Conde 10.1" V2 Room Screen Guide

Condeco 10.1” V2 Room Screen (T201502)
Mounting Information

Page 2 of 9
Condeco 10.1’’ Room Screen Mounting Instructions
Contents
General instructions...................................................................................................................................3
Mounting on Glass......................................................................................................................................7
Screen Commission Pre-requisites.........................................................................................................8
Contact .........................................................................................................................................................9

Page 3 of 9
Condeco 10.1’’ Room Screen Mounting Instructions
General instructions
The Condeco screen can be mounted to solid or partition walls using the mounting plate
supplied and suitable fixings.
When deciding where to mount the Condeco room screen please consider the locations of
the cable entry points on the back plate.

Page 4 of 9
Condeco 10.1’’ Room Screen Mounting Instructions
The final screen height should be determined by local disability access requirements. The
ADA (Americans with Disabilities Act) Guidelines requires that the highest point of interaction
is not greater than 48 inches or 1220 mm. We find 1150mm –1170mm from the bottom of
the device typically a suitable height.
Once desired screen height is finalised, the back needs to be fixed to the wall using the
screws supplied or using double sided tape (for mounting on Glass) to secure the back plate
in position.
Fixing Point
Fixing Point

Page 5 of 9
Condeco 10.1’’ Room Screen Mounting Instructions
Once the back plate has been fixed to the wall connect the LAN cable to the rear of the
Condeco screen.
Feed the LAN cable in the cable guide recess that is present on the back plate and the device
and also based on where the LAN cable needs to be routed to.
Network
Port
Network Cable
Input (Both
Sides)
Network
Cable Input
Network
Cable
Input

Page 6 of 9
Condeco 10.1’’ Room Screen Mounting Instructions
Clip the screen on to the back plate and screw the unit in place using the screws provided.
Fixing screws to fix the
unit to the back plate.

Page 7 of 9
Condeco 10.1’’ Room Screen Mounting Instructions
Mounting on Glass
The following illustration shows a Condeco screen mounted to Glass. When mounting on
glass we recommend that the use of the following materials.
To fix the screen to the Glass wall, you will need to use the pre cut strips between the back
plate and the Vinyl. We recommend using 2 of the strips per screen, placed on to the Vinyl.
The back plate attaches to the Strips, and the strips are attached to the Vinyl.
Firstly, the vinyl is attached to the glass (Please review the 3M Application Instruction
document for wet application procedure. Ensure the vinyl is allowed to dry for at least 24
hours before continuing). The strips are then attached to either the Vinyl or the back plate
and finally the back plate is pushed onto the vinyl.
Part Numbers:
CO-T201502-GMK for the 10.1” V2 Condeco screens.
Kit Contents:
1 x pre-cut silver/aluminium colour vinyl with shaped corners –183mm x 247mm
1 x pre-cut silver/aluminium colour vinyl with shaped corners –120mm x 214mm
3 x pre-cut strips of 3M 4941 VHB tape 110mm x 25 mm.
Screen
Back Plate
Vinyl
VHB Tape

Page 8 of 9
Condeco 10.1’’ Room Screen Mounting Instructions
Screen Commission Pre-requisites
If screen commissioning has been purchased as part of the installation, you will need to
ensure the following pre-requisites are in place prior to an engineer attending site:
Screen back plates fitted in position to the location requirements.
Pre terminated network cable with RJ45 connector at the screen. The terminating cable
should be approximately 20cm from the back plate entry to the connector.
The provided network cable should be patched and tested as operational on the
network.
The network connection provided must be capable of supplying POE to the screen either
from the switch or by the use of an inline injector somewhere between the screen and
the network switch. These should be in place and powered. We recommend using a
Netgear POE switch.
The network point should be tested to ensure routing of http traffic port 80 is available to
the server that the Condeco software is to be installed on.
If the use of static IP addresses is required these should be pre-allocated and the
engineer advised of the IP addresses and the meeting room/screens they are to be used
on.
On attendance, the engineer will mount each screen to the pre installed back plates,
program any static IP addresses required, commission the screens to the software and test
the functionality.

Page 9 of 9
Condeco 10.1’’ Room Screen Mounting Instructions
Contact
Europe (Head Office)
8th Floor Exchange Tower
2 Harbour Exchange Square
London E14 9GE
Tel [phone]
[e-mail]