Comtrend Corporation PoE-9213 User manual

1
Quick Installation Guide
PoE-9213 | Single-Port Gigabit Ethernet Extender
Product Information
I-1. Package Contents
PoE-9213 PoE Extender
Mounting accessory
Foot Pads
Quick Installation Guide
I-2. Product Overview
I
Front
Back
PoE Out:
Use this port to
plug in your
PoE-Enabled Device
(Support IEEE802.3af output)
PoE In:
Use this port to plug in
a PoE Switch or PoE
Injector
(Support IEEE802.3at input)

2
Ethernet Cable
PoE-9213
PoE Switch
Quick Setup
Attach an Ethernet cable from the “PoE In” port of the PoE+
Extender to either a PoE Switch or PoE Injector.
Attach an Ethernet cable from the “PoE Out” port of the PoE+
Extender to the PoE- Enabled device.
Congratulations, you are done!
FOR MORE HELP: For instructions on features, FAQ, etc., please visit our online
Product Webpage for the PoE-9213.
For more information:
YouTube: https://www.youtube.com/user/ComtrendConnection
Facebook: https://facebook.com/Comtrend
Website: http://us.comtrend.com/
Support: Visit our website or call 1-877-COMTREND (1-877-266-8736)
II
PoE-9213
PoE- Enabled Device
(Access Point, IP Camera, etc.)
III

3
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
4. Consult the dealer or an experienced radio technician for help.
EMC Warning
This equipment complies with EU radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with minimum distance 20cm between the radiator & your
body.
Safety
1. This product is designed for indoor use only; DO NOT install the adapter outdoors.
2. DO NOT put this product at or near hot or humid places, e.g. kitchen or bathroom. DO NOT use
any spray or liquids on it.
3. DO NOT touch the product with wet hands and DO NOT clean the product with a wet cloth.
Use a soft, dry cloth to clean the device.
4. DO NOT expose the product to lit candles, cigarettes, open flames, high or low temperatures,
etc.
5. DO NOT pull any connected cable with force; disconnect it from the power first.
6. Ensure proper ventilation, so that air flows freely around the product.
7. If you find that the product is not working properly, please contact your dealer of purchase and
ask for help. Do NOT open the casing
8. DO NOT disassemble the product, warranty will be void.

4
Supplier’s Declaration of Conformity
We
Company: Comtrend Corporation - North America
Address: 14 Chrysler, Irvine, CA, 92618
Certify and declare under our responsibility that the following equipment:
Product Name: Single-Port PoE Gigabit Ethernet Extender
Model Name: PoE-9213
Brand Name: COMTREND
Is tested with the declaration described above, and is in conformity with the relevant FCC (Federal Communication
Commission) standards, and technical specifications have been applied:
EMC:
47 CFR FCC Rules and Regulations Part 15 Subpart B, Class BDigital Device
Class B :
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
Notes:
15.19(a)(3) Regulations :
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired
operation.