Comtrend Corporation GS-7608 User manual

Quick Installation Guide
GS-7608 | 8-Port PoE Gigabit Ethernet Smart-Lite Switch
Product Information
I-1. Package Contents
1. GS-7608 PoE Switch
2. QIG
3. Power Cable
4. 4 x Foot Pads
5. Rack-Mount Kit
1
2
3
4
5
I

2
I-2. Hardware Overview
Front Panel
The front panel of the switch consists of:
8 x 10/100/1000Mbps RJ-45 Ports
oPorts 1-8 are PoE Capable
oPorts 9-10 are SFP transceiver Capable
A Series of LED Indicators
Rear Panel
The rear panel of the switch features the AC power connector
(DC IN 53V / 2.83A)
I-3. LED Indicator
Power/SYS:
LED Status
Mode
Description
Green
On
Power on
Blinking
System boot-up
Off
Off
Power off or fail

3
Link/ACT:
LED Status
Mode
Description
Green
On/Blinking
1000Mbps
connected/data
transmitting
Amber
On/Blinking
10/100Mbps
connected/data
transmitting
Off
Off
Disconnected or fail
PoE Max:
LED Status
Mode
Description
Green
On
PoE power output is over
120W PoE power budget
Off
Off
PoE power output is
under 120W PoE power
budget
PoE:
LED Status
Mode
Description
Green
On
PoE power output is on
Off
Off
PoE power output is off
SFP port:
LED Status
Mode
Description
Green
On
1000Mbps connected
Blinking
Data transmitting
Off
Off
Disconnected or fail
I-4. Desktop Installation

4
Install the switch on a desktop by attaching the cushioning rubber
feet to the bottom corners of the switch to protect against
external vibration. Allow adequate space for ventilation between
the device and any objects around.
I-5. Rack-mounting Installation
The switch can be mounted in an EIA standard-sized 19-inch rack
that can be placed in a wiring closet with other equipment. To
install the switch, please follow these steps:
1. Attach the mounting brackets on the switch’s side panels
(one on each side) and secure them with the screws
provided.
Bracket Installation

5
2. Use the screws provided with the equipment rack to mount
the Switch on the rack and tighten it.
Rack Installation
Quick Setup
II-1. Switch to End Device
1. Connect the switch to local power with the included power
cable.
2. Use a standard Cat 5/5e Ethernet cable to connect the switch
to end devices as shown below. Switch ports will automatically
adjust to the link rate of the device to which it’s connected.
Optionally, any port can be used to uplink to an existing network.
Application Diagram
Gateway
VoIP
Phone
IP
Camera
Access
Point
Switch
II

6
II-2. Login
1. Open a web browser and go to the switch’s IP address.
2. Enter the access point’s default IP address 192.168.169.1 into
the URL bar of a web browser.
3. You will be prompted for a username and password. Enter the
default username “admin” and the default password “admin”.
4. You will arrive at the switch configuration window as shown
below:

7
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment andreceiver.
3. Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
4. Consult the dealer or an experienced radio technician forhelp.
EMC Warning
This equipment complies with EU radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
Safety
1. This product is designed for indoor use only; DO NOT install the adapter outdoors.
2. DO NOT put this product at or near hot or humid places, e.g. kitchen or bathroom. DO NOT use
any spray or liquids on it.
3. DO NOT touch the product with wet hands and DO NOT clean the product with a wet cloth. Use a
soft, dry cloth to clean the device.
4. DO NOT expose the product to lit candles, cigarettes, open flames, high or low temperatures, etc.
5. DO NOT pull any connected cable with force; disconnect it from the power first.
6. Ensure proper ventilation, so that air flows freely around the product.
7. If you find that the product is not working properly, please contact your dealer of purchase and
ask for help. Do NOT open the casing
8. DO NOT disassemble the product, warranty will be void.
FOR MORE HELP: For instructions on advanced features, FAQ, etc., please visit
our online Product Webpage.
Your Device is Now Connected!
For more information:
YouTube: https://www.youtube.com/user/ComtrendConnection
Facebook: https://facebook.com/Comtrend
Website: http://us.comtrend.com/
Support: Visit our website or call [phone]
III
V
v
s
d
s
d

8
Supplier’s Declaration of Conformity
We
Company: Comtrend Corporation - North America
Address: 14 Chrysler, Irvine, CA, 92618
Certify and declare under our responsibility that the following equipment:
Product Name: 8-Port PoE Gigabit Ethernet Smart-Lite Switch
Model Name: GS-7608
Brand Name: COMTREND
Is tested with the declaration described above, and is in conformity with the relevant FCC (Federal
Communication Commission) standards, and technical specifications have been applied:
EMC:
47 CFR FCC Rules and Regulations Part 15 Subpart B, Class BDigital Device
Class B :
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
Notes:
15.19(a)(3) Regulations :
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired
operation.