Condair Omega Pro User manual

Humidication and Evaporative Cooling
2588792-B EN 2002
OPERATION MANUAL
Steam generator
Condair Omega Pro

Thank you for choosing Condair
Installation date (MM/DD/YYYY):
Commissioning date (MM/DD/YYYY):
Site:
Model:
Serial number:
Proprietary Notice
This document and the information disclosed herein are proprietary data of Condair Group AG. Neither this docu-
ment, nor the information contained herein shall be reproduced, used, or disclosed to others without the written
authorisation of Condair Group AG, except to the extent required for installation or maintenance of recipient's
equipment.
Liability Notice
Condair Group AG does not accept any liability due to incorrect installation or operation of the equipment or due
to the use of parts/components/equipment that are not authorised by Condair Group AG.
Copyright Notice
© Condair Group AG, All rights reserved.
Technical modications reserved

3Contents
Contents
1 Introduction 5
1.1 To the very beginning 5
1.2 Notes on the operation manual 5
2 For your safety 7
3 Product Overview 9
3.1 Construction Condair Omega Pro steam generator 9
3.2 Functional description 10
3.3 System overview SPA cabin humidication 11
3.4 System overview direct room humidication 12
4 Operation 13
4.1 First-time commissioning 13
4.2 Display and operating elements 13
4.3 Commissioning after an interruption of operation 14
4.4 Notes on operation 15
4.4.1 Inspections during operation 15
4.4.2 Remote operating and fault indication 15
4.4.3 Draining of the steam cylinder 16
4.4.4 Flushing the Condair RO-A water supply system 16
4.4.5 Performing a complete ushing of the Condair RO-A system 17
4.5 Taking the unit out of operation 17
5 Operating the control software 18
5.1 Standard operating display 18
5.1.1 Operating status indication 19
5.1.2 Maintenance and malfunction indications 19
5.2 Navigating/Operating the control software 20
5.3 Information functions 21
5.3.1 Accessing support informations 21
5.3.2 Accessing system informations 21
5.4 Conguration 26
5.4.1 Accessing the "Conguration" submenu 26
5.4.2 Activating/deactivating and conguration of options – "Features" submenu 26
5.4.3 Control settings – "Control Settings" submenu 34
5.4.4 Basic settings – "General" submenu 39
5.4.5 Communication settings – "Communication" submenu 40
5.5 Maintenance functions 44
5.5.1 Accessing the "Service" submenu 44
5.5.2 Performing maintenance functions – "Service" submenu 44
5.5.2.1 Input diagnostic functions – "Input Diagnostics" submenu 46
5.5.2.2 Relay diagnostic functions – "Relay Diagnostics" submenu 48
5.6 Administration settings 48
5.6.1 Accessing "Administrator" submenu 48
5.6.2 Switching on/off password protection and software updates function -
submenu "Administrator" 49

4Contents
6 Maintenance 50
6.1 Important notes on maintenance 50
6.2 Maintenance intervals 51
6.3 Maintenance list 52
6.4 Removing and installing components for maintenance 53
6.4.1 Preparing the Condair Omega Pro for the removal of components 53
6.4.2 Removal and installation of the scale collector tank 54
6.4.3 Removal and installation of the steam cylinder 56
6.4.4 Removal and installation of the drain cup 59
6.4.5 Removal and installation of the lling cup, the level unit and the water hoses 60
6.4.6 Removal and installation of the drain pump 61
6.4.7 Removal and installation of the inlet valve 62
6.4.8 Removal and installation of the steam cylinder receptacle 63
6.5 Notes on cleaning the unit components 64
6.6 Notes on cleaning agents 66
6.7 Resetting the maintenance counter 67
6.8 Performing software and rmware updates 68
7 Fault elimination 69
7.1 Important notes on fault elimination 69
7.2 Fault indication 69
7.3 Malfunction list 70
7.4 Saving fault and service histories to a USB memory stick 74
7.5 Resetting the fault indication 74
7.6 Replacing the fuses and backup battery in the control unit 75
8 Taking out of service/Disposal 76
8.1 Taking out of service 76
8.2 Disposal/Recycling 76
9 Productspecication 77
9.1 Performance data 77
9.2 Operating data 78
9.3 Connections/Dimensions/Weights 78
9.4 Certicates 78

5Introduction
1 Introduction
1.1 To the very beginning
We thank you for having purchased the Condair Omega Pro steam generator.
The Condair Omega Pro steam generator incorporates the latest technical ad van ces and meets all
recognized safety standards. Nevertheless, improper use of the Condair Omega Pro steam generator
may result in danger to the user or third parties and/or damage to property.
To ensure a safe, proper, and economical operation of the Condair Omega Pro steam generator, please
observe and comply with all information and safety instructions contained in the present documentation
as well as in the separate documentations of the components installed in the humidication system.
If you have questions after reading this documentation, please contact your Condair representative.
They will be glad to assist you.
1.2 Notes on the operation manual
Limitation
The subject of this operation manual is the Condair Omega Pro steam generator in its differ-
ent versions. The various options and accessories are only described insofar as this is necessary for
proper operation of the equipment. Further information on options and accessories can be obtained in
the respective instructions.
This operation manual is restricted to the commissioning, operation,maintenance and troubleshooting
of the Condair Omega Pro steam generator and is meant for welltrainedpersonnelbeingsufciently
qualiedfortheirrespectivework.
This operation manual is supplemented by various separate items of documentation (installation manual,
spare parts list, etc.), which are included in the delivery as well. Where necessary, appropriate cross-
references are made to these publications in the operation manual.

6Introduction
Symbols used in this manual
CAUTION!
The catchword "CAUTION" used in conjunction with the caution symbol in the circle designates notes
in this operation manual that, if neglected, may cause damage and/or malfunction of the unit or
damage to property.
WARNING!
The catchword "WARNING" used in conjunction with the general caution symbol designates safety
and danger notes in this operation manual that, if neglected, may cause injury to persons.
DANGER!
The catchword "DANGER" used in conjunction with the general caution symbol designates safety and
danger notes in this operation manual that, if neglected, may lead to severe injury or even death
of persons.
Safekeeping
Please safeguard this operation manual in a safe place, where it can be immediately accessed. If the
equipment changes hands, the documentation must be passed on to the new operator.
If the documentation gets misplaced, please contact your Condair representative.
Language versions
This operation manual is available in other languages. Please contact your Condair representative for
information.

7For your safety
2 For your safety
General
Every person working with the Condair Omega Pro must have read and understood the Condair Omega
Pro operation manual before carrying out any work.
Knowing and understanding the contents of the operation manual is a basic requirement for protecting
personnel against any kind of danger, to prevent faulty operation, and to operate the Condair Omega
Pro safely and correctly.
All icons, signs and markings applied to the components of the Condair Omega Pro must be observed
and kept in readable state.
Qualicationofpersonnel
All work described in this operation manual may only be carried out by specialists who are well
trainedandadequatelyqualiedandareauthorizedbythecustomer.
For safety and warranty reasons any action beyond the scope of this manual must be carried out only
by qualied personnel authorised by Condair.
It is assumed that all persons working with the Condair Omega Pro are familiar and comply with the
appropriate regulations on work safety and the prevention of accidents.
The Condair Omega Pro steam generator may not be used by persons (including children) with reduced
physical, sensory or mental abilities or persons with lacking experience and/or knowledge, unless they
are supervised by a person responsible for their safety or they received instructions on how to operate
the system.
Children must be supervised to make sure that they do not play with the Condair Omega Pro steam
generator.
Intended use
The Condair Omega Pro steam generator is intended exclusively for generation of steam for SPA
applicationswithinthespeciedoperatingconditions. Any other type of application, without the
written consent of Condair, is considered as not conforming with the intended purpose and may lead to
the Condair Omega Pro becoming dangerous and will void any warranty.
Operation of the equipment in the intended manner requires that all the information contained in this
operation manual are observed (in particular the safety instructions).

8For your safety
Danger that may arise from the Condair Omega Pro steam generator
DANGER!
Dangerofelectrichazard!
The Condair Omega Pro is mains powered. Live parts may be exposed when the unit is open.
Touching live parts may cause severe injury or danger to life.
Prevention: Before carrying out any work set the Condair Omega Pro out of operation as described
in chapter 4.5 (switch off the unit, disconnect it from the mains and stop the water supply) and secure
the unit against inadvertent power-up.
WARNING!
Hot water vapour - Danger of scalding!
The Condair Omega Pro produces hot water vapour. There is danger of scalding when coming
in contact with hot water vapour.
Prevention: Do not carry out any work on the steam system during operation (steam lines, steam
distributor, blower pack, etc.). If the steam system is leaky set the Condair Omega Pro immediately
out of operation as described in chapter 4.5. Correctly seal the steam system before putting the unit
into operation again.
WARNING!
Danger of burning!
During operation the components of the steam system (steam cylinder, steam distributor, etc.)
get very hot (up to 100 °C). There is danger of burning when touching the hot components.
Prevention: Before carrying out any work on the steam system set the Condair Omega Pro out of
operation as described in chapter 4.5, then wait until the components have cooled down sufciently
thus preventing danger of burning.
Preventing unsafe operation
If it is suspected that safe operation is no longer possible, the Condair Omega Pro should immediately
be shut down and secured against accidental power-up according to chapter 4.5. This can be the
case under the following circumstances:
– if the Condair Omega Pro is damaged
– if the electrical installations are damaged
– if the Condair Omega Pro is no longer operating correctly
– if connections and/or piping are not sealed
All persons working with the Condair Omega Pro must report any alterations to the unit that may affect
safety to the owner without delay.
Prohibitedmodicationstotheunit
Nomodicationsmustbeundertaken on the Condair Omega Pro without the express written consent
of Condair.
For the replacement of defective components use exclusively original accessories and spare parts
available from your Condair representative.

9Product Overview
3 Product Overview
3.1 Construction Condair Omega Pro steam generator
1 Scale collector tank drain valve
2 Scale collector tank
3 Coupling sleeve
4 Water supply connector (G 3/4")
5 Inlet valve
6 Drain pump
7 Water supply hose
8 Water lling and drain hose
9 Level hose
10 Level unit
11 Pressure equalizing pipe
12 Filling cup
13 Condensate connector (to cylinder)
14 Condensate connector (to drain)
15 Steam connector (ø45 mm)
16 Steam outlet hose
17 Heating cable plug
18 Heating elements
19 Excess temperature switch
20 Steam cylinder
21 Drain hose
22 Drain cup with drain connector (ø30 mm)
23 Unit switch
24 Control board with display and control unit
25 Cable feed throughs
26 Rating plate
27 Driver board
28 Ground terminals
29 Main contactor
30 Heating contactors
31 Power board
Fig. 1: Construction Condair Omega Pro steam generator (gure shows medium sized unit)
3
4
5
7
6
8
10
12
13
11
9
1
2
20
19
22
21
15
14
26
31
23
25
24
30
27
29
17
18
16
28

10 Product Overview
3.2 Functional description
The Condair Omega Pro is an atmospheric steam generator. It operates on the resistance heating
principle and is designed for direct room air humidication (with blower pack) and for steam generation
for SPA applications.
Water supply
The water (drinking water, reverse osmosis water or demineralized water) is supplied via a lter valve
(accessory "Z261") to the steam generator. It reaches the steam cylinder via the level controlled inlet
valve and the open lling cup.
Note: the open lling cup is designed in such a way, that the supply water is separated from the unit
water. That means, that no unit water can ow back into the supply water line.
Note: The steam generator Condair Omega Pro can also be supplied with reverse osmosis water from
the Condair RO-A pure water system (see system overviews in chapter 3.3 and chapter 3.4). Detailed
instructions on the Condair RO-A pure water system can be found in the separate manual for this product.
Level regulation
The water level in the steam cylinder is continuously monitored with the level unit. If the water level
reaches a preset level (due to the evaporation process) the level unit supplies a signal to the controller.
This opens the inlet valve and the steam cylinder is lled up. When the preset operating level is reached,
the level unit supplies another signal to the controller to close the inlet valve.
The pressure equalizing pipe between the steam connection and the level unit ensures that the water
levels are the same in the steam cylinder and the level unit.
Steam generation regulation
The steam is produced in the steam cylinder by several resistance heating elements. An external or the
integrated continuous controller control the steam production fully variably from 0 to 100 %.
Alternatively the Condair Omega Pro can be controlled also via an On/Off controller.
Flushing
The evaporation process increases the concentration of minerals in the water of the steam cylinder. A
suitable volume of water must be ushed out of the steam cylinder from time to time and replaced by
fresh water to ensure that this concentration does not exceed a specic value unsuitable for operation.
The Condair Omega Pro consists of the following two forms of ushing:
– Automaticushingtakes place as soon as the water in the steam cylinder exceeds the upper
operating level (e.g. by foaming of the water).
– Flushing dependent on time performs the ushing process at preselected time intervals.
Automatic or time-dependent ushing takes place depending on the water quality and the operating data.
If the lowest operating level is reached during the ushing process, the inlet valve remains open until
the water level in the steam cylinder has reached the normal working level again. If the lowest operating
level is not reached, the inlet valve is closed.
Scale collector tank
The minerals precipitated by the evaporation process sink down in the steam cylinder and accumulate
in the scale collector tank, thus extending the service intervals and reducing the maintenance work.
Units designed for operation with water from a RO system or with de-ionized water do not require a scale
collector tank as RO water and de-ionized water contains only small amounts of minerals.

11Product Overview
3.3 SystemoverviewSPAcabinhumidication
1Steam generator
2Steam outlet connector
3Water drain connector
4 Water supply connector
5Water supply line
6 Manometer (recommended)
7Filter valve (accessory Z261)
8Open funnel with water trap
9Drain hose (supplied)
10 Electrical isolator control voltage supply
11 Electrical isolator heating voltage supply
12 Steam line (accessory DS80)
13 Steam distributor (by others)
14 Electrical isolator voltage supply Condair Delta
SPA Control Box
15 Condair Delta SPA Control Box
16 SPA Display
17 Pure water system Condair RO-A (option)
Fig. 2: System overview SPA cabin humidication
DS80
Z261
12
13
14
15
16
9
8
11
10
1
2
3
4
5
6
7
17
SPA cabin
* by others
*
*
*
*
*
*
*

12 Product Overview
3.4 Systemoverviewdirectroomhumidication
1Steam generator
2Steam outlet connector
3Water drain connector
4 Water supply connector
5Water supply line
6 Manometer (recommended)
7Filter valve (accessory Z261)
8Open funnel with water trap
9Drain hose (supplied)
10 Electrical isolator control voltage supply
11 Electrical isolator heating voltage supply
12 Steam line (accessory DS80)
13 Condensate line (accessory KS10)
14 Blower Pack (accessory BP)
15 Humidity controller or humidity sensor
16 High limit humidistat
17 Pure water system Condair RO-A (option)
Fig. 3: System overview direct room humidication
2
3
4
7
5
6
BP
BP
11
10
1
15
16
12
14
14
13
KS10
DS80
9
8
Z261
17
* by others
*
*
*
*
*
*
*
*

13Operation
4 Operation
The Condair Omega Pro steam generator may be commissioned and operated only by persons familiar
with the Condair Omega Pro steam generator and adequately qualied. It is the owner’s responsibility
to verify proper qualication of the personnel.
4.1 First-time commissioning
The rst-time commissioning must always be done by a service technician of your Condair representative
or a well trained and authorised person of the customer. Therefore the current manual does not provide
detailed information on this procedure.
The following steps are carried out upon rst-time commissioning in the specied order:
• Inspecting the steam generator for correct installation.
• Inspecting the electrical installation
• Inspecting the water installation
• Inspecting the steam installation
• Flushing the water supply line.
• Conguring the control or the Condair Omega Pro, respectively.
• Carrying out test runs including checking of the control and monitoring devices.
• Filling in the commissioning protocol.
4.2 Display and operating elements
Fig. 4: Display and operating elements
DANGER!
Risk of electric shock!
After switching off the unit switch, there is still live voltage inside the control compartment of the Condair
Omega Pro. Therefore, before opening the unit the steam generator must be always separated
from the mains supplies (heating and control voltage) via the electrical isolators.
1 External electrical isolators for heating and control volt-
age supply (not includ ed in the delivery, must be install-
ed in the mains supply lines)
2 Touchscreen
3 Status LED
– green: Condair Omega Pro is producing steam
– green pulsing: Condair Omega Pro is in standby
operation
– orange: Warning present or maintenance due
– red: Fault present
4 Unit switch

14 Operation
4.3 Commissioning after an interruption of operation
The following description outlines the start up procedure after an interruption of operation (e.g. after ser-
vicing the steam generator). It is assumed that rst-time commissioning has been carried out properly by
the service technician of your Condair representative and the Condair has been congured accordingly.
1. When putting the steam generator into operation the rst time or when putting the steam generator
into operation after work has been carried out on the steam system, the operating personnel must
check whether the steam pipe is open over the entire length. To do this proceed as follows:
Remove the front door on the steam cylinder side of the Condair Omega Pro.
• Undo the upper hose clamp of the steam hose in the unit with a screwdriver and pull the hose
down to remove it from the steam connection.
• Start up the ventilation system and check whether the pressure on the open steam connector
corresponds to the pressure in the ventilation system.
DANGER!
A steam line that is reduced in cross section or completely closed will cause an excessive
increase in pressure in the steam cylinder when the unit is operating and could lead to the
risk of scalding accidents!
Therefore: If no draught or only a slight one can be detected the steam line must be checked for
blockages and reductions in cross section before continuing with commissioning and you must
ensure that the steam line is open across the entire length and through the whole cross section.
2. Examine the steam generator and installation for possible damage.
DANGER!
A damaged unit or systems with damaged installations may present danger to human life
or cause severe damage to material assets.
Therefore: Damaged systems and/or systems with damaged or faulty installations must not be
operated.
3. Mount front doors of the unit and lock it (if applicable).
4. Open the lter valve / shut-off valve in the water supply line.
5. Switch on the electrical isolators in the mains supplies (heating and control voltage).
6. Switch on the unit switch of the steam generator.
The steam generator carries out an automatic system test (initialising). If a fault is detected during
the system test, a corresponding fault message is shown in the maintenance and malfunction indi-
cation eld (see chapter 5.1.2).
Iftheinitializationissuccessful, the steam cylinder lls up and a function check on the level unit
is carried out. If a fault is detected during the function check on the level unit, a corresponding fault
message is shown in the maintenance and malfunction indication eld (see chapter 5.1.2).
If the function check on the level unit is successful, the Condair Omega Pro will be in normal op-
erating mode and the standard operating display is shown. The heating current switches on as
soon as the controller/sensor demands for steam. The LED lights green and steam is produced
after a short delay.

15Operation
4.4 Notes on operation
4.4.1 Inspections during operation
During operation the Condair Omega Pro and the humidication system have to be inspected weekly.
On this occasion check the following:
• the water and steam installation for any leakage.
• the steam generator and the other system components for correct xing and any damage.
• the electric installation for any damage.
If the inspection reveals any irregularities (e.g. leakages, error indication) or any damaged components
take the Condair Omega Pro out of operation as described in chapter 4.5. Then, contact your Condair
representative.
4.4.2 Remote operating and fault indication
Via the relays on the optional operating and fault indication board the following operating status are
indicated:
Activated
remote indication relay
When?
"Error" An error is present, operation is stopped.
"Service" The control software has detected that the small or the large main-
tenance is due. The steam generator must be serviced according to
the maintenance section in this manual (see chapter 6).
"Steam" Demand present/steam generation
"Unit on" The steam generator system is switched on and under voltage

16 Operation
4.4.3 Draining of the steam cylinder
To perform a draining of the steam cylinder proceed as follows:
1. Press on the <Drain> button in the standard operating display. The "Manual" submenu appears.
2. In the "Manual" submenu press on the button of the cylinder(s) to be drained (<Cylinder A>, <Cyl-
inder B> or <Cylinder A/B>).
Note: on single units <Cylinder A> button is shown only.
3. Press on the <Yes> button to start the draining of the steam cylinder(s). A possible running steam
generation process is interrupted, then the drain pump starts and empties the steam cylinder. The
progress bar in the display shows the current status of the drain cycle. After draining has nished
the unit returns to the "Manual" submenu.
Note: in order to stop the drain cycle press the <Cancel> button in the draining progress window.
The drain cycle is stopped and the unit returns to the "Manual" submenu.
4. If you have to carry out work on the Condair Omega Pro, switch off steam generator via the unit
switch. Otherwise the steam cylinder is immediately lled again.
4.4.4 Flushing the Condair RO-A water supply system
Note: the RO ushing function in the "manual" submenu appears only, if the Condair Omega Pro is con-
nected to a Condair RO-A reverse osmosis system and if the reverse osmosis system was activated in
the factory menu.
To ush the RO water supply system proceed as follows:
1. Press on the <Drain> button in the standard operating display. The "Manual" submenu appears.
2. Press on the <Flush> button in the "Manual" submenu.
3. Press on the <Yes> button to start the ushing of the water supply system. The progress bar in the
display shows the current status of the ush cycle. After ushing has nished the unit returns to
normal operating mode.
Note: in order to stop the ush cycle press the <Cancel> button in the draining progress window.
The ush cycle is stopped and the unit returns to normal operating mode.

17Operation
4.4.5 PerformingacompleteushingoftheCondairRO-Asystem
Note: the FWA ushing function in the "manual" submenu appears only, if the Condair Omega Pro is
connected to a Condair RO-A reverse osmosis system and if the reverse osmosis system was activated
in the factory menu.
To perform a complete ushing of the RO system proceed as follows:
1. Press on the <Drain> button in the standard operating display. The "Manual" submenu appears.
2. Press on the <FWA> button in the "Manual" submenu.
3. Press on the <Yes> button to start the ushing of the complete system. The progress bar in the
display shows the current status of the ush cycle. After ushing has nished the unit returns to the
"Manual" submenu.
Note: in order to stop the ush cycle press the <Cancel> button in the draining progress window.
The ush cycle is stopped and the unit returns to normal operating mode.
4.5 Taking the unit out of operation
In order to take the Condair Omega Pro steam generator out of operation (e.g. for maintenance purpose),
perform the following steps:
1. Close the shut-off valve in the water supply line.
2. If you have to carry out maintenance work on the steam cylinder and/or on the scale collector tank
perform a cylinder draining (see chapter 4.4.3).
Note: On units equipped with the optional drain valve for the scale collector tank, the scale collector
tank is drained simultaneously when performing a draining of the steam cylinder.
3. Switch off unit switch of the steam generator.
4. Disconnect steam generator from the mains: Switch off both electrical isolators in the mains
supply lines (heating and control voltage) and secure switches in "Off" position against accidentally
being switched on, or clearly mark the switches.
5. If you have to carry out maintenance work on the steam cylinder, empty the scale collector tank via
the drain valve.
WARNING!
Danger of burning!
The temperature of the water in the scale collector tank can be up to 95 °C.
Therefore: wear isolating gloves and open the drain valve carefully.
If no water ows out from the open drain valve, the drain inside the scale collector tank is clogged and
the scale collector tank may not be emptied. If this is the case, wait until the temperature indication
adhesive on the scale collector tank indicates a temperature below "<50°C" before dismantling the
tank (since the scale collector tank is lled with water).

18 Operating the control software
5 Operating the control software
5.1 Standard operating display
After switching on the Condair Omega Pro and the automatic system test the steam generator is in
normal operating mode and the standard operating display is shown.
Note: the appearance of the standard operating display depends on the current operating status and the
conguration of the control of the system and can deviate from the display shown below.
The standard operating display is structured as follows:
Fig. 5: Standard operating display
Cylinder selection (shown only on units with 2 steam cylinders)
Maintenance/malfunctions indication eld
(see chapter 5.1.2)
Steam control information
Operating status eld
(see chapter 5.1.1)
Access Help screen
Cylinder Draining (and optional RO-A ushing functions)
Access system informations
Access main menu

19Operating the control software
5.1.1 Operating status indication
The following operation status indications may appear during operation:
Operating status indications Description
The control is initialising.
The Condair Omega Pro is in standby mode (no demand present).
The Condair Omega Pro performs a cylinder ushing.
The Condair Omega Pro is producing steam.
The Condair Omega Pro checks the function of the level unit.
The Condair Omega Pro is connected to a BMS, and the BMS has activated the diagnostic mode.
The Condair Omega Pro has been stopped via an external enable contact (remote enable/disable).
The Condair Omega Pro is in standby mode and the keep warm function is activated.
The Condair Omega Pro is stopped due to a malfunction which prevents further operation.
Additionally "Warning" or "Fault" is displayed in the maintenance and malfunction eld.
5.1.2 Maintenance and malfunction indications
The following maintenance and malfunction indications may appear during operation:
Maintenance and
malfunction indications
Description
No malfunction present. By pressing on the indication eld the service menu can be accessed.
This message appears if the maintenance counter for the large maintenance has elapsed. If the
large maintenance is not carried out, and the maintenance counter is not reset within 7 days,
a corresponding fault message appears.
Carry out the large maintenance, then reset the maintenance counter in the "Service" submenu.
This message appears if the maintenance counter for the small maintenance has elapsed. If the
small maintenance is not carried out, and the maintenance counter is not reset within 7 days,
a corresponding fault message appears.
Carry out the small maintenance, then reset the maintenance counter in the "Service" submenu.
A malfunction with status "Warning" is active. Additionally the status LED lights yellow. Depend-
ing on the malfunction the Condair Omega Pro is either be stopped or stays operable for a
certain period of time.
The Condair Omega Pro was stopped due to a malfunction, which prevents further operation.
Additionally the status LED lights red.

20 Operating the control software
5.2 Navigating/Operating the control software
Navigation element Action
Accessing main menu
Accessing system informations
Performing manual steam cylinder draining
Accessing help screen
If you press on a eld with a blue arrow symbol a new screen with additional
informations or settings appears.
This symbol on the left side of the operating status eld and of the mainte-
nance/malfunctions indication eld indicates, that the system is working ok.
This symbol on the left side of the maintenance/malfunctions indication
eld indicates, that a Warning is present. Press on the eld to get further
information.
This symbol on the left side of the operating status eld and of the main-
tenance/malfunctions indication eld indicates, that a Fault is present (ad-
ditionally the LED lights red). Press on the eld to get further information.
Jumps back to previous screen (Cancel and back)
Scroll up/down in the present window
Increase/decrease value
Delete shown value
Conrm set value or selected option