ 0 - 15
AGC
3) SENS-UP Select the Digital Slow Shutter level. ▶ OFF, AUTO (x2 ~ x30)
BRIGHTNESS Adjust the BRIGHTNESS level. ▶ 0 - 100
D-WDR
DEFOG
Select the Digital WDR.▶ AUTO, ON(level 0~8), OFF
AUTO, OFF
POS/SIZE
GRADATION
DEFAULT
Adjust the window position & size
▶ 0~2
Initialize the setting values
SHUTTER
AGC
SENS-UP
BRIGHTNESS
D-WDR
DEFOG
RETURN
AUTO
|▪▪▪l▪| 11
AUTO
|▪▪l▪▪| 48
OFF
OFF
RET
MAIN MANU
LENS
EXPOSURE
BACK LIGHT
WHITE BAL
DAY&NIGHT
IMAGE
FUNCTION
SYSTEM
EXIT
DC
OFF
ATW
AUTO
SAVE&END
The EXPOSURE menu is used to set the automatic light control method for the camera.
It provides the ability to adjust the SHUTTER speed, AGC, SENS-UP, BRIGHTNESS, D-WDR,
and DEFOG functions of the camera.
Select the DC iris speed ▶ 0~15
▶ INDOOR, OUTDOOR

11
BACKLIGHT
The BACKLIGHT menu is used to the ability to prevent back lighting from the image.
1)BLC Prevents such a back light effect to secure a clear image under All illumination
environments.
Adjust the size of Back Light Compensation area.
2)HSBLC Mask the high light zone with specific color & level.
Adjust the window position & sizeAREA
Initialize the setting valuesDEFAULT
Select the HSBLC area ▶ AREA1 - AREA4SELECT
Adjust the HSBLC area window position & sizeDISPLAY
Select the HSBLC level ▶ 0 ~ 100LEVEL
All Day, NightMODE
Initialize the setting values.DEFAULT
HLBLC
SELECT
DISPLAY
BLACK MASK
LEVEL
MODE
DEFAULT
RETURN
AREA
ON
ON
|▪▪l▪▪| 30
ALL DAY
RET
< BACKLIGHT >
BLC
LEVEL
AREA
DEFAULT
RETURN
MIDDLE
RET
Select the BLC gain ▶ Low, Middle, HighLEVEL
Select the BLACK MASK ▶ ON, OFFBLACK MASK
MAIN MANU
LENS
EXPOSURE
BACK LIGHT
WHITE BAL
DAY&NIGHT
IMAGE
FUNCTION
SYSTEM
EXIT
DC
OFF
ATW
AUTO
SAVE&END