Conair FLX-128 Assembly instructions

Setup Sourcing (Reverse Regrind)
WARNING: This card provides only basic troubleshooting
and maintenance information. Users must be familiar with all
safety information and procedures described in the FLX-128
User Guide.
To Enable a Device
Turn on main power to the FLX-128. Wait for the
Home screen to be displayed.
Press the Devices button then choose
which device group you would like to
access.
Press the Device you would like to
enable.
Press the
Enable
device
button.
2
1
Enable Devices
NOTE: In order to enable devices and utilize all the functionality of the
FLX-128 control, all installation and setup instructions explained in
the User Guide must be completed.
The Reverse Regrind system is used as a way to unload a series of bins attached to a common loader. In this system, rather than sensing a
demand for material (empty bin), the multi-source loader senses a full bin and removes material to evacuate that bin. Multiple grinder bins can be
unloaded sequentially. To begin:
1Press the Device button and choose a device group.
2Choose a device to establish as a multi-source loader. Configure
that device as a multi-source loader.
3Press the Device button, choose a device group for the grinder.
4Configure each grinder (valve) as a grinder and
assign it to the multi-source loader. Now each
grinder that is assigned to the multi-source loader will appear on its net-
work. (Proper login is required.)
Basic Operation
Quick Card
QCC020-0213
<<<
FLX-128
Central Loading
Control
3
4
Corporate Office: 724.584.5500
Instant Access 24/7 (Parts and Service): 800.458.1960
International: 814.437.6861 • www.conairgroup.com
Device Configuration
To Configure Each Device
1Press the Devices button, followed by the device
group you would like to access.
2Press the device you would like to configure.
3Press the Setup button on the screen. This will
allow you to access the Device Configuration
screen. (Proper login is required.)
See the
Operation section of the FLX-128 User Guide for
more information on Security.
4Choose which features and options you would like to enable.
Depending on your configurations, this could include the Fill Alarm,
Material Check, Purge, Discharge, Priority Load, Ratio configuration, and
other settings.
Each device is configured individually. Proper login is required. From the
Individual Device screen press the Setup button. Depending upon I/O configu-
rations, some loader configurations may not be available.
NOTE: The location that multi-source loader is conveying to must be open and
available in order to start unloading the grinder bins.
<<<

The FLX-128 control panel
Login / Logout
To Log In:
The user will have to log in for operator actions or screens which require
security. Once logged in, the user will remain logged in until either the
user logs out or the login times out (10 minutes.)
1Apply power to the machine.
Allow the control to power up.
2Press the Security Level/Login
button.
3Enter the username for your
user level.
See the Operation
section of the FLX-128 User
Guide for more information on
Security.
4Enter the password for your
user level. Once you have suc-
cessfully logged in, your security
level will be displayed as a num-
ber in the Security Level/Login
button.
To Log Out:
Once you are done changing settings, or if you are moving away from the
FLX control, we recommend that you log out so that changes to settings
can not be made by others.
1Press the Security Level/Login button.
2Leave the Username blank and press enter.
3Leave the Password blank and press enter. The user level will
return to “default” or zero.
Using the keypad
When using the controller, at times you are prompted to input numbers or
words. When a keypad opens, you can make your inputs. Note that the
entry will not be accepted until you press the green enter arrow. Use the
shift button to access other symbols available for use. Use the blue
delete arrow to delete selections.
WARNING: This card provides only basic troubleshooting and maintenance information. Users MUST be familiar with all safety information and procedures
described in the FLX-128 User Guide.
QCC020-0213
Home button
Go to the Home screen.
Setup button
Go to the Setup screen.
Individual devices
or equipment
Displays the selec-
table individual pieces
of equipment, with
their current operating
status. (demand,
load, dump, etc.)
Screen name
Indicates the current
screen displayed.
Alarms button
Go to the Alarms area.
Back/Previous
Page button
Goes back to the
previous page you
were on.
Pump Network button
Go to the Pump Network
screen.
ARM Control button
Go to the ARM control
screen.
Previous/Next buttons
Go to the previous or next
screen.
Start and Stop
Use these buttons to
turn the pump (or
other device) on or
off.
Help Overview button
Help for the current screen.
Device Selection button
Go to the Device Selection
screen.
NOTE: Depending on which options you have enabled, and what equipment you have con-
nected to the FLX, your screens and icons may not appear exactly as shown on this screen
and in this QuickCard.
<<<
Setting Up a Device (loader, valve, etc.)
1Press the Setup button to view the Setup screen.
2Press the Device Setup button to view the
Device Setup screen.
3Press the black box beside the device
number and use the pop up keypad to name
this device.
4Press the device number to begin to set
up this device.
5Choose the selections to
set up your individual
device. First the device
type, followed by the assign-
ment, output options, demand
and fill inputs.
6Press Accept.
Setting Up a Pump Name and Type
1Press the Setup button to view the Setup screen.
2Press the Pump Names/Type button to
view the Device Setup screen.
3Press the black box beside the
pump number and use the pop up
keypad to name this pump.
4Press the Pump Type button to set
the type of pump for each pump.
5Press the Back button. This will take you back to
the previous screen where you can name additional
pumps, or navigate to other screens.