Comfortflame Rochester STDMN User manual
RochesterSTDMN
RochesterSTDMP
RochesterPFDMN
RochesterPFDMP
- Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any
other appliance.
- WHAT TO DO IF YOU SMELL GAS
any phone in your building.
-
-
tions.
fire department.
- Installation and service must be performed by
supplier.
WARNING:
FIRE OR EXPLOSION HAZARD
AVERTISSEMENT:
RISQUED’INDENDIE OU D’EXPLOSION
Le non-respect Des avertissements de sécurité
ou des dommages matériels.
- Ne pas entreposer ni utilizer d’essence ni d’autres
vapeursouliquidesinflammablesdanslevoisinage
de cet appareil ou de tout autre appareil.
- QUE FAIRE SI VOUS SENTEZ UNE ODEUR DE GAZ:
des téléphones se trouvant dans le bâtiment où
vous trouvez.
gaz depuis un voisin. Suivez les instructions du
fournisseur.
appelez le service des incindies.
- L’installationetl’entretiendoiventêtreassuréspar
un installateur ou un service d’entretien qualifié
ou par le fournisseur de gaz.
CONSUMER: Retain this manual for future
reference.
Installateur : Laissez cette notice avec l’appareil.
Consommateur : Conservez cette notice pour
consultation ultérieure.
is used.
Installation and Operation Instructions
Models
PFS
®
USC
Report No. F14-165
Ce manuel est disponible en francais, simplement
en faire la demande. Numéro de la pièce 900476-01.
P/N 900476-00 Rev. NC 08/2015
RochesterTM See-Through and Peninsula Direct-Vent
Gas Fireplaces
WELCOME HOME TO WARMTH
TM
P900476-00
2
DANGER
HOT GLASS WILL
CAUSE BURNS.
DO NOT TOUCH GLASS
UNTIL COOLED.
NEVER ALLOW CHILDREN
TO TOUCH GLASS.
-
other at-risk individuals.
DANGER
PELIGRO
VITRE CHAUDE
RISQUE DE BRÛLURES.
NE TOUCHEZ PAS UNE VITRE
NON REFROIDIE.
NE LAISSEZ JAMAIS UN ENFANT
DE TOUCHER LA VITRE.
EL VIDRIO CALIENTE
CAUSARÁ QUEMADURAS.
USTED DEBE NUNCA
TOCAR EL VIDRIO CALIENTE.
LOS NIÑOS DEBEN NUNCA
TOCAR EL VIDRIO.
L’écran pare-étincelles fourni avec ce foyer réduit le risque de brûlure en cas de
contact accidentel avec la vitre chaude et doit être installé pour la protection Des
caliente es proveida con este aparato y deberá instalarse para la protección de los
niños y otros individuos en riesgo.
Vea el volante adjunto para la representación de color adecuado
See attached color flyer for proper color representation
Voir ci-joint tract pour une bonne représentation de la couleur
SAFETY AND YOUR FIREPLACE
Installation and Operation Instructions
900476-000, 08/2015
Innovative Hearth Products
RochesterTM See Through and Peninsula Direct Vent Gas Fireplace
3
Afin d’éviter les brûlures
graves ou les blessures,
ne pas retirer l’écran de
protection de la foyer qui
empêche tout contact
direct avec la vitre.
Suivez les instructions de sécurité
ci-dessous et veillez à ce que tous
les membres de votre famille soient
conscients du danger de brûlure
encouru :
Les surfaces de votre foyer deviennent
EXTRÊMEMENT CHAUDES !
des températures EXTRÊMEMENT
ÉLEVÉES et peut causer de graves
blessures en cas de contact.
attentivement les enfants dans les
pièces où un foyer est utilisé afin
la vitre.
chaudes.
Veillez à coller les Étiquettes de mise
à l'endroit où vous
utilisez le foyer, pour rappeler à tous
les utilisateurs les dangers liés aux
températures élevées
(Page 38)
.
Lisez L’information de sûreté
importante (Page 4)
.
Para evitar quemaduras y lesiones
graves, no quite el protector de malla
o guardia de seguridad que evita el
contacto directo con el vidrio.
Siga las instrucciones de seguridad
a continuación y asegúrese de que
todos en su hogar sepan acerca de este
peligro de quemadura:
¡Las superficies de la chimenea se
ponen MUY CALIENTES!
El vidrio delante de la
chimenea alcanza temperaturas
EXTREMADAMENTE ALTAS y puede
causar quemaduras graves si se toca.
Mantenga a los niños alejados de
la chimenea en funcionamiento.
Supervise en forma cercana a los niños
en cualquier cuarto donde haya una
chimenea funcionando para impedir el
contacto con el vidrio.
y otros líquidos inflamables alejados
de la chimenea.
Aún después de haber apagado el
calientes.
Asegúrese de colocar las Etiquetas de
advertencia de seguridad de operación
en el lugar donde enciende la chimenea,
para que todos recuerden los peligros
asociados con las altas temperaturas
(Página 38)
.
Lea Información importante de
seguridad (Página 4).
Seguridad y su
chimenea
La sécurité et
votre foyer
[FRENCH][ENGLISH] [SPANISH]
Safety and Your
Fireplace
To prevent severe burns
and injuries, do Not
remove the barrier on the
appliance which prevents
direct contact with the
glass.
Follow the safety instructions below
and be sure everyone in your household
understands this burn hazard:
The surfaces on your fireplace get
EXTREMELY HOT!
The glass on the front of the
fireplace reaches EXTREMELY HIGH
temperatures and can cause severe
burns if touched.
fireplace. Closely supervise children
fireplace.
hot.
Be sure to attach the enclosed Safety-
in-Operation Warnings where you
turn on your fireplace, to help remind
everyone of the dangers associated with
high temperatures
(Page 38)
.
Read Important Safety Information
(Page 4)
.
All parts of your
IHP fireplace get
EXTREMELY HOT!
Toutes les parties de votre
foyer IHP deviennent
EXTRÊMEMENT CHAUDES !
¡Todas las partes de la
chimenea IHP se ponen
MUY CALIENTES!
Installation and Operation Instructions
900476-000, 08/2015
Innovative Hearth Products
RochesterTM See Through and Peninsula Direct Vent Gas Fireplace
4
Installation and Operation Instructions
900476-000, 08/2015
Innovative Hearth Products
RochesterTM See Through and Peninsula Direct Vent Gas Fireplace
TABLE OF CONTENTS
Packaging .........................................Page 4
Introduction ......................................Page 4
General Information..........................Page 4
Requirements for the
Commonwealth of Massachusetts .Page 6
Cold Climate Insulation.....................Page 7
Manufactured Home Requirements ..Page 7
Location............................................Page 7
Vent Termination Clearances ............Page 8
Appliance and Vent Clearances .........Page 10
Detailed Installation Steps.................Page 11
Typical Installation Sequence ...........Page 12
Step 1. Framing.................................Page 12
Fireplace and Framing Specifications .Page 12
Step 2. Routing Gas Line ..................Page 15
Step 3. Appliance Vent Collar............Page 15
Step 4. Install The Venting System ...Page 16
Vertical Termination Systems............Page 17
Vent Section Length Chart ................Page 17
Vertical Vent Tables and Figures........Page 20
Horizontal Termination System .........Page 22
Horizontal Vent Tables and Figures ...Page 24
Venting Using Flexible Vent Pipe.......Page 27
Step 5. Field Wiring.........................Page 28
Step 6. Optional Blower Kit Wiring..Page 29
Step 7. Connecting Gas Line ...........Page 29
Step 8. Verifying Appliance Operation Page 30
Step 9. Installing Logs ...................Page 32
Step 10. Remove/Install Glass Door .Page 35
Step 11. Burner Adjustments............Page 35
Step 12. Hood Installation.................Page 37
Finishing Requirements ....................Page 37
Step 13. Attaching Safety-in-
Operation Warnings................. Page 38
Installation Accessories ....................Page 39
Gas Conversion Kits .................. Page 41
Operation/Care of Your Appliance .....Page 44
Gas Controls Access.........................Page 47
Variable Flame Adjustment................Page 48
Attaching Safety in
Operation Warnings ......................Page 49
Maintenance......................................Page 50
Front Glass Enclosure Panel,
Removal and Installation.................Page 51
Install Vermiculite, Embers
and Logs........................................Page 52
Burner Flame Appearance/Sooting....Page 55
Burner Flame Adjustments................Page 56
Millivolt Appliance Checkout.............Page 56
Wiring Diagram.................................Page 57
Accessory Components ....................Page 58
Maintenance Schedule......................Page 60
Lighting Instructions – Millivolt ........Page 61
Troubleshooting Guide – Millivolt......Page 63
Replacement Parts List.....................Page 64
Warranty ...........................................Page 67
Please read and understand these
instructions before beginning your
installation.
PACKAGING
The assembled vented gas fireplace heater is
packaged with:
1 - the logs are packaged in a carton located
within the firebox.
2 - oneplasticbagof glowingembersislocated
in the bottom compartment.
3 - one envelope containing the literature
package which consists of Installation and
Operation manual, Hot Glass Safety Flyer,
and Safety-In-Operation Warning Labels;
envelope is located in the bottom compart-
ment.
4 - oneventrestrictortobeappliedasshownon
Page 16;restrictoristaped to the envelope.
5 - two hoods on See-Through units and three
hoods on peninsula fireplaces
6 - top standoffs taped to top of unit
7 - front face assemblies with barriers.
NOTE:
the manufacturer’s barrier for this
appliance.
INTRODUCTION
The Millivolt appliances have a millivolt gas
control valve with piezo ignition system. If any
optional accessories that will require electrical
power are to be installed, the electrical power
must be provided at the time of appliance
installation.
These vented gas fireplace heaters are sealed
combustion, air-circulating gas fireplaces de-
signed for residential applications.
Approved Vent Components - These fireplaces
are designed, tested and listed for operation
and installation with the following vent com-
ponents only:
•Secure Vent®Direct-Vent System Compo-
nents manufactured by Security Chimneys
International,
• ®Flexible Vent Components
manufactured by Security Chimneys Inter-
national and
•Z-FLEX®Model GA Venting Systems listed
to UL1777 and ULCS635 manufactured by
Flexmaster Canada Limited.
Use only the correct size venting (4-1/2" inner
and 7-1/2" outer).
These approved vent system components are
labeled for identification. DO NOT use any
other manufacturer’s vent components with
these appliances.
Children and adults should be alerted to the
hazards of high surface temperature and
should stay away to avoid burns or clothing
ignition.
Les enfants et les adultes devraient être infor-
mésdes dangers queposent les températures
de surface élevées et se tenir à distance afin
d’éviter des brûlures ou que leurs vêtements
ne s’enflamment.
DO NOT ATTEMPT TO ALTER OR MODIFY
THE CONSTRUCTION OF THE APPLIANCE OR
ITS COMPONENTS. ANY MODIFICATION OR
CERTIFICATION AND LISTINGS OF THIS UNIT.
WARNING
Young children should be care-
in the same room as the appli-
and others may be susceptible
to accidental contact burns. A
physicalbarrierisrecommended
if there are at-risk individuals in
the house. To restrict access to
adjustable safety gate to keep
other at-risk individuals out of
surfaces.
AVERTISSEMENT
Lesjeunesenfantsdevraientêtre
surveillésétroitementlorsqu’ils
se trouvent dans la même pièce
lesjeunesenfantsoulesadultes
peuvent subir des brûlures s’ils
viennent en contact avec la sur-
facechaude. Ilestrecommandé
d’installerunebarrièrephysique
-
tent la maison. Pour empêcher
installez une barrière de sécu-
surfaces chaudes.
GENERAL INFORMATION
5
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
Installation and Operation Instructions
900476-000, 08/2015
Innovative Hearth Products
RochesterTM See Through and Peninsula Direct Vent Gas Fireplace
WARNING
I -
maintenance can cause injury
or property damage. Refer to
this manual. For assistance or
additional information consult
agency or the gas supplier.
WARNING
in an improperly installed and
-
ance and/or its operating controls
is dangerous.
WARNING
Clothing or other flammable
material should not be placed
on or near the appliance.
AVERTISSEMENT
On ne devrait pas placer de
vêtements ni d’autres matières
WARNING
barrier removed for servicing
an appliance must be replaced
priortooperatingtheappliance.
AVERTISSEMENT
Tout écran ou protecteur retiré
pour permettre l’entretien de
l’appareil doit être remis en
place avant de mettre l’appareil
en marche.
NOTE: Installation and repair should be done
by a qualified service person. The appliance
should be inspected before use and at least
annually by a professional service person.
More frequent cleaning may be required due
to excessive lint from carpeting, bedding ma-
terial, et cetera. It is imperative that control
compartments, burners and circulating air
passageways of the appliance be kept clean.
Remarque: L’installation et la réparation
devrait être confiées à un technicien qualifié.
L’appareil devrait faire l’objet d’une inspection
par un technicien professionnel avant d’être
utilisé et au moins une fois l’an par la suite.
Des nettoyages plus fréquents peuvent être
nécessaires si les tapis, la literie, et cetera
produisent une quantité importante de pous-
sière. Il est essentiel que les compartiments
abritant les commandes, les brûleurs et les
conduits de circulation d’air de l’appareil
soient tenus propres.
Do not use this appliance if any part has
qualified service technician to inspect the
appliance and to replace any part of the
-
peler un technicien qualifié pour inspecter
l’appareil et remplacer toute partie du
systèmede commande ettoutecommande
qui a été plongée dans l’eau.
IMPROPER INSTALLATION OR USE OF THIS
APPLIANCE CAN CAUSE SERIOUS INJURY OR
CARBON MONOXIDE POISONING.
Only trim kit(s) supplied by the manufacturer
shall be used in the installation of this ap-
pliance.
Seules les trousses de garniture fournies
par le fabricant doivent être utilisées pour
l’installation de cet appareil.
These appliances comply with National Safety
Standards and are tested and listed by PFS
(ReportNo.F14-165)toANSIZ21.88(inCanada,
CSA-2.33), and CAN/CGA-2.17-M91, latest edi-
tions, in both USA and Canada, as vented gas
fireplace heaters
These appliances are listed by PFS Cor-
poration for installation in bedrooms and
Manufactured Homes.
Misc. Codes / Standards -
TheInstallationmustconform tolocal codesor,
in the absence of local codes, with the National
Fuel Gas Code, ANSI Z223.1/NFPA 54—latest
edition, or the Natural Gas and Propane Instal-
lation Code, CSA B149.1.
The appliance, when installed, must be electri-
cally grounded and wired in accordance with
local codes or, in the absence of local codes,
with the National Electrical Code, ANSI/NFPA
70—latest edition, or the Canadian Electrical
Code, CSA C22.1—latest edition.
Provide adequate clearances around air open-
ings and adequate accessibility clearance for
service and proper operation. Never obstruct
the front or back openings of the appliance.
These appliances are designed to operate on
natural or propane gas only. The use of other
the performance of this system and may be
dangerous.
These fireplaces are designed as supplemental
heaters. Therefore, it is advisable to have an
alternate primary heat source when installed
in a dwelling.
Millivolt Models - The millivolt appliances are
manually controlled and feature a spark igniter
(piezo) that allows the appliance's pilot gas to
be lit without the use of matches or batteries.
This system provides continued service in the
event of a power outage.
Millivoltmodels comestandard witha manually-
modulatedgas valve;flameappearance andheat
outputcanbecontrolledatthegasvalve.TheBTU
Input for these appliances is shown in Table 1.
Models Fuel
Type
Input Rate
Natural
Propane
Table 1
Efficiencies %
Natural Gas Propane
Models AFUE P4 AFUE P4
35" ST 68.8 59.03 70.3 58.66
35" PF 69.2 60.1 69.7 58.66
NOTE:Ifthebarrierbecomesdam-
this appliance.
6
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
Installation and Operation Instructions
900476-000, 08/2015
Innovative Hearth Products
RochesterTM See Through and Peninsula Direct Vent Gas Fireplace
Test gauge connections are provided on the
front of the millivolt gas control valve (identi-
fied IN for the inlet and OUT for the manifold
side). The control valves have a 3/8" (10mm)
NPT thread inlet and outlet side of the valve
(refer to Figure 1).
Propane tanks are at pressures that will cause
damage to valve components. Verify that the
tanks have step down regulators to reduce the
pressure to safe levels.
Gas Valve Diagrams
See the millivolt gas valve in Figure 1.
Manifold Gas Supply Pressure
Fuel # High
Natural
Gas
Propane
Table 3
The appliance must be isolated from the
gas supply piping system by closing its
equipmentshutoffvalveduringanypressure
testing of the gas supply piping system at
test pressures equal to or less than 1/2
psig (3.5 kPa).
The appliance and its appliance main gas
valve must be disconnected from the gas
supply piping system during any pressure
testing of that system at test pressures in
1/2 psig (3.5 kPa).
Orifice Sizes - Sea Level to High Altitude
These appliances are tested and approved for
installation at elevations of 0-4500 feet (0-1372
meters)abovesealevelusingthestandardburner
orifice sizes (marked with an "*" in Table 4 ).
For elevations above 4500 feet, contact your
gas supplier or qualified service technician.
Deration - At higher elevations, the amount
of BTU fuel value delivered must be reduced
by either using gas that has been derated by
the gas company or by changing the burner
orifice to a smaller size as regulated by the
local authorities having jurisdiction and by the
(USA) National Fuel Gas Code NFPA 54/ANSI
Z223.1—latest edition or, in Canada, the CAN/
CSA-B149.1 codes—latest edition.
Installtheapplianceaccordingtotheregulations
of the local authorities having jurisdiction and,
in the USA, the National Fuel Gas Code NFPA
54 / ANSI Z223.1—latest edition or, in Canada,
the CAN/CSA-B149.1—latest edition.
Flame breadth, height and width will dimenish
4% for every 1,000 feet of altitude.
COMMONWEALTH OF MASSACHUSETTS
REQUIREMENTS
Theseappliancesareapprovedforinstallationin
the US state of Massachusetts if the following
additional requirements are met:
• Install this appliance in accordance with
Massachusetts Rules and Regulations 248
C.M.R. Sections 4.00 through 8.00.
• Installationandrepairmustbedonebya
plumber or gas fitter licensed in the Com-
monwealth of Massachusetts.
• Theexiblegasline connectorusedshall
not exceed 36 inches (92 centimeters) in
length.
• Theindividualmanual shut-off must be a
T-handle type valve.
Massachusetts Horizontal Vent Requirements
-
zontal terminations installed less than seven
• A hard wired carbon monoxide detector
with an alarm and battery back-up must be
installed on the floor level where the gas
fireplace is installed. The carbon monoxide
detector must comply with NFPA 720, be
ANSI/UL 2034 listed and be ISA certified..
• Ametalorplasticidenticationplatemust
be permanently mounted to the exterior of
thebuilding at a minimum heightofeight (8)
feet above grade and be directly in line with
the horizontal termination. The sign must
read, in print size no less than one-half (1/2)
inch in size, GAS VENT DIRECTLY BELOW.
KEEP CLEAR OF ALL OBSTRUCTIONS.
Inlet Gas Supply Pressure
Fuel # Minimum
Natural Gas 4.5" WC
10.5" WC
Propane 11.0" WC
13.0" WC
Table 2
Gas Pressure - All Models
Tables 2 and 3 show the appliances' inlet and
manifold gas pressure requirements:
H
I
LO
W
HTPTHTPT
P
I
L
O
T
P
I
L
O
T
O
N
it
O
F
F
IN OUT
HI/LO Variable
Flame Height
Adjustment
Figure 1 - SIT Millivolt Gas Valve
Manifold Pressure Tap
Inlet Pressure Tap
Pilot Adjustment
Main Gas Control Knob
OFF/PILOT/ON
Elevation
Natural
Gas
Propane
Gas
0-4500
#37 *
1.55
mm
*
Table 4 * Standard size installed at factory
• Part /Cat. Number
7
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
Installation and Operation Instructions
900476-000, 08/2015
Innovative Hearth Products
RochesterTM See Through and Peninsula Direct Vent Gas Fireplace
LOCATION
In selecting the location, the aesthetic and functional use of the appliance are primary concerns.
However, vent system routing to the exterior and access to the fuel supply are also important.
Due to high temperatures, the appliance should be located out of traffic and away from furniture
and draperies (Figure 3).
En raison des températures élevées, l’appareil devrait être installé dans un endroit où il y a
peu de circulation et loin du mobilier et des tentures (Figure 3).
The location should also be free of electrical, plumbing or other heating/air conditioning ducting.
These direct-vent appliances are uniquely suited for installations requiring a utility shelf positioned
directly above the fireplace. Utility shelves like these are commonly used for locating television
sets and decorative plants.
COLD CLIMATE INSULATION
For cold climate installations, seal all cracks
around your appliance with noncombustible
material and wherever cold air could enter
the room. It is especially important to insulate
outside chase cavity between studs and under
floor on which appliance rests, if floor is above
ground level. Gas line holes and other open-
ings should be caulked or stuffed with unfaced
fiberglass insulation.
If the fireplace is being installed on a cement
slab in cold climates, a sheet of plywood or
otherraised platform can be placed underneath
to prevent conduction of cold transferring to
the fireplace and into the room. It also helps to
sheetrockinsidesurfacesandtapeformaximum
air tightness and caulk firestops.
MANUFACTURED HOME
REQUIREMENTS
Thisappliancemaybeinstalledinanaftermarket
permanently located, manufactured home and
must be installed in accordance with the manu-
facturer's instructions and the Manufactured
Home Construction and Safety Standard, Title
24 CFR, Part 3280, in the United States, or the
StandardforInstallationinMobileHomes,CAN/
CSA Z240 MH Series, in Canada.
Cetappareilpeutêtreinstallécómmedu matéri-
eld'originedansunemaisonpréfabriquée(É.U.
seulement) ou mobile et doit être installé selon
les instructions du fabricant et conformément
à la norme Manufactured Home Constructions
and Safety, Title 24 CFR, Part 3200 aux Unis ou
à la norme Can/CSA-Z240 Série MM, Maisons
mobiles au Canada.
Thisapplianceisonlyforusewiththetypeofgas
indicated on the rating plate. This appliance is
not convertible for use with other gases, unless
a certified kit is used.
Cet appareil doit être utilisé uniquement avec le
type de gaz indiqué sur la plaque signalétique.
Cetappareilne peutêtreconvertiàd'autres gaz,
sauf si une trousse de conversion est utilisée.
CAUTION: Ensure that the cross mem-
installation. The structural integrity of
ceiling / roof must be maintained.
CAUTION: This appliance must be ground-
ed to the chassis of the manufactured
National Electrical Code ANSI / NFPA 70—
latest edition or the Canadian Electrical
Code CSA C22.1—latest edition.
Figure 3
Vertical
Venting
Offset Venting
Vertical
Vent
Horizontal Vent
Horizontal Vent
8
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
Installation and Operation Instructions
900476-000, 08/2015
Innovative Hearth Products
RochesterTM See Through and Peninsula Direct Vent Gas Fireplace
12
X
Roof Pitch is X/12
2 FT
MIN.
2 FT MIN.
Lowest
Discharge
Opening
H*
*H = MINIMUM HEIGHT FROM ROOF TO
LOWEST DISCHARGE OPENING OF VENT
TERMINATION HEIGHTS FOR VENTS ABOVE
FLAT OR SLOPED ROOFS
Horizontal Overhang
Vertical
Wall
Vent
Termination
Storm Collar
Concentric
Vent Pipe
Flashing
1 inch (25.4 mm) Minimum
Clearance to Combustibles
Figure 5
Vertical Vent Termination Clearances
Be aware that this is a heat producing ap-
pliance. Objects placed above the unit are
exposed to elevated temperatures.
-
ance and the area above it (see Figure 8 ).
Theminimum height from the base of the appli-
ance to the underside of combustible materials
used to construct a utility shelf in this fashion
is shown in Figure 8.
The appliance should be mounted on a fully
supported base extending the full width and
depth of the unit. The appliance may be located
onornearconventionalconstructionmaterials.
However, if installed on combustible materials,
such as carpeting, vinyl tile, etc., a metal or
woodbarriercoveringtheentirebottomsurface
must be used.
VENT TERMINATION CLEARANCES
These instructions should be used as a
guideline and do not supersede local codes
the current standards of CAN/CSA-B149.1
in Canada.
Vertical Vent Termination Clearances
Terminate multiplevent terminationsaccording to
the installation codes listed above and Figures
4 and 5.
Note - See Figure 36 on Page 23 for the exterior wall recess
allowances of the square horizontal termination.
Termination Heights For Vents
Above Flat Or Sloped Roofs
Ref. NFPA 54 / ANSI Z223.1
Roof Pitch * Feet *Meters
Flat to 6/12 1.0 0.3
6/12 to 7/12 1.25 0.38
7/12 to 8/12 1.5 0.46
8/12 to 9/12 2.0 0.61
9/12 to 10/12 2.5 0.76
10/12 to 11/12 3.25 0.99
11/12 to 12/12 4.0 1.22
12/12 to 14/12 5.0 1.52
14/12 to 16/12 6.0 1.83
16/12 to 18/12 7.0 2.13
18/12 to 20/12 7.5 2.29
20/12 to 21/12 8.0 2.44
The vent / air intake termination clearances
above the high side of an angled roof is as
shown in the following chart:
Figure 6
6"
(152 mm)
12"
(305 mm)
Combustible Projection greater
Horizontal Vent Termination Clearances
Combustible Projection
2-1/2 inches or less in length
18"
(457 mm)
Ventilated
Soffit Unventilated
Soffit
than 2-1/2 inches in length
Termination Kit
Side Elevation View
Termination Kit
All horizontal terminations
may be located as close as
6” (152mm) to any
(non-combustible and
combustible) exterior
sidewall. This distance
may be decreased to 2”
(51mm) for non--
combustible exterior
sidewalls only, if the
SV4.5HT-2 termination
is used.
Horizontal Vent Termination Clearances
The horizontal vent termination must have a minimum of 6" (152 mm) clearance to any overhead
combustible projection of 2-1/2" (64 mm) or less (see Figure 6). For projections exceeding 2-1/2"
(64 mm), see Figure 6. For additional vent location restrictions refer to Page 9.
Figure 4 - Multiple Terminations
12”
Minimum
These appliances must not be connected to a
chimney or flue serving a separate solid fuel
burning appliance.
9
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
Installation and Operation Instructions
900476-000, 08/2015
Innovative Hearth Products
RochesterTM See Through and Peninsula Direct Vent Gas Fireplace
EXTERIOR HORIZONTAL VENT TERMINATION CLEARANCE REQUIREMENTS
U.S. Installation ** Canadian Installation *
AClearance above grade, veranda, porch, desk, or balcony 12” (300 mm) ** 12” (300 mm) *
BClearance to window or door that may be opened 6” (150 mm)
for fireplaces < 10,000 Btu/h (3 kW),
9” (230 mm)
for fireplaces > 10,000 Btu/h (3 kW), and < 50,000 Btu/h
(15 kW),
12” (300 mm)
for fireplaces > 50,000 Btu/h (15 kW) **
6” (150 mm)
for fireplaces < 10,000 Btu/h (3 kW),
12” (300 mm)
for fireplaces > 10,000 Btu/h (3 kW)
CClearance to permanently closed window 9” (229 mm)
recommended to prevent window condensation
12” (305 mm)
recommended to prevent
window condensation
DVertical clearance to ventilated soffit located above the
termination within a horizontal distance of 18” (458 mm)
18” (458 mm) 18” (458 mm)
EClearance to unventilated soffit 12” (305 mm) 12” (305 mm)
FClearance to outside corner 5” (127 mm)
minimum
5” (127 mm)
minimum
GClearance to inside corner 6” (152 mm) minimum *** 6” (152 mm) minimum ***
HClearance to each inside of center line extended above
meter / regulator assembly
36” (910 mm)
within a height of 15 ft above the meter / regulator assembly **
36” (910 mm)
within a height of 15 ft above the meter /
regulator assembly *
IClearance to service regulator vent outlet 36” (910 mm)** 36” (910 mm)*
JClearance to nonmechanical air supply inlet to building or
the combustion air inlet to any other fireplace
6” (150 mm)
for fireplaces < 10,000 Btu/h (3 kW),
9” (230 mm)
for fireplaces > 10,000 Btu/h (3 kW) and < 50,000 Btu/h (15 kW),
12” (300 mm)
for fireplaces > 50,000 Btu/h (15 kW)**
6” (150 mm)
for fireplaces < 10,000 Btu/h (3 kW),
12” (300 mm)
for fireplaces > 10,000 Btu/h (3 kW)
KClearance to a mechanical air supply inlet 36” (910 mm) above if within 10 ft (3 m) horizontally ** 72” (1830 mm) *
LClearance above paved sidewalk or paved diveway located
on public property
84” (2130 mm) ‡ 84” (2130 mm) ‡
MClearance under veranda, porch, deck or balcony 12” (300 mm) *‡ 12” (300 mm) *‡
NDepth of alcove (maximum) 72” (1830 mm) ** 72” (1830 mm) *
OClearance to termination (alcove) 6” (15.2 mm) ** 6” (15.2 mm)*
PWidth of alcove (minimum) 36” (910 mm) ** 36” (910 mm) *
QClearance to combustible above (alcove) 18” (457 mm) ** 18” (457 mm) *
Fixed
Closed Openable Fixed
Closed
V
V
VV
V
V
X
X
VX
G
G
J
F
B
B
K
H
I
A
E
L
D
B
M
C
B
V
V
A
G
G
B
TERMINATION CAP AIR SUPPLY INLET GAS METER RESTRICTED AREA
(TERMINATION PROHIBITED)
Openable
See Figure 5
V
V
Inside Corner
VV
Outside Corner Recessed Location
Balcony with No Side Wall
V
Balcony with Perpendicular Side Wall
G
F
M
M
NP
O
Q
* In accordance with the current CAN/CGA-B149.1 National Gas And Propane Installation Code
** In accordance with the curent ANSI Z223.1/NFPA 54 National Fuel Gas Codes
*** This distance may be decreased to 2” (51mm) for noncombustible exterior sidewalls with all approved terminations
‡ A vent shall not terminate directly above a sidewalk or paved driveway which is located between two single family dwellings and serves both dwellings
*‡ Only permitted if veranda, porch, deck, or balcony is fully-open on a minimum two sides beneath the floor
10
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
Installation and Operation Instructions
900476-000, 08/2015
Innovative Hearth Products
RochesterTM See Through and Peninsula Direct Vent Gas Fireplace
MINIMUM CLEARANCES TO COMBUSTIBLES
Appliance And Vent Clearances
The appliance is approved with zero clearance to combustible materials on all sides (as detailed
in Table 5), with the following exception: When the unit is installed with one side flush with a
wall, the wall on the other side of the unit must not extend beyond the front edge of the unit.
In addition, when the unit is recessed, the side walls surrounding the unit must not extend beyond
the front edge of the unit (see Figure 3).
*NOTE: 3" (75 mm) above any horizontal/inclined vent component.
**NOTE: See Page 12, Step 1 for clearance requirements to the nailing flange located at each
side of the unit and any screw heads adjacent to it.
- A hearth extension is not
required with this appliance. If a hearth exten-
sion is used, do not block the lower control
compartment door. Any hearth extension used
is for appearance only and does not have to
conform to standard hearth extension instal-
lation requirements.
Shelf Height - To provide for the lowest pos-
sible shelf surface, use the alternate rear vent
outlet,theventingattachedtothetopventshould
be routed in a way to minimize obstructions to
the space above the appliance. Do not insulate
Figure 8). The minimum height
from the base of the appliance to the underside
of combustible materials used to construct a
utility shelf in this fashion is shown in Figure 8.
The appliance should be mounted on a fully
supported base extending the full width and
depth of the unit. The appliance may be located
onornearconventionalconstructionmaterials.
However, if installed on combustible materials,
such as carpeting, vinyl tile, etc., a metal or
woodbarriercoveringtheentirebottomsurface
must be used.
Wall Finishes / Surrounds / Mantels
NOTE: Combustible wall finish materials and/
or surround materials must not be allowed to
encroach the area defined by the appliance front
face (black sheet metal). Never allow combus-
tible materials to be positioned in front of or
overlapping the appliance face (see Figure 65
on Page 37).
Minimum clearance requirements include any
projections such as shelves, window sills,
mantels, etc. above the appliance.
Non-combustible materials, such as surrounds
and other appliance trim, may be installed on
the appliance face with these exceptions: they
must not cover any portion of the removable
glass panel or control compartment.
Vertical installation clearances to combustible
mantels vary according to the depth of the
mantel. See Figure 7. Mantels constructed of
non-combustible materials may be installed
at any height above the appliance opening;
however, do not allow anything to hang below
the fireplace hood.
5" Standoff
9 (289)
2
(51)
4
(102)
6
(152)
8
(203)
10
(254)
12
(305)
11 (279)
15 (381)
19 (483)
17 (432)
13 (330)
Figure 8 -
Shelf Height Minimum Clearances
Shelf Height
Shelf Above Fireplace With Side Venting
Do not insulate this space
above the appliance.
Shelf Height
Shelf Above Fireplace With Top Venting
Mantel Depth
Top of
Appliance
Front or Rear Face
of Appliance
Figure 7 - Minimum Mantel Clearances
Model No.
Side Vent - Straight Out Back
Secure Vent
ST/PF
Do not insulate this space
above the appliance.
11
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
Installation and Operation Instructions
900476-000, 08/2015
Innovative Hearth Products
RochesterTM See Through and Peninsula Direct Vent Gas Fireplace
MINIMUM CLEARANCES*
Sides
Top of Appliance
Floor
From Bottom of Unit To Ceiling
Vent TopSides & Bottom
SERVICE CLEARANCES
Table 5
WARNING
diagrams or failure to use only parts specifically
damage or personal injury.
AVERTISSEMENT
Risque de dommages ou de blessures si les pièces
et ou si des pièces autres que celles spécifiquement
approuvées avec cet appareil sont utilisées.
DETAILED INSTALLATION STEPS
The appliance is shipped with all gas controls and components installed
and pre-wired.
1. Remove the shipping pad, exposing the front face assembly with
barrier and hood. Remove the hood by pulling firmly straight away
from the unit.
2. Removethefaceassembly withbarrierbyliftingthefrontface assembly
approximately 1/2" then pull straight out away from the fireplace until
the mounting tabs clear, exposing the glass door.
3. Open the two latches (located under the firebox floor) securing the
glass door. Remove the door by tilting it outward at the bottom and
lifting it up. Set the door aside protecting it from inadvertent damage.
See Removing and Installing Glass Panels on Page 35.
4. Lift the pressure relief plates and remove the cardboard from beneath
each plate (be careful not to damage the white gasket).
1
(25)
2
(51)
3
(76)
1 (25)
2 (51)
3 (76)
4
(102)
4 (102)
5
(127)
5 (127)
6 (152)
7 (178)
8 (203)
9 (229)
10 (250)
Combustible Materials
“Safe Zone”
Fireplace
45o
At 5" minimum side
be any length.
Minimum
Distance to
Unprotected
Side Wall
One end of the unit may be
the front edge of the unit.
Figure 9
12
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
Unit Being Secured by Its Nailing
Flanges to the Framing
Installation and Operation Instructions
900476-000, 08/2015
Innovative Hearth Products
RochesterTM See Through and Peninsula Direct Vent Gas Fireplace
Figure 11
REMOVE
CARDBOARD
BEFORE USING
Pressure Relief
Plates
Remove Cardboard Before
Using Appliance
REMOVE
CARDBOARD
BEFORE USING
Figure 12 - Nailing Flanges
Step 1. FRAMING
Frametheseappliances asillustratedin Figures
13 and 14 on Pages 13 and 14. All framing
details must allow for a minimum clearance
to combustible framing members as shown
in Table 5 on Page 11.
Iftheappliance istobe elevatedabovefloorlevel,
asolidcontinuousplatformmustbeconstructed
below the appliance.
Headers may be in direct contact with the appli-
ancetopspacerswhentheyarebentupvertically
maintainingthe3"clearancetothefireplacetop,
but must not be supported by them or notched
to fit around them. All construction above the
appliancemustbeself-supporting. DO NOTuse
the appliance for structural support.
The fireplace should be secured to the side
framing members using the unit's nailing
flanges - one top and bottom on each side of
the fireplace front. See Figure 12. Use 8d nails
or their equivalent.
TYPICAL INSTALLATION SEQUENCE
The typical sequence of installation is outlined
below. However,eachinstallation is uniqueand
may result in variations to the steps described.
See the page numbers references in the follow-
ing steps for detailed procedures.
Step 1. (Page 12) Construct the appliance
framing. Position the appliance within the
framing and secure with nailing brackets. Bend
up the appropriate header spacing guides for
the drywall/finish material thickness to be used
(refer to Figure 65, Page 37). Bend up the
outer pair for 1/2" materials and the inner pair
for 5/8" materials. Bend out the appropriate
nailing flanges for the drywall/finish material
to be used. Nailing flanges are provided for
flush framing, 1/2" and 5/8" framing depths
(see Figure 12).
Step 2. (Page 15)Route gas supply line to
appliance location.
Step 3. Preparing the appliance vent collar
(Page 15).
Step 4. (Page 16)Install the vent system and
exterior termination.
Step 5. (Page 28)Field Wiring
a. Millivolt Appliances – Install the operating
control switch (not factory provided) and bring
inelectricalservicelineforforcedair-circulating
blower (optional equipment).
Step 6. (Page 29)Install blower kit (optional
equipment).
Step 7. (Page 29)Make connection to gas
supply.
Step8.(Page30)Verifyingapplianceoperation.
Step 9. (Page 32)Install the logs, decorative
volcanic stone and glowing embers.
Step10. (Page 35) Installglass doorassembly.
Step 11. (Page 35) Adjust burner to ensure
proper flame appearance.
Step 12. (Page 37) Install front face assembly
with barrier. Install the hoods.
Step 13. (Page 38) Attach Safety in Operation
Warnings.
Before proceeding it may be helpful to remove
the log set form the firebox and remove the
embers and volcanic stone from the control
compartment. Refer to the following steps:
1. Remove the front face assembly, hood
and glass enclosure panel (seeRemoving and
Installing Glass Enclosure Panels on Page 35).
2. Remove log set box from firebox. Next,
remove embers and volcanic stone from con-
trol compartment. Handle logs carefully to
prevent breakage.
13
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
Installation and Operation Instructions
900476-000, 08/2015
Innovative Hearth Products
RochesterTM See Through and Peninsula Direct Vent Gas Fireplace
RochesterST
NOTES
Appliance has a factory-installed vent seal
Figures 16 & 17 on Page 16)in each
flue outlet.
SPECIFICATIONS
Natural Gas BTU Input
Propane Gas BTU Input
4-1/2" Inner /
7-1/2" Outer
5-5/8
(143)
***39-7/8
(1013)
37-3/16
(945)
**20-3/4
(527)
10-1/2
(267)
12-1/8
(308) 5-1/8
(130)
12-1/8
(308)
25-1/2
(648)
5-1/8
(130)
Vent Center - Top Vent
Vent Center - Side Vent
Secure Vent®
®
**This dimension
finished dimension
Center of gas line
is 3-1/8 inches
floor.
***This dimension does
not include the addition
framing or clearance for
the Side Vent Seal Cap.
Adjust accordingly for your
installation.
SideVent SealCap
37-1/4"
Based on CSA P. 4.1-09
11 (279)
6-1/4
(159)
25-1/2
(648)
3-1/8 (79)
10-7/8 (264)
11 (279)
(16)
5/8
37-1/16
(941)
18-1/4
(464)
1-1/4
(44)
4-15/16
(125)
25-1/2
(648)
41-13/16 (1062)
40-1/4 (1022)
35-1/4 (895)
29 (737)
32-5/8 (829)
11 (279)
6-1/4
(159)
3-1/8 (79)
Figure 13
Control Compartment
Door
Gas
Inlet
Knock-Out
Provide
additional
space for
Side Vent
Seal Cap if
installing
against
a solid
Framing Spacers
Vent Seal Cap
Optional
Knock-Out
Gas
Inlet
37-1/8"
5"
Vertical Venting Through the Ceiling:
Frame ceiling opening -Use a plumb line
from the ceiling above the appliance to
locate center of the vertical run. Cut and/or
frame an opening, 10-1/2" x 10-1/2" (267
mm x 267 mm) inside dimensions, about
this center mark (see Figure 20).
14
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
Installation and Operation Instructions
900476-000, 08/2015
Innovative Hearth Products
RochesterTM See Through and Peninsula Direct Vent Gas Fireplace
RochesterPF
SPECIFICATIONS
Natural Gas BTU Input
Propane Gas BTU Input
4-1/2" Inner /
7-1/2" Outer
NOTES
Appliance has a factory-installed vent seal cap
Figures 16 & 17 on Page 16)in each flue
outlet.
5-5/8
(143)
***38-3/4
(984)
37-3/16
(945)
**20-3/4
(527)
10-1/2
(267)
12-1/8
(308) 5-1/8
(130)
12-1/8
(308)
25-1/2
(648)
5-1/8
(130)
Vent Center - Top Vent
Vent Center - Side Vent
Secure Vent
**This dimension
finished dimension
for
gas line inlet location options.
Fireplace Framing Specifications
Center of gas line
is 3-1/8 inches
floor.
Notes:
***This dimension does
not include the addition
framing or clearance for
the Side Vent Seal Cap.
Adjust accordingly for your
installation.
Side Vent Seal Cap
Figure 14
Vertical Venting Through the Ceiling:
Frame ceiling opening -Use a plumb line
from the ceiling above the appliance to
locate center of the vertical run. Cut and/or
frame an opening, 10-1/2" x 10-1/2" (267
mm x 267 mm) inside dimensions, about
this center mark (see Figure 20).
11 (279)
6-1/4
(159)
25-1/2
(648)
3-1/8 (79)
10-7/8 (264)
11 (279)
(16)
5/8
25-5/16 (643)
22 (559)
15-3/4 (400)
19-11/16 (500)
37-1/16
(941) 18-1/4
(465)
29-3/16
(741)
37-1/16
(941)
18-1/4
(464)
1-1/4
(44)
4-15/16
(125)
25-1/2
(648)
41-13/16 (1062)
40-1/4 (1022)
35-1/4 (895)
29 (737)
32-5/8 (829)
Control Compartment
Door
Gas
Inlet
Knock-Out
Provide
additional
space for
Side Vent
Seal Cap if
installing
against
a solid
Framing Spacers
Vent Seal Cap
Optional
Based on CSA P. 4.1-09
15
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
Installation and Operation Instructions
900476-000, 08/2015
Innovative Hearth Products
RochesterTM See Through and Peninsula Direct Vent Gas Fireplace
Schedule 40
Black Iron Pipe
Schedule 40 Pipe
Natural
Gas
Propane
Gas
0-10 1/2 3/8
10-40 1/2 1/2
40-100 1/2 1/2
100-150 3/4 1/2
150-200 3/4 1/2
Table 6
IMPORTANT: If propane is used, be aware that
if tank size is too small (i.e. under 100-lbs, if
this is the only gas appliance in the dwelling.
Ref. NPFA 58), there may be loss of pressure,
resulting in insufficient fuel delivery (which
can result in sooting, severe delayed ignition
or other malfunctions). Any damage resulting
from an improper installation, such as this,
is not covered under the limited warranty.
Step 3. PREPARING THE APPLIANCE
VENT COLLAR
Proper Sizing of Gas Line
Properly size and route the gas supply line from
thesupply regulator to the area wheretheappli-
anceistobeinstalledperrequirementsoutlined
in the National Fuel Gas Code, NFPA 54—latest
edition (USA) or CAN/CSA-B149.1—latest edi-
tion (Canada).
Never use galvanized or plastic pipe. Refer to
Table 6 for proper sizing of the gas supply line,
if black iron pipe is being used. Gas lines must
be routed, constructed and made of materials
that are in strict accordance with local codes
andregulations. Werecommendthataqualified
individual such as a plumber or gas fitter be
hired to correctly size and route the gas supply
line to the appliance.
Also see Figures 13 and 14.
Figure 15 - Route Gas Line
Step 2. ROUTING GAS LINE
Route a 1/2" (13 mm) gas line to the left side
of the appliance as shown in Figure 15. Gas
lines must be routed, constructed and made
of materials that are in strict accordance with
local codes and regulations. All appliances
are factory-equipped with a flexible gas line
connector and 1/2" shutoff valve. Step
6 on Page 29).
5-5/8"
(143 mm)
3-1/8"
(79 mm)
Notes:
• Allappliancesarefactory-equippedwitha
flexible gas line connector and 1/2" shutoff
valve (see Figure 50 on Page 31).
• SeeMassachusetts Requirements onPage
6foradditionalrequirementsforinstallations
in the state of Massachusetts in the USA.
• ThegassupplylineshouldNotbeconnected
to the appliance until Step 6 (Page 29).
• Apipejointcompoundratedforgasshouldbe
usedonthethreadedjoints.Ensure propane
resistant compounds are used in propane
applications. Be very careful that the pipe
compound does not get inside the pipe.
• Itisrecommendedtoinstallasedimenttrap
in the supply line as close as possible to the
appliance. AppliancesusingPropane should
have a sediment trap at the base of the tank.
• Checkwithlocal building ofcial for local
code requirements (i.e. are below grade
penetrations of the gas line allowed?, etc).
REMOVE VENT SEAL CAP
Top Vent Installations - See Figure 16
Side Vent Installations - See Figure 17
Preparing the Appliance Vent Collar
Each of the appliances' two vent collars are
sealed with a seal cap which must be removed
from the vent collar being used. In top vent
installation the cover plate shall be removed
from the inside. Refer to Figure 16 for top
vent installations and Figure 17 for side vent
installations and the following steps to prepare
the appropriate collar for use.
From the vent collar being used, remove the
two screws securing the vent seal cap. Twist
the cap counterclockwise. Pull it away from
the appliance and discard, along with the piece
of insulation.
WARNING
Failure to reinstall and securely
could result in leakage of flue
products into the living space.
Vent seal cap must remain
securely installed on unused
vent collar. Failure to do so
could result in leakage of flue
products into living space.
16
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
Installation and Operation Instructions
900476-000, 08/2015
Innovative Hearth Products
RochesterTM See Through and Peninsula Direct Vent Gas Fireplace
Appli
Insulation
Top Vent Vent Seal Cap
Cabinet Top
CROSS SECTION
SIDE VENT SEAL CAP REMOVAL
Insulation Vent Seal Cap
Side Vent
Cabinet Back
CROSS SECTION
Appli
Appli
Figure 16 -
Figure 17 -
TOP VENT SEAL CAP REMOVAL
Step 4. INSTALL THE VENT SYSTEM
General Information
Theseinstructions should be used as a guideline and donotsupersede
USA or the current standards of CAN/CSA-B149.1 in Canada.
the requirements of the gas supplier.
du foumisseunde gaz.
Use only approved venting components. See Approved Vent
Components on Page 4.
These fireplaces must be vented directly to the outside.
The vent system may not service multiple appliances, and must never
be connected to a flue serving a solid fuel burning appliance. The vent
pipe is tested to be run inside an enclosed wall (such as a chase). There
is no requirement for inspection openings in the enclosing wall at any of
the joints in the vent pipe.
Installation of Vent Restrictor
A vent restrictor may be needed with this appliance. The restrictor is
installed in the appliance top flue outlet as shown in Figure 16, either
before adding vent, from above, or after installation of vent from below,
within the firebox. The restrictor is self securing through a positive
friction fit.
Determine the venting for the appliance.
collar before connecting any vent (Refer to Figure 18). Place the
restrictor inside the appliance vent collar and press in place.
NOTE: The restrictor is included within the firebox.
Select Venting System - Horizontal or Vertical
With the appliance secured in framing, determine vent routing and identify
the exterior termination location. The following sections describe vertical
(roof) and horizontal (exterior wall) vent applications. Refer to the section
relating to your installation. A list of approved venting components are
Pages 39 and 40.
Figure 18
Appliance Top
Vent Outlet
Restrictor
Inner
Fireplace
Collar
VENT RESTRICTOR INSTALLATION
A vent restrictor may be needed when vertically terminating the vent
system above the roof (when using the appliance top vent), install a vent
restrictor in the top vent of the fireplace outlet.
If needed, install the restrictor as shown, either from inside or outside the
unit, in the inner fireplace collar.
Cover Plate
17
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
Installation and Operation Instructions
900476-000, 08/2015
Innovative Hearth Products
RochesterTM See Through and Peninsula Direct Vent Gas Fireplace
NOTE: Convert inches into metric equivalent
TRAHCHTGNELNOITCESTNEV
lanimoN htgneLnoitceS )sehcni( 621426384T
O
T
A
L
Q
T
Y
noitceSteN )sehcni(htgneL 2/1-42/1-012/1-222/1-432/1-64
tneVfothgieHsnoitceStneVforebmuN
sehcnitf
5.4573.0100001
957.0200002
5.01578.0010001
5152.1110002
5.91526.1210003
1257.1020002
5.22578.1001001
5.52521.2120003
5.13526.2030003
5.43578.2000101
5.73521.3111003
5.34526.3021003
5457.3002002
5.64578.3000011
5.94521.4102003
1552.4100012
5.55526.4012003
7557.4001102
6652.5022004
5.76526.5003003
9657.5000202
276103004
5.37521.6100203
5.97526.6010203
1857.6000112
095.7021014
5.
19526.7002013
3957.7000022
698101204
5.79521.8100023
2015.8200024
5.301526.8000303
8019100304
4115.9020024
71157.9105006
5.811578.9110305
6215.01001304
5.031578.01101305
53152.11006006
8315.11000404
5.931526.11000033
5.241578.11100405
TRAHCHTGNELNOITCESTNEV
noitceSlanimoN )sehcni(htgneL 621426
38
4T
O
T
A
L
Q
T
Y
noitceSteN )sehcni(htgneL 2/1-42/1-012/1-222/1-4
32
/1-64
tneVfothgie
Hs
noitceStneVforebmuN
sehcnitf
44121100034
0515.21010034
5.451578.21110035
5.061573.31020035
5.271573.41000505
77157.41100506
38152.51010506
6815.51000044
5.091578.51100045
5.691573.61010045
5.502521.71011507
70252.71000606
5.112526.71100607
5.712521.81010607
5.922521.91001607
5.232573.91000055
73257.91100056
5.142521.02000707
6425.02100708
25212010708
46222001708
67232000808
97252.32000066
5.082573.32100809
5.382526.32100067
5.982521.42010067
5.103521.52001067
5.013578.52000909
5135.621009001
5.523521.72000077
0335.72100078
63382010078
54357.82000 0
10
01
5.943521.92100 0
10
11
27313000088
5.673573.13100089
5.973526.13000 1
10
11
5.814578.43000099
32452.531000901
56457.83000
0010
1
SV4.5CGV-1
Termination SV4.5FA OR
SV4.5FB Flashing
AND SV4.5SC
STORM COLLAR
*SV4.5VF
Firestop/Spacer
SV4.5L6/12/24/36/48
Vent Sections
40' Max
(12.2 M)
1" (25.4 mm)
Minimum
Clearance to
Combustibles
*When using Secure Flex,
use Firestop/Spacer
SF4.5VF
Effective Vent Length
Model Effective Length
SV4.5L6 4-1/2"
SV4.5L12 10-1/2"
SV4.5L24 22-1/2"
SV4.5L36 34-1/2"
SV4.5L48 46-1/2"
Table 7
Figure 19
See Figure 19 and Figures 29-33 on
Pages 20-21 and their associated
Vertical Vent Tables which illustrate the various
verticalventingconfigurations thatarepossible
forusewiththeseappliances. SecureVent®pipe
applicationsareshownintheseFigures;Secure
®pipe may also be used. A Vertical Vent
Tablesummarizes each system’sminimum and
maximum vertical and horizontal length values
that can be used to design and install the vent
components in a variety of applications.
Both these vertical vent systems terminate
through the roof. The minimum vent height
above the roof and/or adjacent walls is speci-
fied in ANSI Z223.1-(latest edition) (In Canada,
the current CAN/CSA-B149.1 installation code)
by major building codes. Always consult your
localcodes for specificrequirements.A general
guide to follow is the Gas Vent Rule (refer to
Figure 5 on Page 8).
(Figure19)
Determine the number of straight vent sec-
tions required. 4-1/2" (114 mm), 10-1/2" (267
mm), 22-1/2" (572 mm), 34-1/2" (876 mm)
and 46-1/2" (1181 mm) net section lengths
are available (see Tables on this page and
Page 39 - Rigid Vent Sections). Plan the vent
lengths so that a joint does not occur at the
intersection of ceiling or roof joists. Refer to
the Vent Section Length Chart.
18
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
Installation and Operation Instructions
900476-000, 08/2015
Innovative Hearth Products
RochesterTM See Through and Peninsula Direct Vent Gas Fireplace
First Vent
Component
Align the dimple (four places)
with the opening of the locking
incline channel on appliance
collar. Twist vent component
clockwise to engage and seal.
Locking
Incline Channel
Dimple
Appliance collar
Vent / Appliance Collar
Connection
Align the dimple (four places) of the
upper vent section with the opening of
the locking incline channel on the
lower vent section. Twist vent
component clockwise to engage and
seal until arrow and dimple align.
Locking
Incline Channel
Dimple
Arrow
Connected
Vent Sections
Vent / Vent Section
Connection
Arrow
Arrow
Figure 20
Figure 21
Figure 23
Figure 22
C.Attachventcomponentstoeachother-Other
vent sections may be added to the previously
installedsectioninaccordancewiththerequire-
ments of the vertical vent figures and tables.
To add another vent component to a length of
ventrun,alignthedimpledendovertheinclined
channel end of the previously installed section,
adjusting the radial alignment until the four
locking dimples are aligned with the inlets of
thefourinclinechannelsoftheprevioussection.
Push the vent component against the previous
section until it fully engages, then twist the
componentclockwiserunningthedimplesdown
and along the incline channels until they seat at
the end of the channels.This seating position
Figure 22.
D. Install firestop/spacer at ceiling - When
usingSecureVent,useSV4.5VFfirestop/spacer
at ceiling joists; when using Secure Flex, use
SF4.5VF firestop/spacer. If there is living space
abovetheceiling level,thefirestop/spacermust
be installed on the bottom side of the ceiling.
If attic space is above the ceiling, the firestop/
spacer must be installed on the top side of
the joist. Route the vent sections through the
framed opening and secure the firestop/spacer
with 8d nails or other appropriate fasteners at
each corner.
to obtain the required clearances indicated
here. See installation accessories tables on
Pages 39 and 40.
Analyze the vent routing and determine the
quantities of vent sections and number of el-
bows required. Refer to Vertical Vent Figures
and Tables on Page 20 to select the type of
vertical installation desired. Vent sections are
available in net lengths of 4-1/2" (114 mm),
10-1/2" (267 mm), 22-1/2" (572 mm), 34-1/2"
(876 mm) and 46-1/2" (1181 mm). Refer to the
Effective Vent Length Chart on Page 17 for an
aidinselectinglengthcombinations.Elbowsare
available in 90° and 45° configurations. Refer
to Figure 24 for the SV4.5E45 and SV4.5E90
elbow dimensional specifications.
Where required, a telescopic vent section
may be used to provide the installer
withanoption in installing in tight and confined
spaces or where the vent run made up of fixed
length pieces develops a joint in a undesirable
location, or will not build up to the required
length. The SV4.5LA Telescopic Vent Section
has an effective length of from 1-1/2" (38 mm)
to 7-1/2" (191 mm). The SV4.5LA is fitted with
a locking inclined channel end (identical to a
normalventsectioncomponent) andaplainend
with 3 pilot holes. Slip the plain end over the
locking channel end of a standard SV4.5 vent
component the required distance and secure
with three screws.
combustible materials for all vertical elements.
Clearances for all horizontal elements are 3"
A. Frame ceiling opening - Use a plumb line
from the ceiling above the appliance to locate
center of the vertical run. Cut and/or frame an
opening, 10-1/2" x 10-1/2" (267mm x 267mm)
inside dimensions, about this center mark
(Figure 20 ).
To attach a vent component to the appliance
collar, align the dimpled end over the collar,
adjusting the radial alignment until the four
locking dimples are aligned with the inlet of
the four inclined channels on the collar (refer to
Figure 21). Push the vent component against
the collar until it fully engages, then twist the
component clockwise, running the dimples
down and along the incline channels until they
seat at the end of the channels. The unitized
design of the Secure Vent components will
engage and seal both the inner and outer pipe
withouttheneedforsealantorscrews. Ifdesired
a #6 x 1/2" screw may be used at the joint, but
it is not required as the pipe will securely lock
when twisted.
NOTE: An elbow may also be attached to the
appliance collar. Attach in the same manner as
you would a vent section.
B. Attach vent components to appliance -
SecureVent®SV4.5Direct-Ventsystemcompo-
nents are unitized concentric pipe components
featuring positive twist lock connections (see
Figures 21 and 22).
All of the appliances covered in this document
are fitted with collars having locking inclined
channels. The dimpled end of the vent com-
ponents fit over the appliance collar to create
the positive twist lock connection.
Minimum
Clearance to
Combustibles
vSV4.5VF
Firestop / spacer
uSV4.5SP
Support Plate
uSV4.5SU
Support Strap
Shown With
Optional
Radiant
Panels
uSecured
Appropriate
Fasteners
Ceiling
Framing
vWhen
using
secure
Firestop/
Spacer
SF4.5VF
SV4.5FA or
SV4.5FB Flashing
and SV4.5SC
Storm Collar
SV4.5CGV-1
Termination
10-1/2" Min.
10-1/2" Min.
19
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
Installation and Operation Instructions
900476-000, 08/2015
Innovative Hearth Products
RochesterTM See Through and Peninsula Direct Vent Gas Fireplace
Framing Dimensions for Roof
Pitch C D
0/12 10-1/2 in. 10-1/2 in.
(267 mm) (267 mm)
6/12 10-1/2 in. 12 in.
(267 mm) (305 mm)
12/12 10-1/2 in. 17-3/4 in.
(267 mm) (451 mm)
Figure 25
Figure 26
Figure 28
Figure 27
If the vent system extends more than 5' (1.5
m) above the roof flashing, stabilizers may be
necessary. Additional screws may be used at
section joints for added stability. Guide wires
may be attached to the joint for additional sup-
port on multiple joint configurations.
G.Continueinstallationofhorizontal/inclined
sections - Continue with the installation of the
straight vent sections in horizontal/inclined run
as described in Step C. Install support straps
every 5' (1.52 m) along horizontal/inclinedvent
runs using conventional plumber’s tape. It is
very important that the horizontal/inclined
from the fireplace 1/4" per foot (20 mm per
meter) of horizontal vent.Use a carpenter’s
level to measure from a constant surface and
adjust the support straps as necessary.
It is important to maintain the required clear-
the bottom for all horizontal/inclined runs.
F.Changeventdirectiontohorizontal/inclined
run - At transition from or to a horizontal/in-
clined run, install the SV4.5E45 and SV4.5E90
elbows in the same manner as the straight vent
sections. The elbows feature a twist section to
allow them to be routed about the center axis
of their initial collar section to align with the
required direction of the next vent run element.
only so as to avoid the possiblity of unlocking
anyofthepreviouslyconnectedventsections.
See Figure 24.
E. Support the vertical vent run sections -
NOTE: Proper venting supportis very important.
The weight of the vent must not be supported
by the fireplace in any degree.
Support the vertical portion of the venting
system every 8 feet (2.4m) above the fireplace
vent outlet. One method of support is by utiliz-
ing field provided support straps (conventional
plumber's tape). Secure the plumber's tape to
the framing members with nails or screws.
Loop the tape around the vent, securing the
ends of the tape to the framing. If desired,
sheet metal screws #6 x 1/2" length may be
used to secure the support straps to the vent
pipe. See Figure 23.
Figure 24
SV4.5E90
(90
°
Elbow)
8-1/8"
(206 mm)
Swivel Joint
(360
°
swivel)
4-13/16"
(122 mm)
SV4.5E45
(45
°
Elbow)
Swivel Joint
(360
°
swivel)
C
D
Storm
Collar
K. Install the vertical termination - The final
step involves installation of the SV4.5CGV-1
Vertical Termination. Extend the vent sections
to the height as shown in the "Vertical vent ter-
mination section" on Page 8. The SV4.5CGV-1
Vertical Termination (Figure 28 ) installs in the
exact same fashion as any other Secure Vent
section. Align the termination over the end of
the previously installed section, adjusting the
radial alignment until the four locking dimples
of the termination are aligned with the inlets of
thefourinclinechannelsofthelastventsection.
Pushtheterminationdown untilitfullyengages,
thentwistthetermination clockwiserunningthe
dimples down and along the incline channels
until they seat at the end of the channels.
I. Install the roof flashing - Extend the vent
sections through the roof structure. Install the
roof flashing over the vent section and posi-
tion such that the vent column rises vertically
(use carpenters level) (Figure 26 ). Nail along
perimetertosecureflashing oradjust roofingto
overlap the flashing edges at top and sides only
andtrimwherenecessary. Sealthe topand both
sides of the flashing with waterproof caulking.
J. Install the storm collar - Install the storm
collar,suppliedwiththe flashing, over the vent/
flashingjoint. SeeFigure 27. Loosenthe storm
collar screw. Slide collar down until it meets
the top of the flashing. Tighten the adjusting
screw. Apply non-combustible caulking or
mastic around the circumference of the joint
to provide a water tight seal.
H. Frame roof opening - Identify location for
vent at the roof. Cut and/or frame opening per
Roof Framing Chart and Figure 25.
20
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
Installation and Operation Instructions
900476-000, 08/2015
Innovative Hearth Products
RochesterTM See Through and Peninsula Direct Vent Gas Fireplace
VERTICAL VENT FIGURES/TABLES
NOTE: Secure Vent®(rigid vent pipe) is shown
in the figures; Secure Flex®(flexible vent pipe)
may also be used.
NOTE: It is very important that the horizontal/
inclined run be maintained in a straight (no
dips) and recommended to be in a slightly
elevated plane, in a direction away from the
fireplace of 1/4" rise per foot (20 mm per meter)
which is ideal, though rise per foot run ratios
that are smaller are acceptable all the way down
to at or near level.
NOTE:SV4.5VF (Secure Vent),SF4.5VF (Secure
Flex) firestop/spacer must be used anytime vent
pipe passes through a combustible floor or ceil-
ing. SV4.5HF (Secure Vent), SF4.5HF (Secure
Flex)firestop/spacer must be used anytime vent
pipe passes through a combustible wall.
NOTE: Two 45 degree elbows may be used in
place of one 90 degree elbow. The same rise
to run ratios, as shown in the venting figures
for 90 elbows, must be followed if 45 degree
elbows are used.
NOTE: An elbow is acceptable as 1 foot of
vertical rise, except where an elbow is the
only vertical component in the system. (See
Figure 38 on Page 24).
WARNING
-
vent pipe be joined together.
H
V
V1
V
H
Figure 29 - Top Vent - STRAIGHT
Figure 31 - Top Vent - TWO 90 DEGREE ELBOWS
40 feet
uCeiling Firestop /
u
Firestop/Spacer SF4.5VF
uCeiling Firestop /
vWall Firestop/
u
u
Firestop / Spacer SF4.5VF.
v
Firestop / Spacer SF4.5HF.
Example: If 20 feet of (H) hori-
zontal vent run is needed, then 4
feet minimum of (V) vertical vent
will be required.
This table shows a 1(V) to 5(H)
ratio. For every 1 foot of (V) verti-
cal, you are allowed 5 feet of (H)
horizontal run, up to a maximum
horizontal run of 20 feet.
An elbow is acceptable as 1 foot
of vertical rise except where an
elbow is the only vertical compo-
nentin the system. See Figure38.
Table B
V Minimum
feet feet
5
5 1
10 2
15 3
20 4
V + V1
Table A
V Minimum
feet feet
2 1
4 2
6 3
8 4
Ratio V to H ratio is 1:2
u
Spacer SF4.5VF.
Example: If 8 feet of (H) horizontal vent run is needed, then 4 feet minimum (V) vertical vent will be
required.
This table shows a 1(V) to 2(H) ratio. For every 1 foot of (V) vertical, you are allowed 2 feet of (H)
horizontal run, up to a maximum horizontal run of 8 feet.
Figure 30 - Side Vent - ONE 90 DEGREE ELBOW
This manual suits for next models
3
Table of contents
Other Comfortflame Indoor Fireplace manuals
Comfortflame
Comfortflame CTDV36NR-A Quick start guide
Comfortflame
Comfortflame Sonoma18LZN Service manual
Comfortflame
Comfortflame CGFB32CC Safety guide
Comfortflame
Comfortflame Barkley Series User manual
Comfortflame
Comfortflame Oakridge36YBP User manual
Comfortflame
Comfortflame CVSR18 User manual
Comfortflame
Comfortflame B42LI-M Safety guide
Comfortflame
Comfortflame CGCFTNA Quick start guide
Comfortflame
Comfortflame Columbus Series Owner's manual
Comfortflame
Comfortflame CDCFpRB Safety guide
Comfortflame
Comfortflame Westerly32ZMN User manual
Comfortflame
Comfortflame Cumberland32YWS User manual
Comfortflame
Comfortflame CGCFTNA Safety guide
Comfortflame
Comfortflame CUVF36C Quick start guide
Comfortflame
Comfortflame Oxford18LZN User manual
Comfortflame
Comfortflame B42LI-M Operation manual
Comfortflame
Comfortflame CHDV32NR Quick start guide
Comfortflame
Comfortflame CGEFP33NRC User manual
Comfortflame
Comfortflame CGDV32NR (PR)-3 User manual
Comfortflame
Comfortflame Aurora35DEN User manual
Popular Indoor Fireplace manuals by other brands
Pacific energy
Pacific energy ESTEEM Installation and operating instructions
FMI
FMI GL36St OWNER'S OPERATION AND INSTALLATION MANUAL
Sierra Flame
Sierra Flame ABBOT Series Installation and operating instructions
FMI
FMI Baja II 36WIL installation instructions
kozy heat
kozy heat OSSEO 29 Installation and operation manual
RCF
RCF ONYX2 owner's manual
IKOS
IKOS ECOpellets Insert user manual
BIS
BIS Ultima Installation and operating instructions
Global Fires
Global Fires Fantasy RC User instructions
Robinson Willey
Robinson Willey Sahara LF operating instructions
Empire Comfort Systems
Empire Comfort Systems DVCP36PP30N-1 Installation instructions and owner's manual
Empire Comfort Systems
Empire Comfort Systems BF28BMN-4 installation instructions
Thermocet
Thermocet Trimline Series installation instructions
Nu-Flame
Nu-Flame Sparo Instructions for use and safety
Dimplex
Dimplex DIMPLEX ELECTRIC FIREPLACE Practical user's guide
Gasmate
Gasmate ONYX GM142-175 manual
Sunjoy
Sunjoy L-OF082PST-3 Assembly instructions
Superior
Superior WRE3836WS Installation and operation instructions