Commercial Electric MB-64102 User manual

Soundbar Bracket
for mounting below or
above wall mounted 23" - 65" TVs
MB-64102
********

This mount has been tested to
support a television with diagonal
screen sizes between 23in. and 65in.
(58 cm & 1.65 m) and a weight
up to 33lbs. (15kgs).
1.38"(35mm)
13.78"(350mm)
min3.07"~max18.9"(min78~max480mm)
20"(510mm)
0.98"(25mm)
0.2"(5mm)
0.43"(11mm)
It is the installer's responsibility
to make sure the structure can support the
weight of all equipment. Reinforce the
structure as required before installing the
component.
33 lbs.
(15kgs).
soundbar
soundbar
soundbar bracket
bracket
bracket
Before you begin, carefully read and understand the instructions
in this manual. Please follow the instructions in the order
presented in this manual and observe all warnings and cautions.
4-7

F
10 20 30 40 50 60 70 80 90 100mm
1 2 3 4in
4 each
8 or 4
AA
BB
CC
Screw (size M6x14,M6x20,M8x20,M6x30,M8x30)
Washer 2
Spacer (size Φ15xΦ8x5 and Φ15xΦ8x15)
A
IJ
G
H
E
C
D
B
Bracket 2
2
4
4
A
Extension bracketB
BoltC
D Hex nyloc nut
2
E Screw (size M4x14)
2
F Screw (size M5x14)
2
2
2
2
G
H
I
J
Screw (size M6x14)
Washer
Flat thread fastener
Flange hex lock nut
Pre-Installation

Screw is too
long
Screw ts
correctly
Screw is too
short
AA CC
BB
injuries and property damage, make sure that
there are adequate threads to secure the
brackets to your TV. If you encounter resistance,
stop immediately and contact customer service.
Use the shortest screw and spacer combination
to accommodate your TV. Using hardware that is
too long may damage your TV. However, using
a screw that is too short may cause your TV to
fall from the mount.
To avoid potential personal
CAUTION:

3
Attaching the brackets to soundbar
For small size soundbar：
Use the washers (H) and screws (E/F) to attach the brackets (A,B) to the soundbar with round hole pattern.
Use the flat thread fasteners (I) and flange hex lock nuts (J) to attach the brackets (A,B) to the soundbar
with keyhole pattern.
For large size soundbar:
Connect the brackets (A,B) and extension brackets (B) using the bolts (C) and hex nyloc nuts (D).
Use the screws (G) or the screws (E/F) and washers (H) to attach the brackets to the soundbar with
round hole pattern.
Use the flat thread fasteners (I) and flange hex lock nuts (J) to attach the brackets to the soundbar
with keyhole pattern.
C
D
G
E/F
H
J
I
E/F
HJ
I
G
Installation (continued)

1
2
1
2
For large size soundbar:
An extra TV mount is required.
Attach the TV mounting arms and soundbar brackets to the four holes on the back of the
TV as shown.
K
R
1
K
2
P
R
L/M
1
L/M
P
2
P
L/M
R
1
L/M
P
2
N/O
Q
R
1
Q
N/O
2
N/O
P
R
Q
1
N/O
P
Q
2
K
1
R
K
2
P
R
L/M
1
L/M
P
2
P
L/M
R
1
L/M
P
2
N/O
Q
R
1
N/O
Q
2N/O
P
Q
2
R
N/O
P
Q
1
4
For small size soundbar:
An extra TV mount is required.
Attach the TV mounting arms and the brackets (A) to the four holes on the back of the TV as shown.
Attaching the soundbar to the TV
Installation (continued)

5
Hanging the TV on the TV mounting plate
Installation (continued)