Congatec conga-QKIT/IoT User manual

Copyright © 2015 congatec AG QKIT_IoTq12 1/5
conga-QKIT/IoT
Starter Kit for Qseven IoT Gateway Development
Hardware Quick Start Guide

Copyright © 2015 congatec AG QKIT_IoTq12 2/5
Preface
This guide gives a brief overview of the conga-QKIT/IoT and how to quickly
install, configure and operate it.
For more information about the conga-QKIT/IoT, refer to the conga-QKIT/
IoT datasheet and the User’s Guide on the congatec website.
ESD Precaution
All congatec AG products are electrostatic sensitive devices and are
packaged accordingly. Do not open or handle a congatec AG product
except at an electrostatic-free workstation.
Additionally, do not ship or store congatec AG products near strong
electrostatic, electromagnetic, magnetic, or radioactive fields unless the
device is contained within its original manufacturer’s packaging. Be aware
that failure to comply with these guidelines will void the congatec AG
Limited Warranty.
Product Overview
The conga-QKIT/IoT - a congatec Qseven IoT Development Kit consists of:
•congatec’s conga-QA3/E3827 module with suitable heatspreader
•Full featured Qseven IoT carrier board,
•7” TFT touch display,
•Mini PCIe WLAN card and WLAN antenna with cable
•USB touch controller
•5V Power supply
•USB stick pre-installed with demo Operating System Image.
•Set of cables for adequate setup.
The conga-QA3/E3827 module features the Intel Atom E3827 dual core
processor with 1.75 GHz frequency, high definition graphics, 2GB dual
channel DDR3L-1333 memory and onboard 4GB eMMC.
With maximum 8W TDP processor, the conga-QKIT/IoT offers an Ultra Low
Power board with high computing performance and outstanding graphics.
Kit Contents
Contents Description
PN. No Name Description Qty
077600 conga-QKIT/IoT IoT Kit based on Intel Atom E3827 processor.
Supports Windriver IDP and build OS.
077601 conga-eNUC/Qseven IoT Evaluation board for QSeven IoT modules 1
015101 conga-QA3/E3827 Qseven module with Intel Atom processor, 2GB
dual channel memory and 4GB eMMC flash.
1
015192 conga-QA3/CSP-T Standard conga-QA3 passive cooling 1
10000148 WLAN mini-PCIe card Intel®7260.HMWG (WiFi, Bluetooth). 1
10000149 WLAN Antenna 802.11ac/a/b/g/n 2 dBi Omnidirectional Joint. 2
10000151 QKIT/IoT Power Supply 30W, 5V@6A Power supply. (C13 power cord not
included)
1
10000153 Touch Controller TSC-34/RU-F Touch controller board for the 7” TFT Display 1
14000012 WLAN pigtail cable 20cm RP-SMA WLAN pigtail cable. 2
14000139 cab-eSATAp to 22pin 2.5”
SATA
Cable with powered eSATA connector on one
end and SATA connector on the other end
1
14000140 cab-QKIT/IoT DC-IN 160mm DC-IN adapter cable for QKIT/IoT. 1
14000143 cab-QKIT/IoT LVDS conga-QKIT/IoT LVDS cable. Used for
ATM0700L6E display (7” TFT display)
1
14000158 cab-QKIT/IoT TSC-34/RU conga-QKIT/IoT USB touch controller cable. 1
14000159 QKIT/IoT Cable Set (Optional) Cable set. Contains USB and audio cables. N.A
10000147 LCD Panel 7” TFT 800x480 display with resistive touch. 1
10000113 congatec USB Stick 8 GB USB stick with pre-installed IoT OS image. 1
65000014 Intel SK50 Trial Licence 90 day trial licence for Wind River IDP 1
Quick Start Guide conga-QKIT/IoT Quick Start Guide
Power supply
USB touch controller
conga-eNUC/Qseven IoT
carrier board
conga-QA3/HSP-B
conga-QA3/E3827
7” TFT touch display
WLAN antenna with cable
congatec USB stick with
OS image
Intel mini-PCIe (WLAN)
Optional cable set (USB,
audio)

Copyright © 2015 congatec AG QKIT_IoTq12 3/5
Hardware Setup
Steps:
•Install the congatec passive cooling solution or an appropriate
conga-QA3 cooling solution.
•Attach the conga-QA3 Qseven module with congatec passive cooler
to the conga-eNUC/Qseven IoT evaluation board.
•Connect the twin connector end of the LVDS cable to the evaluation
board (LVDS & backlight) and the single connector end to the display
panel.
•Connect one end of the touch controller cable to the USB header on
the evaluation board (bottom side) and the other end to the display
panel.
•Connect other required peripherals.
•Plug in one end of the DC_IN adapter cable to the 5V power supply.
To power on the system, plug in the other end of the DC_IN adapter
cable to the evaluation board.
conga-QKIT/IoT Interfaces and Functionality Overview
Top Side
Bottom Side
5V Power Supply
PN: 10000151
DC_IN Adapter Cable
PN: 500016
WLAN Pigtail Cable
PN: 14000012
Touch Controller Cable
PN: 14000158
Touch Controller
PN: 10000153
conga-eNUC/Qseven IoT
(PN: 077601)
+
Qseven Module
(PN: 615102)
+
Passive Cooling Solution
(PN: 015192)
LVDS Cable
PN: 14000143
Display Cable
PN: 10000147
DisplayPort USB 3.0 eSATA Gbit Ethernet
LVDS EDID
EEPROM
TPM 1.2/2.0
Qseven Module Connector
Internal Display (LVDS, Backlight ....)
SIM Slot
PWR 1)
(NC) GND +5V
RESET, FAN
Encrypted
EEPROM
2x Internal USB Speaker Audio
MIC/HP
mSATA module
Sentinel HL
HSPA/LTE
or
I/O module 3)
Wifi + BT
module 3)
CR 2032
Battery

Copyright © 2015 congatec AG QKIT_IoTq12 4/5
Qseven Module Connector
6
Power-IN
SIM Card Slot
5
Backlight Voltage (only for >5V rails)
3
LVDS
4
Backlight
Fan
2
3 2 1
1
1
1 1 2 330 20
1
Power-IN 5V Single Supply
MC1.5/3-G-3.5 Phoenix
•Reverse voltage protection is
implemented.
•Fuse and line filter have to be
implemented externally.
Use Phoenix FMC1.5/3-ST-3.5
to connect power cord.
Connection method:
Spring-cage connection.
Fan (temp. controlled)
53398-0471 Molex
Pin 3 has internal 10k PU to VCC3V3.
Only one fan connector (top or
bottom) at a time can be used.
1 VCC5V
2 DGND
3 Not connected 1 DGND
2 VCC5V
3 TACHO_IN (10 PU)
4 PWM_OUT (5V)
Note
LVDS (out)
DF19G-30P-1H Hirose (max.
1A/pin with AWG28)
Backlight (for non 5V)
Only used if Backlight_VCC can
not be driven from internal VCC5V
(max. input 12V/5A).
Backlight (out)
DF19G-20P-1H Hirose (max.
1A/pin with AWG28)
SIM Card Slot
Signals are connected to mini
PCIe full size socket (contacts
on top side).
1 LVDS_A0- 16 LVDS_B1+
2 LVDS_A0+ 17 DGND
3 LVDS_A1- 18 LVDS_B2-
4 LVDS_A1+ 19 LVDS_B2+
5 LVDS_A2- 20 LVDS_BCLK-
6 LVDS_A2+ 21 LVDS_BCLK+
7 DGND 22 LVDS_B3-
8 LVDS_ACLK- 23 LVDS_B3+
9 LVDS_ACLK+ 24 DGND
10 LVDS_A3- 25 VCC5 (5V)
11 LVDS_A3+ 26 VCC5 (5V)
12 LVDS_B0- 27 VCC5 (5V)
13 LVDS_B0+ 28 VCC5 (3.3V)
14 DGND 29 VCC5 (3.3V)
15 LVDS_B1- 30 VCC5 (3.3V)
1 Ext. Backlight_VCC IN (max 12V)
2 DGND
3 Ext. Backlight_VCC switched
Note
5
1 Always on
2 Ext. Backlight_VCC
3 Switched
4 Ext. Backlight_VCC
5
6 DGND
7
8
9 Always on
10 Int. Backlight_VCC5V
11
12 Switched
13 Int. Backlight_VCC5V
14 BL_Enable (ONN/OFF#) (3.3V)
15 BL DIMM Control (PWM) (3.3.V)
16 DGND
17
18 Do not connect
19 Reserved (Programming Interface)
20
34
6
12
Internal Interfaces (Top Side)

Copyright © 2015 congatec AG QKIT_IoTq12 5/5
Audio (MIC, Headphone)
53261-1071 Molex
2x Internal USB
2x 53398-0571 Molex
USB 5 is not available if Sentinel HL
Security Controller is assembled.
Speaker (Left/Right)
2x 53261-0471 Molex
4 or 8 Ohms and 2W max. output
Power.
USB1
USB5
The conga-QKIT/IoT software
documentation can be found
here:
www.congatec.com/conga-qkitiot
You can also find the conga-
QA3 documentation here:
www.congatec.com/conga-qa3
The conga-QA3 drivers can be
found in the restricted area of the
congatec website.
To gain access to the drivers, you
must register. Contact your local
congatec sales representative if you
require assistance.
Note
Documentation and Drivers
FAN (Temp. Controlled)
53398-0371 Molex
Pin 3 has internal 10k Pull-Up to
VCC3V3.
Reset
53398-0371 Molex
1 DGND
2 VCC_FAN (5V, PWM)
3 TACHO_IN (10K PU)
Note
12
3
5
4
Internal Interfaces (Bottom Side)
mSATA module
HSPA/LTE
or
I/O module
Wifi + BT
module
CR 2032
Battery
1
2x Internal USB
2
Speaker (R/L)
3
Audio (MIC, Headphone)
4
Reset
FAN
5
Note
1 VUSB (5V, max. 1A)
2 USB_N
3 USB_P
4 DGND
5 DGND
1 RST#
2 DGND
1 OUT+
2
3 OUT-
4
Note
1 AGND
2 HP_OUT Left
3 HP_OUT Right
4 AGND
5 SENSE_HP_OUT# (HP active when
pin 5 is connected to AGND)
6 SENSE_MIC# (MIC active when pin
6 is connected to AGND)
7 AGND
8 MIC_Left (MIC_MONO)
9 MIC_Right
10 AGND