Compaq Evo W6000 Setup guide

System Unit
1 Access panel Not spared
2 Front bezel assembly 239066-001
3 Chassis/basepan Not spared
4Power supply, PFC, dual voltage 202348-001
*Not shown
Mass Storage Devices
118.2-GB U3 SCSI hard drive (10000 rpm) 229737-001
*18.2-GB U3 SCSI hard drive (15000 rpm) 194585-001
*18.4-GB U3 SCSI hard drive (15000 rpm) 293127-001
*36.2-GB U3 SCSI hard drive (10000 rpm) 192197-001
*20-GB UATA hard drive (7200 rpm) 180475-001
*40-GB QUIET hard drive (10000 rpm) 202904-001
*80-GB UATA hard drive (7500 rpm) 250185-001
*32X Max CD-RW drive, carbon 232315-001
*CD-RW drive, 32X/10X/40X, S2, carbon 283919-001
*DVD-RAM, drive, 4.7-GB, carbon 232318-001
*Zip drive, 250-MB, carbon 232317-001
2Diskette drive, 3.5-inch, buttonless, carbon 237180-001
348X CD-ROM drive, carbon 232320-001
*Not shown
Documentation and Packaging (not illustrated)
Illustrated Parts Map 235551-001
Service Reference Guide 259968-001
Quick Troubleshooting Guide 153837-001
Shipping box with buns 244890-001
Cables
1 CD-ROM audio cable, 21” 149806-001
2 Diskette drive cable, 18” 221186-001
*# IDE dual connection, 18”, 13.75” between system
board and connector 1 225881-001
*# IDE dual connection, 18”, 13.75” between system
board and connector 1 239064-001
* IDE dual connection, 18”, 12” between system board
and connector 1 224484-001
* SCSI cable w/twist, three-device 158277-001
* G200 Quad, analog cable 12” lg, 2 ea. 168754-001
with retaining washer (for use with Matrox G200
MMS graphics board #171975-001)
171976-001
* Power switch assembly, includes power switch and
cable, and switch mounting bracket 166925-001
* Cable kit, contains: 254551-001
* G200 quad, analog cable 12” lg (168754-001)
* G200 quad, digital cable 72” lg (168754-002)
Cable kit includes 166879-002
* Diskette drive cable with twist, 11” (143218-001)
* 40-position IDE data cable, 12.5” (105876-001)
* IDE Ultra ATA dual device, hard drive/CD-ROM
cable, 18”, with pull tab, center polarization
(108950-007)
* Dual-LED power cable (1 ea.) (387727-001)
* Switch mounting bracket (3 ea.) (1666777-001)
* Diskette drive/tape cable, with twist, 34”
(356107-001)
* Diskette drive cable with twist, 11” (387795-001)
* Not shown
# Cables are interchangeable
Miscellaneous Screw Kit (not illustrated)
Miscellaneous Screw Kit, includes: 179180-001
6-32 x 1/4 hi-top, thread-forming screw with serrations (4 ea.)
(192308-001)
6-32 x 3/16 hi-top, thread-forming screw with serrations (5 ea.)
(192308-003)
6-32 x 3/16 buttonhead tamper-resistant, taptite screw with serrations
(4 ea.) (296769-002)
6-32 x 5/16 hi-top, taptite screw (5 ea.) (109834-568)
6-19 x 5/16 panhead, plastite screw (5 ea.) (101346-068)
6-19 x 5/16 hi-top, taptite screw with captive washer (4 ea.)
(114399-069)
6-19 x 1/2 Panhead, plastite screw (4 ea.) (101346-071)
M3 x 5mm, hi-top, taptite screw with serrations (3 ea.) (247348-001)
Thumbscrew, molded cap (179333-002)
Standard and Optional Boards (not illustrated)
System Board, 2P (also replaces 239059-001) 254545-001
Intel Xeon Processor
1.4-GHz with 256 KB cache 239060-001
1.5-GHz with 256 KB cache 239061-001
1.7-GHz with 256 KB cache 239062-001
2.0 GHz with 256 KB cache 253072-001
1.8 GHz with 512 KB cache # 278543-001
2.0 GHz with 512 KB cache # 278544-001
2.2 GHz with 512 KB cache # 278545-001
2.4 GHz with 512 KB cache # 284645-001
2.6 GHz with 512 KB cache # 303015-001
2.8 GHz with 512 KB cache# 307548-001
Heatsink with alcohol pad and thermal grease
to 1.8 GHz (replaces 239111-001) 255354-001
2.0 GHz and above 284440-001
Memory Module, 800MHz
RDRAM, 128-MB 157112-001
RDRAM, 256-MB 161454-001
RDRAM, 512-MB 239067-001
CRIMM (2 ea.) 158265-001
Graphics Controllers
nVidia Quadro2 Pro, 64-MB, AGP/AT 225829-001
nVidia Quadro2 MXR Graphics Board 221492-001
Matrox G200 MMS Graphics Board 171975-001
Matrox 450 32MB AGP Graphics Board 203626-001
Matrox G550 AGP Graphics Board 253275-001
Network Interface Controller (NIC) 10/100 118042-001
PCI USB Controller (NA only) 291001-001
PCI USB Controller (Rest of World) 300866-001
# Requires 1.15 or later system BIOS to recognize the cache.
Miscellaneous Parts (not illustrated)
Diskette drive adapter (for bay 3 use only) 239063-001
Fan, 92-mm 239065-001
Baffle and baffle insert 260613-001
Battery 153099-001
Mouse, 3-button, carbon 232616-001
Mouse, carbon 165000-001
Keyboards (not illustrated)
Easy Access Keyboard 164996-xxx
Arabic -171 International -B31
Belgian -181 Latin American
Spanish -161
Brazilian -201 Norwegian -091
*BHCSY -B41 Polish -B31
Czech -221 Portuguese -131
Danish -081 Russian -251
Dutch/Netherlands -B31 Slovakian -231
Finnish -351 Spanish -071
French -051 Swedish -101
French Canadian -121 Swiss -111
German -041 Taiwanese -AB1
Greek -151 Thai -281
Hungarian -211 Turkish -141
Italian -061 UK -031
Japanese -191 US -001
Korean (Hanguel) -AD1
*Bosnia-Herzegovina, Croatia, Slovenia, and Yugoslavia
Miscellaneous Plastics Kit (* not illustrated)
Miscellaneous Plastics Kit, includes: 166878-001
1 Panel, sub (166835-001) (not this product)
2 Bezel, blank (166775-001) (not this product)
3 Diskette drive bezel (166776-001)
4 Card guide (166778-001)
5 Foot, rubber (4 ea.) (166939-002) (not this product)
6 Button, power (166774-001) (not this product)
7 Drivelock, DT (166779-001)
8 Spring, power button (166837-001) (not this product)
9 Springs, drivelock (2 ea.) (166837-002)
10 Drivelock, MT (166780-001)
* Retention mechanism (2 ea.) (350767-001)
Miscellaneous Plastics Kit, includes: 238687-001
1 Panel, sub (166835-012)
2 Bezel, blank (166775-002)
5 Foot, rubber, (8 ea) (166939-004)
b
© 2002 Compaq Information Technologies Group, L.P.
Compaq, the Compaq logo, and EVO are trademarks of Compaq
Information Technologies Group, L.P.
Intel and Pentium are trademarks of Intel Corporation.
All other product names mentioned herein may be trademarks of
their respective companies.
Compaq shall not be liable for technical or editorial errors or
omissions contained herein. The information in this document is
provided “as is” without warranty of any kind and is subject to
change without notice. The warranties for Compaq products are
set forth in the express limited warranty statements
accompanying such products. Nothing herein should be
construed as constituting an additional warranty.
September 2002
Document Number
235178-005
Spare Part Number
235551-001
Compaq Evo Workstation
W6000
Illustrated Parts Map

Connectors and Jumpers
J20-22 Three 32-bit, 33-MHz PCI Sockets P12 Alert-On-LAN (AOL) Connector
J37 Ultra 160 SCSI Connector P20 Primary Ultra ATA Connector
J40 AGP Pro Socket P21 Secondary Ultra ATA Connector
P1 24-Pin Power Supply Connector P34 Power-On Password Enable Jumper
P2 6-Pin Power Supply Connector SW2 Smart Cover Sensor
P5 Power Switch Connector SW50 CMOS Reset Switch
P6 Internal Speaker Connector VRM Embedded Voltage Regulator Module
P7 Audio Connector XBT1 Battery
P8 Rear Fan Connector XMM1-2 Channel A RIMM Socket
P9 Wake-On-LAN Connector (WOL) XMM3-4 Channel B RIMM Socket
P10 Diskette Drive Connector XU1 Primary Processor Socket
P11 CD-ROM Audio Connector XU2 Secondary Processor Socket
System Hardware Interrupts (PIC Mode)
IRQ System Function IRQ System Function
0Timer Interrupt 8 System CMOS/Real-Time Clock
1Keyboard 9 Unused
2Unused 10 Standard USB controller 2
Intel PRO/100 VM embedded NIC
3Serial Port (COM 2) 11 Adaptec AIC-7892 embedded SCSI controller
Standard USB controller 1
4Serial Port (COM 1) 12 Mouse
5Video Controller
Creative ES1371/1373 embedded audio 13 NumericDataProcessor
6Diskette Drive 14 Primary ATA (IDE) Controller
7Parallel Port (LPT 1) 15 Secondary ATA (IDE) Controller
System Hardware Interrupts (IO APIC Mode)
IRQ System Function IRQ System Function
0System Timer 12 Mouse
1Keyboard 13 NumericDataProcessor
2Unused 14 Primary IDE Controller
3Serial Port (COM 2) 15 Secondary IDE Controller
4Serial Port (COM 1) 16 Unused
5Unused 17 Creative ES1371/1373 embedded audio
6Diskette Drive 18 Video controller
7Parallel Port (LPT 1) 19 Standard USB controller 2
8System CMOS/Real-Time Clock 20 Intel PRO/100 VM embedded NIC
9ACPI-compliant system 21 Unused
10 Unused 22 Adaptec AIC-7892 embedded SCSI controller
11 Unused 23 Standard USB controller 1
Computer LEDs (On front of computer)
LED Color LED Activity State/Message
Power Green On (S0) Computer on
Power Green 1 blink every 1 second (S1) Normal Suspend Mode
Power Green 1 blink every 2 seconds (S3) Suspend to RAM
Power Green 1 blink every 4 seconds (S4) Suspend to Disk (if applicable)
Power Clear Off (S5) Computer off
Power Red 2 blinks 1 second apart, fol-
lowedby2-secondpause-
Repeat
CPU thermal shutdown
Power Red On CPU not installed
Power Red 1 blink every 1 second ROM error
Power Red 1 blink every 2 seconds Power supply crow bar
Hard Drive Green Blinking Hard drive activity
ROM BIOS
Use ROM BIOS 686P8, ver 01.22, dated 6-26-02 or later.
Keyboard Diagnostic LEDs
LED Color LED Activity State/Message
Num Lock Green Flashing (Beeps - 1S, 2L) Memory error
Caps Lock Green Flashing (Beeps - 1L, 2S) No video
Scroll Lock Green Flashing (Beeps - 2L, 1S) System board failure, prior to video
Num, Caps,
Scroll Lock Green Flash On-Off 2 times (Beeps - 1L, 3S) Invalid system ROM detected. ROM forces reflash.
Num, Caps,
Scroll Lock Green On (Rising Tone) ROM reflashed successfully
Num Lock Green On ROMPaq diskette not present, is bad, or drive
not ready.*
Caps Lock Green On Enter password.
Num, Caps,
Scroll Lock Green Blink On in sequence, one at a time - N, C, SL Keyboard locked in network mode
* Insert valid ROMPaq diskette in drive A. Turn power switch off, then on to reflash ROM. If ROM flash is successful, all
three keyboard LEDs will light up, and you will hear a rising tone series of beeps. Remove diskette and turn power off,
then on to restart the computer. For more information about flashing the ROM, refer to the Troubleshooting guide.
System Board Diagnostic Lights1
Main Power
Switch Status 3.3 V_Aux LED 5 V_Aux/PSON LED Power Button LED
OFF2ON ON4OFF
ON3ON OFF5ON
1. ON and OFF state of LEDs apply only to a good, working system board with AC power applied to the power supply.
2. Power LED on front of computer is OFF.
3. Power LED on front of computer is ON (Green).
4. 5V_Aux is ON.
5. PSON is active = power supply is turned ON.
Integrated Network Interface (NIC) Diagnostic Lights (on back of computer)*
LED Color on RJ-45 Connector LED Activity State/Message
Green ON Network link
Green Flashing Network activity
Amber ON 100 Mb Connection
Amber OFF 10 Mb Connection
*Applies only to NICs that are an integral part of the system board.
Computer Setup (F10) Utility Features (not all features may be available)
File
System Information
About
Set Time and date
Save to Diskette
Restore From Diskette
Set defaults and Exit
Ignore Changes and Exit
Save Changes and Exit
Storage
Device Configuration
Options
IDE DPS Self-Test
Controller Order
SCSI Narrow Termination
Boot Order
Security
Setup Password
Power-On Password
Password Options
Smart Cover
Smart Sensor
DriveLock
Master Boot Record Security
Save Master Boot Record
Restore Master Boot Record
Device Security
Network Service Boot
System IDs
Power Energy Saver Timeouts
Energy Saver Options
Advanced
Power-On Options
Onboard devices
PCI Devices
Bus Options
Devise Options
PCI VGA Configuration
Note: See Computer Setup (F10) Utility Guide on the Documentation Library CD.
Clearing CMOS
The computer's configuration (CMOS) may occasionally be corrupted. If it does, it is necessary to clear the CMOS
memory using switch SW50.
To clear and reset the configuration, perform the following procedure:
1. Prepare the computer for disassembly.
ÄCAUTION: The power cord must be disconnected from the power source before pushing the Clear CMOS
Button (NOTE: All LEDs on the board should be OFF). Failure to do so may damage the system board
2. Remove the access panel.
3. Press the CMOS button located on the system board and keep it depressed for 5 seconds.
4. Replace the access panel.
5. Turn the computer on.
6. Run F10 Computer Setup (delete-utility) to reconfigure the system.
Disabling or Clearing the Power-On and Setup Passwords
1. Turn off the computer and any external devices, and disconnect the power cord from the power outlet.
2. Remove the access panel.
3. Locate the header and jumper labeled P34.
4. Remove the jumper from pins 1 and 2. Place the jumper over pin 2 only, in order to avoid losing it.
5. Replace the access panel.
6. Reconnect the external equipment.
7. Plug in the computer and turn on power. Allow the operating system to start. This clears the current passwords and
disables the password features.
8. To re-enable the password features, repeat steps 1-4, then replace the jumper on pins 1 and 2.
9. Repeat steps 6-8, then establish new passwords.
Refer to the Computer Setup (F10 Setup) instructions to establish new passwords.