Compatible Brands CB24WINEDUAL User manual

Write the Serial Number here:
_________________________
BUILT-IN TWO-ZONE WINE COOLER
Models CB24WINEDUAL
Owner’s Manual
BEFORE USE, PLEASE READ AND FOLLOW
ALL SAFETY RULES AND OPERATING INSTRUCTIONS

1
TABLE OF CONTENTS
Important Safety Instructions ................................................................2 – 3
Location of Parts ...........................................................................................4
Installation Instructions ..........................................................................5 – 7
Before Using Your Wine Cooler ............................................................5
Installation of Your Wine Cooler ..................................................... 5 - 6
Reversing the Door Swing .............................................................. 6 - 7
Operating Your Wine Cooler ................................................................8 – 10
Recommended Temperatures for Chilling Wine ...................................8
Control Panel ........................................................................................8
ON/OFF Power .....................................................................................8
RUN Light .............................................................................................8
Setting the Temperature Control ...................................................... 8 - 9
Interior Light .........................................................................................9
Door Lock .............................................................................................9
Defrosting .............................................................................................9
Storage of Wine Bottles ......................................................................10
Care and Maintenance ........................................................................10 – 12
Cleaning Your Wine Cooler ................................................................10
To Remove a Sliding Shelf .................................................................11
Replacement of the LED Light ............................................................11
Power Failure .....................................................................................11
Vacation Time .....................................................................................11
Transporting Your Wine Cooler .....................................................11 -12
Energy-Saving Tip ..............................................................................12
Technical Information .................................................................................12
Problems with Your Wine Cooler ...............................................................13
Limited Warranty .........................................................................................15

2
IMPORTANT SAFETY INSTRUCTIONS
WARNING To reduce the risk of fire, electrical shock or injury when
using your appliance, follow these basic precautions
•Read all instructions before using the wine cooler.
•Plug into a grounded 3-prong outlet. Do not remove grounding prong, do not use an adapter,
and do not use an extension cord.
•It is recommended that a separate circuit, serving only your wine cooler, be provided. Use
receptacles that cannot be turned off by a switch or pull chain.
•Never clean wine cooler parts with flammable fluids. These fumes can create a fire hazard or
explosion.
•Before proceeding with cleaning and maintenance operations, make sure the power line of the
unit is disconnected.
•Do not connect or disconnect the electric plug when your hands are wet.
•Unplug the wine cooler or disconnect the power before cleaning or servicing. Failure to do so
can result in electrical shock or death.
•Do not attempt to repair or replace any part of your appliance unless it is specifically
recommended in this manual. All other servicing should be referred to a qualified technician.
•Do not store or use gasoline or any other flammable vapors and liquids in the vicinity of this or
any other appliance. The fumes can create a fire hazard or explosion.
•Use two or more people to move and install the wine cooler. Failure to do so can result in
back or other injury.
•To ensure proper ventilation for your appliance, the front of the unit must be completely
unobstructed. Choose a well-ventilated area with temperatures above 61°F (16°C) and below
95°F (35°C). This unit must be installed in an area protected from the elements, such as wind,
rain, water spray or drips.
•The wine cooler should not be located next to ovens, grills or other sources of high heat.
•For optimum energy conservation, locate the wine cooler in the coolest area of the room, away
from heat- producing appliances and out of direct sunlight.
•The wine cooler must be installed with all electrical connections in accordance with state and
local codes. A standard electrical supply (115V AC only, 60 Hz), properly grounded in
accordance with the National Electrical Code and local codes and ordinances, is required.
•Do not kink or pinch the power supply cord of the appliance.
•The fuse (or circuit breaker) size should be 15 amps.
•It is important for the wine cooler to be leveled in order to work properly. You may need to
make several adjustments to level it.
•Although the unit has been tested at the factory, due to transit and storage, you should clean

3
the appliance before use.
•Do not use solvent-based cleaning agents or abrasives on the interior. These cleaners may
damage or discolor the interior.
•Do not use this apparatus for other than residential purposes.
•This appliance is CFC- and HFC-free and contains small quantities of Isobutane (R600a)
which is environmentally friendly, but flammable. It does not damage the ozone layer, nor does
it increase the greenhouse effect. Care must be taken during transportation and setting up of
the appliance that no parts of the cooling system are damaged. Leaking coolant can ignite and
may damage the eyes.
In the event of any damage:
- Avoid open flames and anything that creates a spark,
- Disconnect from the electrical power line,
- Air the room in which the appliance is located for several minutes, and
- Contact the Service Department for advice.
•The more coolant there is in an appliance, the larger the room it should be installed in. In the
event of a leakage, if the appliance is in a small room, there is the danger of combustible gases
building up. For every ounce of coolant at least 325 cubic feet of room space is required. The
amount of coolant in the appliance is stated on the data plate on the back of the appliance. It is
hazardous for anyone other than an Authorized Service Person to carry out servicing or repairs
to this appliance.
•Take serious care when handling, moving, and using the appliance to avoid either damaging
the refrigerant tubing or increasing the risk of a leak.
•Replacing component parts and servicing shall be done by factory-authorized service
personnel so as to minimize the risk of possible ignition due to incorrect parts or improper
service.
•This appliance is designed to be used in household and similar non-retail applications. Do not
use this appliance for any but its intended purpose.
DANGER! Risk of child entrapment
Child entrapment and suffocation are not problems of the past. Junked or abandoned
appliances are still dangerous, even if they will “just sit for a few days”.
•Before you throw away your old wine cooler or any appliance: Remove the door.
Leave the shelves in place so that children may not easily climb inside.
•Never allow children to operate, play with, or crawl inside the appliance.
- SAVE THESE INSTRUCTIONS -

4
LOCATION OF PARTS
1. Control panel
2. Large shelf in upper zone
3. Air-duct board
4. Large shelf in lower zone
5. Small shelf in lower zone
6. Lock hook
NOTE: This wine cellar has a carbon filter installed in the rear wall of the cabinet.
This filter improves air purity and cooling efficiency, and helps maintain an
odor-free environment for the stored wine. We recommend that the filter be
changed every 12 months.
7. Door support
8. Adjustable foot
9. Upper hinge
10. Door (with handle and gasket)
11. Lower hinge
12. Lock
13. Front vent

5
INSTALLATION INSTRUCTIONS
Before Using Your Wine Cooler
Remove the exterior and interior packing.
Before connecting the wine cooler to the power source, let it stand upright for
approximately 2 hours. This will reduce the possibility of a malfunction in the
cooling system from handling during transportation.
Clean the interior surface with lukewarm water using a soft cloth.
This appliance is especially designed for the storage of wine; do not use it for other
purposes.
Installation of Your Wine Cooler
This appliance is designed for free standing or built-in (fully recessed) installation.
If free standing, the unit should have at least 4” of clearance at both sides, at the
top and at the back to allow for adequate ventilation.
If the appliance is to be built-in, leave at least 3/16” at both sides, 1/16” at the top
and 2” at the rear. Be sure that airflow under the appliance is not blocked. The
diagram below shows the correct dimensions for under-counter installation:
Place your wine cooler on a floor that is strong enough to support it when it is fully
loaded. To level your wine cooler, adjust the leveling legs at the bottom of the unit.
Locate the wine cooler away from direct sunlight and sources of heat (stove, heater,
radiator, etc.). Direct sunlight may affect the exterior surface and heat sources may
increase electrical consumption. Extremely cold or warm ambient temperatures
23.62”
23.43”
23.62”
(min)
33.27”
3.54”
33.86”
(min)

6
may also cause the unit to perform improperly.
Avoid locating the unit in moist areas. Do not use an extension cord.
Plug the wine cooler into an exclusive, properly installed and grounded wall outlet.
Do not under any circumstances cut or remove the third (ground) prong from the
power cord. Any questions concerning power and/or grounding should be
directed toward a certified or authorized products service center.
Reversing the Door Swing
This appliance has the capability of the door opening from either the left or right
side. The unit is delivered to you with the door opening from the left side. Should
you desire to reverse the opening direction, please follow these illustrations and
instructions:

7
NOTE: All parts removed must be saved to allow the door swing to be reversed
1. Carefully use a sharp tool to pry up the decorative cap on the top of the cabinet
and the cap of the door spindle. (Fig 1)
2. Open the door about 90°, unscrew the screw of the upper door hinge cover and
remove the cover, then unscrew all the screws on the upper door hinge. Be sure
to hold the door firmly after removing the screws, and take off the door. (Fig 2)
3. Remove the screw of the lower door hinge, door support and the left side screw
of the front vent (Fig 3), then install the lower door hinge and lower door support
at the designated position on the opposite side. (Fig 4)
4. Remove the screw of the door handle, then remove the bottom screw on the left
side of the door and remove the lower support of the door (Fig 5). Install the
lower support of the door on the opposite side. (Fig 6).
5. Gently pull open the middle section of the door gasket; you will see the handle
screw hole (Fig 7). Remove the handle and install it on the opposite side.(Fig 8)
6. Loosely install the upper door hinge on the opposite side. (Fig 9)
7. Set the door onto the shaft of the lower door hinge (Fig 10), then fit the shaft of
the upper door hinge into the top of the door (Fig 11) and tighten the screws.
Adjust the door so it is aligned with the cabinet. Level the cabinet and tighten all
the lock screws.
You also can call customer service for door reversal instructions if necessary.

8
OPERATING YOUR WINE COOLER
The wine cooler should be placed where the ambient temperature is between 61
and 95 degrees Fahrenheit (16-35°C). If the ambient temperature is above or
below this range, the performance of the unit may be affected. For example,
placing your unit in extremely cold or hot conditions may cause interior
temperatures to fluctuate and the range of 41-72 degrees Fahrenheit (5-22°C) may
not be reached.
Recommended Temperatures for Chilling Wine
Red Wines: 58-65°F (14-18°C)
Dry / White Wines 48-57°F (9-14°C)
Sparkling Wine 40-47°F (4-8°C)
Temperatures inside the unit may vary slightly depending on whether or not the
interior light is ON or OFF or whether the bottles are located on the upper/middle
or lower section.
Control Panel
ON/OFF Power
Connect the power cord to a properly grounded outlet. To turn the appliance on or
off, press the ON/OFF button.
NOTE: This wine cooler has a protective delay function. The compressor will start
to work about 3 to 5 minutes after it is powered on.
RUN Light
This light indicates when the compressor is working. While the compressor is
operating, the red light is on. During down time in the operating cycle, this light is
off.
Setting the Temperature Control
Each cooling chamber of the wine cooler (upper and lower) is independently
controlled.
Set the desired cooling temperature by pressing one of the SET buttons. Each
depression of the button will scroll through the available temperature settings (for
each chamber) in increments of 1 degree. The temperature selected will flash in
the LED display for approximately 5 seconds, then the display will revert back to

9
the internal cabinet temperature. The SET temperature is automatically saved.
Upper chamber: Temperature setting can be adjusted from 41 to 54°F (5 to 12°C).
Lower chamber: Temperature setting can be adjusted from 54 to 72°F (12 to 22°C).
To view the SET temperature of either chamber at any time, press the
corresponding SET button. The SET temperature will show in the LED display
for about 5 seconds, then the current internal temperature for that chamber will
reappear.
In the event of a power interruption, all previous temperature settings are
automatically saved and each chamber will keep the previous temperature setting.
(The temperature preset at the factory is 41°F (5°C) for the upper chamber and
54°F (12°C) for the lower chamber.)
This unit has the option to display temperatures in either Fahrenheit or Celsius. To
change the setting, press the °C/°F button. A green light will indicate whether
Fahrenheit or Celsius temperatures are being displayed.
NOTES: If the unit is unplugged or turned off, or if there is a power failure, you
must wait 3 to 5 minutes before restarting the unit. If you attempt to restart
before this time delay, the wine cooler will not start.
When you use the wine cooler for the first time, or restart the wine cooler after
it has been shut off for a long time, there could be a few degrees variation
between the temperature you select and the one indicated on the LED readout.
This is normal and is due to the length of the inactivation time. Once the wine
cooler has been running for a few hours, it should operate normally.
Interior Light
You can turn the interior light on or off by pushing the button marked LIGHT. For
best storage of wine, keep the light off except when viewing.
NOTE: The light goes off automatically after 10 minutes.
Door Lock
This unit can be secured with a lock and key. The keys are located inside the plastic
bag that contains the User’s Manual. Insert the key into the lock and turn it
clockwise to lock the door, making sure the metal pin is engaged completely. To
unlock the door, do the reverse. Remove the key and put it in a secure location.
Defrosting
The wine cooler defrosts automatically during its operating cycle. The water
resulting from the defrosting is collected in a drip tray near the compressor at the
back where it is automatically evaporated. During the defrosting operation, the
displayed temperature may be higher than the set temperature.

10
Storage of Wine Bottles
Your wine cooler was designed to store a maximum of 44 bottles in total security.
We recommend that you observe the tips below to optimize loading:
•Each of the four large shelves can hold 8 bottles, and the two smaller shelves
can each hold 6 bottles, arranged as shown here:
•Spread your bottles out as evenly as possible over the shelves, so that weight
is not concentrated in one spot. Also make sure your bottles do not touch the
back of the cabinet or the step at the bottom of the lower chamber.
•Make sure that bottles are not all grouped together at the top or bottom of the
cabinet.
•Never stack more than one layer of bottles on a sliding shelf.
•Never try to pull out more than one sliding shelf at a time.
CARE AND MAINTENANCE
Cleaning Your Wine Cooler
1. Turn off the power, unplug the appliance, and remove all items including shelves.
(See “To Remove a Sliding Shelf” below.).
2. Wash the inside surfaces with a warm water and baking soda solution. The
solution should be about 2 tablespoons of baking soda to a quart of water.
3. Wash the shelves with a mild detergent solution.
4. Wring excess water out of the sponge or cloth when cleaning the area near the
controls, or any electrical parts.
5. Wash the outside cabinet with warm water and a mild liquid detergent. Rinse
well and wipe dry with a clean soft cloth. Clean the stainless steel trim with a
product specifically designed for this use.
Large shelf
Small shelf
rear wall
rear wall

11
To Remove a Sliding Shelf
1. Remove all bottles from the shelf.
2. Pull the shelf out as far as it will go.
3. Adjust the lever on each side of the shelf, as shown below (down on the left, up
on the right) and at the same time, pull the shelf out completely.
To raise or lower the position of the shelf, push up the sliding rails, making the front
hook out of the shelf bracket, then pull the sliding rails outward to detach them
from the shelf bracket. Reverse these steps to install rails in new location.
Replacement of the LED Light
Replacing the LED requires a qualified technician. First unscrew the 2 screws on
the light cover, then remove the screw on the LED panel, and replace the light with
one having the same specifications.
Power Failure
Most power failures are corrected within a few hours and should not affect the
temperature of your appliance if you minimize the number of times the door is
opened. If power is going to be off for a longer period of time, you need to take
the proper steps to protect the contents of your wine cooler.
Vacation Time
Leave the wine cooler operating during vacations of less than three weeks. For
periods longer than this, turn the wine cooler off and leave the door slightly ajar to
prevent odor from building inside the appliance.
Transporting your Wine Cooler
If you need to move your wine cooler once the box has been discarded:
1. Securely tape down all loose items (shelves) inside your appliance.
2. Turn the adjustable legs up to the base to avoid damage.

12
3. Tape the door shut.
4. Be sure the appliance stays secure in the upright position during transportation.
Also protect the outside of the appliance with a blanket or similar item.
Energy-Saving Tip
The wine cooler should be located in the coolest area of the room, away from heat
producing appliances and out of direct sunlight.
TECHNICAL INFORMATION
Volume
5.43 cu.ft. (154 liters)
Bottle Capacity
44
Rated Voltage
110V AC
Rated Current
0.5A
Power Input
70W
Rated Frequency
60Hz
Refrigerant
R160a (30g, or 1 ounce)
Sound Level (db)
43
Climate Type
N
Net Weight
112 lbs (51kg)
Gross Weight
121 lbs (55kg)
Defrost Type
Automatic

13
PROBLEMS WITH YOUR WINE COOLER
You can solve many common wine cooler problems easily, saving you the cost of
a possible service call. Try the suggestions below to see if you can solve the
problem before calling a service technician.
TROUBLESHOOTING GUIDE
Problem
Possible Cause
Wine cooler does not
operate.
Not plugged in.
The appliance is turned off.
The circuit breaker has tripped or a fuse has blown.
Wine cooler is not
cold enough.
Check the temperature control settings.
External environment may require higher settings.
The door is opened too often.
The door is not closed completely.
The door gasket does not seal properly.
Turns on and off
frequently.
The room temperature is hotter than normal.
A large number of bottles has been added to the
wine cooler.
The door is opened too often.
The door is not closed completely.
The temperature controls are not set correctly.
The door gasket does not seal properly.
The light does not
work.
Not plugged in.
The circuit breaker has tripped or fuse is blown.
The bulb has burned out.
The LIGHT button is off.
Vibrations
Check to be sure the wine cooler is level.
Wine cooler seems to
be making too much
noise.
Some noise may come from the flow of the
refrigerant, which is normal.
As each cycle ends, you may hear gurgling sounds
caused by the flow of refrigerant in your wine
cooler.
Contraction and expansion of the inside walls may
cause popping and crackling noises.
The wine cooler is not level.
The door will not
close properly.
The wine cooler is not level.
The door was reversed and not properly installed.
The gasket is dirty.
The shelves are out of position.
This appliance is intended to be used exclusively for the storage of wine.

14
NOTES

15
LIMITED WARRANTY
ONE-YEAR LIMITED WARRANTY
Within the 48 contiguous United States, for one year from the date of purchase, when this appliance is
operated and maintained according to instructions attached to or furnished with the product, Appliance World
will pay for factory-specified parts and repair labor to correct defects in materials or workmanship. Service
must be provided by a designated service company. Outside the 48 states, all parts are warranted for one
year from manufacturing defects. Plastic parts, shelves and cabinets are warranted to be manufactured to
commercially acceptable standards, and are not covered from damage during handling or breakage.
5-YEAR COMPRESSOR WARRANTY
1. The compressor is covered for 5 years.
2. Replacement does not include labor.
ITEMS WARRANTOR WILL NOT PAY FOR:
1. Service calls to correct the installation of your appliance, to instruct you how to use your appliance, to
replace or repair fuses or to correct wiring or plumbing.
2. Service calls to repair or replace appliance light bulbs or broken shelves. Consumable parts (such as
filters) are excluded from warranty coverage.
3. Damage resulting from accident, alteration, misuse, abuse, fire, flood, acts of God, improper installation,
installation not in accordance with electrical or plumbing codes, or use of products not approved by
warrantor.
4. Replacement parts or repair labor costs for units operated outside the United States.
5. Repairs to parts or systems resulting from unauthorized modifications made to the appliance.
6. The removal and reinstallation of your appliance if it is installed in an inaccessible location or is not
installed in accordance with published installation instructions.
DISCLAIMER OF IMPLIED WARRANTIES;LIMITATION OF REMEDIES
CUSTOMER'S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS
PROVIDED HEREIN. IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR
A PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR. WARRANTOR SHALL NOT BE LIABLE FOR INCIDENTAL OR
CONSEQUENTIAL DAMAGES. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR
CONSEQUENTIAL DAMAGES, OR LIMITATIONS ON THE DURATION OF IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS, SO THESE EXCLUSIONS OR LIMITATIONS MAY NOT APPLY TO YOU. THIS
WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS, WHICH VARY FROM
STATE TO STATE.
WARNING: This product can expose you to chemicals including Nickel
(Metallic) which is known to the State of California to cause cancer.
For more information go to www.P65Warnings.ca.gov
Note: Nickel is a component in all stainless steel and some other metallic compositions.
FOR SERVICE, PLEASE CALL 718-893-3900 ext. 599