Commercial Electric 5053-WH User manual

□
□
1
Installation
3
Attach the desired accessory plates (included) inside the box
with the included screws. Use #2 stubby Phillips screwdriver to
install these plates. Note: If you will be running tubing to this
box, choose the cutout size that best suits your needs and cut
the snap-in plate to make the pass-through.
ATTACHING THE DESIRED ACCESSORY PLATES
PREPARING THE WALL FOR INSTALLATION
Installation Guide
TV Multimedia Recessed Box
Item #1001863174
Model #5053-WH
Using the template supplied, trace the opening for the plate on the
wall. Remember, the plate is designed to be mounted centered
between the studs.
TEMPLATE
C
D
E
A
B
2
*This product is designed for standard 2x4 framed walls. If your wall does
not have the standard 3.5” spacing between the drywall you will need to
use a kit that mounts on the front of the wall.
□
CUT DRYWALL FOR PLATE
Using a drywall saw, cut a hole in the drywall the size of the template.
4
Scan Me
TIP: Loop a piece of tape with the sticky side outward to form a circle and
apply it to the back of the template to secure it to the wall.
PACKAGE CONTENTS
A - Recessed Media Box
B - Snap-in cover plate with conduit/pipe knockouts
C - Flexible pass-through accessory plate
TOOLS NEEDED
Drywall saw
Stud Finder
Level
#2 Phillips screwdriver
D - 6-port keystone accessory plate
E - Blank accessory plate
CAUTION Before installing this product, be sure the
electrical power is off at the circuit breaker or
remove fuse(s).
For video information visit homedepot.com and search
SKU 1001863174 or model number 5053-WH
#2 Stubby Phillips
Screwdriver
Pencil
TOOLS NEEDED (Not included)
15 Amp electrical receptacle
Use the stud nder to center between the wall framing studs.
□
Be sure to frame your plate both vertically and horizontally.
□
DETERMINE THE TV MULTIMEDIA RECESSED
BOX LOCATION
Tape
RoHS Compliant
ETL LISTED
CONFORMS TO
UL STD. 514C
CERTIFIED TO
C
AN/CSA STD. C22.2#42.1:200-1
3026001
Rev. 01/29/2019

Installation Guide
TV Multimedia Recessed Box
Item #1001863174
Model #5053-WH
CAUTION: When using tools always follow the
manufacturer’s safety guidelines.
Please read all instructions and safety information before use.
Retain this manual for future reference.
□
6
□
7
Run the source of power to the included old work electrical box by
pushing in one of the tabs to create an opening. Be sure to follow all
local electrical codes. Wire an electrical receptacle (not included) to
the old work electrical box and secure the electrical box to the posts
on the back of the multimedia box using the included screws.
Before installing the Multimedia Box into the template opening,
make sure to pull your low voltage cables through the low voltage
cable opening.
Starting with the receptacle side of the Multimedia Box, slowly
slide it into the opening on the wall. Swing the opposite side of
the Multimedia Box into position until the entire Multimedia Box is
ush with the wall. Secure the screws with wings; these fasten
tightly against the back of the drywall.
CONNECTING THE RECEPTACLE (NOT INCLUDED) INSTALLING THE MULTIMEDIA BOX
Electrical Wire
□ Your new Multimedia Box is now installed and ready for the
TV mount to be installed. Install your TV mount bracket (not
included) per the TV bracket manufacturer’s instructions.
HANG TV AND ENJOY
□
Safety Information
F
A
5
TV
Installation Continued
RoHS Compliant
Rev. 01/29/2019
ETL LISTED
CONFORMS TO
UL STD. 514C
CERTIFIED TO
C
AN/CSA STD. C22.2#42.1:200-1
3026001

Templates
Item #1001863174
Model #5053-WH
TEMPLATE
ACTUAL SIZE
7-5/16”
CUT ALONG DOTTED LINE 
7-1/8”
Conforms to UL Std. 514C
Certified to CSA Std. C22.2#42.1:2000 Ed.1
3026001
RoHS Compliant