Comnet NWKBB100 Owner's manual

INSTALLATION AND OPERATION MANUAL
Industrial DC-Battery Power Management System
Thank you for purchasing NetWave® from ComNet. This manual
will cover how to install hardware on your enclosure, configure
batteries, cabling, and mounting of the enclosure.
The NetWave® NWKBB100 DC-Battery Power Solution provides
consistent power for your devices in locations where power
is on a timer or they have frequent blackouts or brownouts.
The NWKBB100 supports AC input ranging from 110 to 277
VAC, and can also support higher voltages using a Step Down
Transformer. The intelligent controller distributes power to the
load and batteries when AC power is available and instantly
switches over to DC output only when AC power is lost. The kit
includes valve-regulated lead-acid batteries, outdoor enclosure,
mounting bracket and Smart DC-Battery Power Controller. The
aluminum outdoor enclosure has two 180° door hinges and
a pad lockable latch for security. The enclosure has built in
mounting brackets that support pole and wall mounting.
This manual serves the following
ComNet Model Numbers:
NWKBB100

INS_NWKBB100_REV– 06/10/13 PAGE 2
INSTALLATION AND OPERATION MANUAL NWKBB100
TECH SUPPORT: 1.888.678.9427
About This Guide
This guide is intended for different users such as engineers, integrators, developers, IT managers,
and technicians.
It assumes that users have some PC competence and are familiar with Microsoft Windows
operating systems and web browsers such as Windows Internet Explorer and Mozilla Firefox, as
well as have knowledge of the following:
»Installation of electronic equipment
»Electrical regulations and guidelines
»Knowledge of Local Area Network technology
Related Documentation
The following documentation is also available:
»NWKBB100 Datasheet
Website
For information on ComNet’s entire product line, please visit the ComNet website at
http://www.comnet.net
Support
For any questions or technical assistance, please contact your sales person ([e-mail]) or
the customer service support center ([e-mail])
Safety
»Only ComNet service personnel can service the equipment. Please contact ComNet Technical
Support.
»The equipment should be installed in locations with controlled access, or other means of
security, and controlled by persons of authority.

INS_NWKBB100_REV– 06/10/13 PAGE 3
INSTALLATION AND OPERATION MANUAL NWKBB100
TECH SUPPORT: 1.888.678.9427
Contents
About This Guide 2
Related Documentation 2
Website 2
Safety 2
Overview 5
Legal Information 5
1.0 Introduction 6
2.0 Installation 7
Preparing the Enclosure 7
Mounting the Enclosure 8
Battery Configuration 9
3.0 Controller Configuration 10

INS_NWKBB100_REV– 06/10/13 PAGE 4
INSTALLATION AND OPERATION MANUAL NWKBB100
TECH SUPPORT: 1.888.678.9427
Overview
Legal Information
No part of this document may be reproduced or transmitted in any form or by any means,
electronic and mechanical, for any purpose, without the express written permission of ComNet.
Copyright
Copyright © 2016 Communication Networks, LLC (dba ComNet). All rights reserved.
Disclaimer
ComNet reserves the right to make changes in specifications at any time without notice. The
information furnished by ComNet in this material is believed to be accurate and reliable. However,
ComNet assumes no responsibility for its use.

INS_NWKBB100_REV– 06/10/13 PAGE 5
INSTALLATION AND OPERATION MANUAL NWKBB100
TECH SUPPORT: 1.888.678.9427
1.0 Introduction
The NetWave® NWKBB100 DC-Battery Power Solution provides consistent power for your devices
in locations where power is on a timer or they have frequent blackouts or brownouts.
The NWKBB100 supports AC input ranging from 110 to 277 VAC, and can also support 347 VAC
and 480 VAC with an optional Multi Tap Power Transformer. The intelligent controller distributes
power to the load and batteries when AC power is available and instantly switches over to DC
output only when AC power is lost.
The kit includes valve-regulated lead-acid batteries, outdoor enclosure, mounting hardware and
Smart DC-Battery Power Controller. The aluminum outdoor enclosure has a gasket hinged lid
with one tamper proof lock operated by a special key for high security. The enclosure has built in
mounting brackets that support pole and wall mounting.
This manual contains detailed operational and configuration information.

INS_NWKBB100_REV– 06/10/13 PAGE 6
INSTALLATION AND OPERATION MANUAL NWKBB100
TECH SUPPORT: 1.888.678.9427
2.0 Installation
Preparing the Enclosure
The NWKBB100 enclosure has integrated mounting brackets and a bolt on mounting plate simplifying
installation.
Prepare the mounting plate for DIN Rail installation by loosening the screws in the top corners and
removing the mounting plate (the appearance of the included mounting plate may vary).
Place the DIN Rail in its desired location. If the pre drilled holes do not align, use a 5/32 drill bit to
create a new mounting location.
Secure the DIN Rail to the mounting plate using the provided Screw, Washer and Nut.
Re-attach the mounting plate to the enclosure and tighten bolts.

INS_NWKBB100_REV– 06/10/13 PAGE 7
INSTALLATION AND OPERATION MANUAL NWKBB100
TECH SUPPORT: 1.888.678.9427
Mounting the Enclosure
The NWKBB100 has rackmounts welded onto the enclosure for ease of installation.
The included hose clamps will allow you to mount the enclosure on up to a 3 inch diameter pole
or you can wall mount the unit using screws appropriate to your mounting surface.

INS_NWKBB100_REV– 06/10/13 PAGE 8
INSTALLATION AND OPERATION MANUAL NWKBB100
TECH SUPPORT: 1.888.678.9427
Battery Configuration
One the DIN Rail has been installed and the enclosure has been mounted, setup the batteries.
We provide four 12VDC batteries that will need to be configured in series since our controller will
output 48VDC.
Batteries in Series:
Connect the unterminated end of the Negative wire to port 3 on the controller
Connect the unterminated end of the Positive wire to port 4 on the controller
Note: The controller will not power on till AC power source is detected.
To start the controller on battery power you will need to connect an RTCONN Cable to a switch to
jump start it. Cable is not provided.

INS_NWKBB100_REV– 06/10/13 PAGE 9
INSTALLATION AND OPERATION MANUAL NWKBB100
TECH SUPPORT: 1.888.678.9427
3.0 Controller Configuration
The Uninterruptible power supply can be used in many different applications.
We recommend the following settings for the NWKBB100 Kit.
Leave the Charging Current set to 50%.
Set Jump settings to Sealed Lead High.
Jumpers are on the bottom right of the controller.

INS_NWKBB100_REV– 06/10/13 PAGE 10
INSTALLATION AND OPERATION MANUAL NWKBB100
TECH SUPPORT: 1.888.678.9427
Connect your device to the 48VDC @ 5A power source on Pins 1 and 2.
Connect AC Power Source to the Controller
Once AC power is detected, the LEDs on the front of the controller will light up.
Mains or Backup LED will be off when AC power is available and on when powered by the battery.
Low Battery or Battery Replacement LED indicates that the battery is below 30% capacity or will
stay on if a battery fault is detected.
The Diagnosis LED indicates charging mode.
1 Blink/Sec for Trickle Charge
2 Blink/Sec for Boost Charge
5 Blink/Sec for Recovery Charge
More detailed instructions will be provided with the controller for all other applications.

INS_NWKBB100_REV– 06/10/13 PAGE 11
INSTALLATION AND OPERATION MANUAL NWKBB100
TECH SUPPORT: 1.888.678.9427

INS_NWKBB100_REV– 06/10/13 PAGE 12
INSTALLATION AND OPERATION MANUAL NWKBB100
TECH SUPPORT: 1.888.678.9427
© 2018 Communications Networks Corporation. All Rights Reserved. “ComNet” and the “ComNet Logo” are registered trademarks of Communication Networks, LLC.
3 CORPORATE DRIVE | DANBURY, CT 06810 | USA
T: 203.796.5300 | F: 203.796.5303 | TECH SUPPORT: 1.888.678.9427 | [e-mail]
8 TURNBERRY PARK ROAD | GILDERSOME | MORLEY | LEEDS, UK LS27 7LE
T: [phone] | F: [phone] | [e-mail]
ComNet Customer Service
Customer Care is ComNet Technology’s global service center, where
our professional staff is ready to answer your questions at any time.
Email ComNet Global Service Center: customercar[email protected]
Contact Information
ComNet – www.comnet.net
North America ComNet Corporate Headquarters
and Customer Support Center
Te l: +1- 203 -796 - 53 0 0
Tel: [phone]
Email: [e-mail]
EMEA, PACRIM,
South America ComNet Europe Ltd, Leeds
Tel: [phone]
Tel: [phone]
Email: [e-mail]