Concept LED Lights V-PIX Vision Bar User manual

V-PIX™
Vision Bar
LED Pixel Bar Light
User Manual
KEEPTHIS MANUAL FOR FURTURE NEEDS

1. Unpacking
Thank you for choosing our Vision Bar. For your own safety please read this manual
before installing the device. This manual covers the important information on
installation and applications. Please install and operate the fixture with following
instructions. Meanwhile, please keep this manual for future needs.
The LED pixel bar light is made of a new type of high temperature strength of
engineering Glass with aluminum casing. The fixture is designed and manufactured
strictly following CE Standards. Complying with international standard DMX512
protocol. It is available independently controlled and linkable with each other for
operation. And it is applicable for large-scale live performances, theatre, studio,
nightclubs and discos.
The LED pixel bar adopts 14pcs 3W with the option of either Cool or Warm White
LEDs and 56pcs RGB 3in1 5050 SMD LEDs which features high brightness and
stability. Please carefully unpack it when you receive the fixture and check whether it
is damaged during the transportation. Please check whether the following items are
included inside the box:
LED Pixel Bar Light: 1
User Manual: 1
Power Cable: 1
2. Technology Parameter:
Power Supply:AC110-220V, 50/60Hz
Power Consumption: 100W
Light Source: 14pcs 3W cool or warm white LEDs, 56pcs 5050 RGB 3in1 LEDs

LED Life: 100,000hrs
Control Mode: DMX512, Master/Slave, Auto, Sound active
DMX Channels: 6/8/12/60CH
Feature: Each LED can be controlled alone, Color Chase effect
IP Rate: IP20
Power connector: PowerCon in/Out
Working Position: Any safe working position
Size: 1000 * 70 * 100mm
Net Weight: 2.66Kg
3. Safety Instructions
This device has left the factory in perfect condition. In order to maintain this
condition and to ensure a safe operation, It is absolutely necessary for the user to
follow the safety instructions and warning notes written in this user manual
If the device has been exposed to temperature changes due to environmental changes,
do not switch it on immediately. The arising condensation could damage the device.
Leave the device switched off until it has reached room temperature.
This device falls under protection-class I. It is essential that the device be earthed.
The electric connection must carry out by qualified person.
The device shall only be used with rate voltage and frequency.
Make sure that the available voltage is not higher than stated at the end of this
manual.

Make sure the power cord is never crimped or damaged by sharp edges. If this occurs,
replacement of the cable must be done by an authorized dealer.
Always disconnect from the mains when the device is hot in use or before cleaning it.
Only handle the power cord by the plug. Never pull out the plug by tugging the power
cord.
During initial start-up some smoke or smell may arise. This is a normal process and
does not necessarily mean that the device is defective. It should decrease gradually.
Please don’t project the beam onto combustible substances.
Fixtures cannot be installed on combustible substances. Keep more than 50cm
distance with wall for smooth air flow. Do not obstruct fan to allow maximum
cooling.
If the external flexible cable or cord of bar is damaged it should be replaced by the
manufacturer or his service agent or a similar qualified person in order to avoid a
hazard.
4. Operation Instructions
Don’t turn on the fixture if it’s been through sever temperature difference like after
transportation because it might damage the light due to the environment changes.
Make sure to operate the fixture until it is in normal temperature.
Avoid strong shaking during any transportation or movement.
Don’t expose the fixture to overheating, moisture or environments with too much dust
when installing it. And don’t lay any power cables on the floor or it might cause
electronic shock to the people
Make sure the installation place is in good safety condition before installing the
fixture
Make sure to put the safety chain and check whether the screws are screwed properly
when installing the fixture.

Make sure the lens’are in good condition. It’s recommended to replace the units if
there are any damages or severe scratch.
Make sure the fixture is operated by qualified personnel who knows the fixture before
using
Keep the original packages for if any second shipment is needed.
Don’t try to change the fixtures without any instruction by the manufacturer or the
appointed repairing agencies.
It is not in warranty range if there are any malfunctions from not following the user
manual to operate or any illegal operation like shock short circuit, electronic shock,
lamp broke, etc
5. Mounting And installation
Cautions: For added protection mount the fixtures in areas outside walking paths,
seating areas, or in areas were the fixture might be reached by unauthorized
personnel.
Before mounting the fixture to any surface, make sure that the installation area can
hold a minimum point load of 10 times the devices’ weight.
Fixture installation must always be secured with a secondary safety attachment, such
an appropriate safety cable.
Never stand directly below the device when mounting, removing, or servicing the
fixture from a ceiling, or set on a flat level surface. Be sure this fixture is kept at least
1.5m(1.5ft) away from any flammable materials (decoration etc).
Always use and install the supplied safety cable as a safety measure to prevent
accidental damage and/or injury in the event the clamp fails.
Mounting Points: Overhead mounting requires extensive experience, including
amongst others calculating working load limits, a fine knowledge of the installation
material being used, and periodic safety inspection of all installation material and the
fixture. If you lack these qualifications, do not attempt the installation yourself

improper installation can result in injury.
Be sure to complete all rigging and installation procedures before connecting the main
power cord to the appropriate wall outlet.
Clamp Mounting: The Pixel Bar Light provides a unique mounting bracket assembly
that integrates the bottom of the base and the safety cable rigging point in one unit.
For additional safety be sure to attach at least one properly rated safety cable to the
fixture using one of the safety cable rigging point integrated in the base assembly.
Regardless of the rigging option you choose for your Pixel Bar Light, always be sure
to only use the designated rigging point for the safety cable and never secure a safety
cable to a carrying handle.
DMX-512 control connections
Connect the provided XLR cable to the female 3-pin XLR output of your controller
and the other side to the male 3-pin XLR input the Pixel Bar Light. You can chain
multiple bar lights together through serial linking. The cable needed should be two
core screened cable with XLR input and output connectors. Please refer to the
diagram below.
DMX-512 connection with DMX terminator.
For installation where the DMX cable has to run a long distance or is in an electrically
noisy environment, such as in a discotheque, it is recommended to use a DMX
terminator. This helps in preventing corruption of the digital control signal by
electrical noise. The DMX terminator is simply an XLR plug with a 120Ω resistor
connected between pins 2 and 3, which is then plugged into the output XLR socket of

the last fixture in the chain. Please see illustrations below.
6. Menu Instruction
Press “MENU” to browse the different function, press “ENTER” to Next Menu
(Sub-Menu) Press “UP” or “DOWN” to choose the desire function and Press
“ENTER” to confirm. Press “MENU” to return back last menu.
No.
MENU
Value
Function
1
Addr
1-512
DMX Address Set
2
Chnd
6ch/8ch/12ch/60ch
DMX Channel select
3
SLnd
Mast
SL 1
SL 2
Master / Slave select
4
SoUn
Su 0-59
Sound Control Mode, 0-59 built-in
program
Se 00-99
Sound sensitive 0-99(99 is the most
Sensitive)
5
Auto
Au 0-59
Auto Mode, 0-59 Built-in program

DMX Channels:
6Channels
Channel
Value
Function
1
0-255
Red Dimmer 0-100%
2
0-255
Green Dimmer 0-100%
3
0-255
Blue Dimmer 0-100%
4
0-255
Warm White Dimmer 0-100%
5
Color Chase
000-007
No function
008-12
Color chase 1
13-16
Color chase 2
17-20
Color chase 3
Sp 1-9
Auto Running Speed select 1-9
6
Colo
Co 1-15
Color choose
7
Manu
Red 0-255
Gree 0-255
Blue 0-255
Whit 0-255
Manual mode
8
DISP
dISP
dSIP
Display reverse
9
Ver
V10
Version Number

21-24
Color chase 4
......
......
227-247
Color chase 59
248-255
Sound controlled strobe
6
0-255
Speed control slow-fast
8Channels
Channel
Value
Function
1
0-255
Dimmer 0-100%
2
0-255
Strobe
3
0-255
Red Dimmer 0-100%
4
0-255
Green Dimmer 0-100%
5
0-255
Blue Dimmer 0-100%
6
0-255
Warm White Dimmer 0-100%
7
Color Chase
000-007
No function
008-12
Color chase 1
13-16
Color chase 2
17-20
Color chase 3
21-24
Color chase 4
......
......
227-247
Color chase 59
248-255
Sound controlled strobe
8
0-255
Speed control slow-fast

12Channels
Channel
Value
Function
1
0-255
Dimmer 0-100%
2
0-255
Strobe
3
0-255
Part 1Red Dimmer 0-100%
4
0-255
Part 1 Green Dimmer 0-100%
5
0-255
Part 1 Blue Dimmer 0-100%
6
0-255
Part 1 Warm White Dimmer 0-100%
7
0-255
Part 2 Red Dimmer 0-100%
8
0-255
Part 2 Green Dimmer 0-100%
9
0-255
Part 2 Blue Dimmer 0-100%
10
0-255
Part 2 Warm White Dimmer 0-100%
11
Color Chase
000-007
No function
008-12
Color chase 1
13-16
Color chase 2
17-20
Color chase 3
21-24
Color chase 4
......
......
227-247
Color chase 59
248-255
Sound controlled strobe

12
0-255
Speed control slow-fast
60Channels
Channel
Value
Function
1
0-255
Dimmer 0-100%
2
0-255
Strobe
3
0-255
Group 1 Red Dimmer 0-100%
4
0-255
Group 1 Green Dimmer 0-100%
5
0-255
Group 1 Blue Dimmer 0-100%
6
0-255
Warm White 1 Dimmer 0-100%
.
.
.
.
.
.
.
.
.
55
0-255
Group 14 Red Dimmer 0-100%
56
0-255
Group 14 Green Dimmer 0-100%
57
0-255
Group 14 Blue Dimmer 0-100%
58
0-255
Warm White 14 Dimmer 0-100%
59
Color Chase
000-007
No function
008-12
Color chase 1
13-16
Color chase 2
17-20
Color chase 3
21-24
Color chase 4
......
......
227-247
Color chase 59
248-255
Sound controlled strobe

60
0-255
Speed control slow-fast
8. Troubleshooting
Following are a few common problems that may occur during operation. Here are
some suggestions for easy troubleshooting:
A. The unit does not work, no light and the fax does not work
1. Check the connection of power and main fuse
2. Measure the mains voltage on the main connector
3. Check the power on LED
B. Not responding to DMX Controller
1. DMX LED should be on. If not, check DMX connectors, cables to see if link
properly
2. If the DMX LED is on and no response to the channel, check the address settings
and DMX polarity
3. If you have intermittent DMX signal problems, check the pins on connectors or on
PCB of the unit or the previous one.
4. Try to use another DMX controller
5. Check if the DMX cables run near or run alongside to high voltage cables that may
cause damage or interference to DMX interface circuit.
C. Some units don’t respond to the easy controller
1. You may have a break in the DMX cabling, Check the LED for the response of the
master/slave mode signal
2. Wrong DMX address in the unit, Set the proper address.

D. No response to the sound
1. Make sure the unit does not receive DMX signal
2. Check microphone to see if it is good by tapping the microphone.
9. Maintenance and Cleaning
The following points have to be considered during the inspection:
1) All screws for installing the devices or parts of the device have to be tightly
connected and must not be corroded
2) There must not be any deformations on the housing, color lenses, fixations and
installation spots (ceiling, suspension, trussing)
3) Mechanically moved parts must not show any traces of wear and must not rotate
with unbalances
4) The electric power supply cables must not show any damage, material fatigue or
sediments
Further instructions depending on the installation spot and usage have to be adhered
by a skilled installer and any safety problems have to be removed
In order to make the lights in good condition and extend the life time. We suggest a
regular cleaning to the lights
1) Clean the inside and outside lens each week to avoid the weakness of the lights due
to accumulation of dust.
2) Clean the fan each week.
3) A detailed electric check by approved electrical engineer each three month, make
sure that the circuit contacts are in good condition, prevent the poor contact of circuit

from overheating.
We recommend a frequent cleaning of the device. Please use a moist, lint-free cloth.
Never use alcohol or solvents.
There are no serviceable parts inside the device. Please refer to the instructions under
“Installation Instructions”. Should you need any spare parts, please order genuine
parts from your local dealer.