Condor T-ramp Instruction manual

CONDOR®

T-RAMP

QUICK START MANUAL

STOP! WARNING: READ THIS FIRST!

It is recommended that detaching the T-Ramp from its shipping skid be performed by at least two (2) able-bodied adults.

First Read and Understand the Instruction manual and product labels for important safety, set-up and troubleshooting information. If you have problems setting up or

using the Condor® T-Ramp

, contact customer service @ 1-815-754-7418 or contact us via e-mail @ www.condor-lift.com. Condor® T-Ramp

is not intended for

use by children.

Skid Detachment Instructions

Remove all parts from shipping box. Check the parts below to make sure you have all the parts needed to remove and operate your Condor® T-Ramp

before

beginning. In the unlikely event that you find a part damaged or missing, please call customer service @ #815-754-7418

-7-Way T-Ramp power cord

-Wireless Remote

-Fuse / Hardware bag

-Operation Manual – Refer to Manual for details

-3/4” wrench or socket (Not Included)

-9/16” wrench or socket (Not Included)

-Metal band cutters (Not Included)

-Vehicle with Class III or better hitch receiver assembly (Not Included)

1. Place skid behind truck with wheels closest to truck.

Remove and open included shipping box.

2. Remove axle / wheel assemblies by cutting steel bands.

3. (a) Install axle / wheel assemblies in storage position

(See Section 4.4), (b) Remove Kickstand from shipping

skid.

4. Attach and Secure Kickstand (See Section 4.3 – 4.5)

5. Release one (1) tie down strap (a). Using a 9/16” wrench,

remove the Mechanism Hold-Down Bracket (b). While holding

the second tie down strap, release second tie down strap (c).

Continue holding the tie down strap to be sure entire unit

remains in the balanced, upright position.

6. With (2) people, lean T-ramp back until the axle / wheel

assemblies touch the ground (a). Using a ¾” wrench or socket,

remove the (2) bolts securing the Mechanism to the skid (b). The

T-ramp is now free from the shipping skid.

7. Lean T-Ramp back slowly until the Kickstand Wheel is

touching the ground. The T-Ramp should now be safely

supported to roll it into position to connect to truck hitch. Use

wireless remote or onboard switch to lower the Mechanism to

line up with truck hitch. Follow the instructions in Section 5.2 to

secure the T-Ramp to your truck for transport.

8. The T-Ramp height setting arrives from the factory set at

Setting 1, with the Stop Ring un-set. See above diagram and

Section 5.3.2 in the Operation Manual to properly set the Stop

Ring before use. Also See Section 5.3.2 to customize the T-Ramp

height setting for various vehicles.

CAUTION:

Refer to the included Operations Manual prior to operating this product. Always make sure that all fasteners are tight and all pins are in place prior to use. Understand

the limitations of this product and do not exceed these limitations. Technical Components Development & Design is not responsible for any damage incurred by

exceeding this product’s limitations in structure and/or functionality. All illustrations and specifications contained in this guide and the Operations Manual are based on

the latest product information available at the time of printing. Technical Components Development & Design, Inc. reserves the right to make changes at any time,

without notice, in color, materials, equipment, options, specifications and models. Models may be shown with optional equipment. If instructions are not clear, please

refer to the Operations Manual included with the T-Ramp

TM.

. Additional information is available at www.condor-lift.com or call 1-800-461-1344.

Return Policy:

The Condor® T-Ramp

is non-returnable. (See warranty information for more details)

Notice:

Inspect your product upon delivery. Any consideration for return does NOT include any damages which may have occurred during shipment of the product. In fact, the

moment the product leaves the premises of the manufacturer it immediately becomes the sole property of the purchaser. It is most important that upon delivery, the

recipient thoroughly inspect the product to satisfy that it is being received in perfect condition, and without damage. If damage is found, it will be the complete

responsibility of the recipient to identify (and to make known), this damage prior to signing the acceptance page for the delivering freight company. The manufacturer

accepts NO responsibility for damaged freight. Claims must be dealt directly by the recipient, and with the freight carrier who is delivering the product.

Thank you for purchasing the Condor® T-Ramp

Condor®

is a registered trademark of

Technical Components Development & Design, Inc.

The Condor® T-Ramp

is US Patented & International Patent Pending.

Patent Numbers: 8,123,455; 9,010,795; 13/406,425; 61/984,362

Technical Components Development & Design, Inc.

Condor® Products

210 W. Stephenie Drive

Cortland, IL 60112

Phone: (815) 754-7418