Conlan Prox P1000 User manual

Prox reader
P1000
Art. No: 480070 (black), 480071 (white)
User manual
P1000_usermanual_ENGaug20

2
Table of Contents
1. Introduction
2. Installation
3. Programming users
3.1 Mastertransponder
3.2 Programming user tags
3.3 Deleting user tags
4. Conguration
4.1 Programming mode
4.2 Settings
4.2.1 OC Split
4.2.2 OC Inverted
4.2.3 Timeout
4.2.4 Free locker
page 3
page 3
page 4
page 4
page 4
page 4
page 5
page 5
page 5
page 5
page 5
page 6
page 6

3
1. Introduction
P1000isaexibleProxreaderformanyapplications,readingbothAtmeland
E-marine.Thereaderhas3LED’s(yellow,greenandred)forindicationofapproved/
rejectedtagandfornavigationwhenconguratingthereaderssettings.Upto80
users positions (possible in 2 blocks for individual output).
InstandbytheyellowLEDislit( )
ByapprovedtagtheyellowandgreenLEDarelit( )
ByrejectedtagtheredLEDislit( )
2. Installation
Mount the reader on a even surface.
Connectthewirestopowersupply,lockingdevice,assemblyboxetc.
Note: Right after the voltage is applied lights all 3 LED’s and the buzzer sounds.
RightaftertheyellowLEDashesandthebuzzerissilent.

3. Programming user tags
3.1 Master transponder
BeforeyoucanusetheP1000youhavetoprogramaMastertransponder
(indication = **).ShowthattagyouwantasMastertransponder,agreenlight
conrmstheprogrammingandtheP1000isnowreadyforprogrammingusertags
andconguratingthesettings.
3.2 Programming new user tags
TheP1000has2outputs(yellowandwhitewire)thatcanactivateeachlockingdevice.
Bydefaultactivatesalltagsoutput2.Tosplittheoutputssee“OCSplit”.
** →  ** → 
To exit the programming, wait for 30 seconds or disconnect and reconnect the
voltage.
3.3 Deleting user tags
Deleting individual users
** →  ** → 
The P1000 can also delete all users at once, delete a lost user and delete the master
transponder.Usetheenclosedcongurationschemeasaguide.
4
Show the Master tag
1 time Show a Prox tag Show a Prox tag etc.
Show the Master tag
2 times Show a Prox tag Show a Prox tag etc.

4.Conguration
4.1 Programming mode
ToconguretheP1000,thereadermustbedisconnectedandreconnected(forabout
2seconds).NowtheMastertranspondercanconguretheP1000’ssettings.Please
seethecongurationschemas// markings.
RemembertoshowtheMasterTransponderwithin10secondstoallowyoutochange
theP1000’sconguration(timeout).
Thefollowingcongurationsonlyworkafterpowero/onasdescribed.
4.2 Settings
These settings can split the outputs, invert the outputs, and set the timeout.
Usetheenclosedcongurationscheme.
4.2.1 OC Split(1ashontheyellowLED)
Fromthefactory,theloadedtagsenablebothoutputs(userspace1to80).This
settingdividestheuserlocations.User1to40activatesoutput2(yellowwire)and
user space 41 to 80 activates output 1 (white wire).
Show master transponder for toggle ( = split, = combined).
4.2.2 OC1 and OC2 inverted(2or3ashesontheyellowLED)
ThesefunctionsinverttheP1000’soutputs(2ashesforoutput1and3ashesfor
output 2).
(= inverted, = not inverted).
5

6
4.2.3 Timeout (4ashesontheyellowLED)
This function sets the P1000’s timeout time. Show the master transponder to start,
thebuzzergivesabeepforeverysecond,showthemastertransponderagaintoend
the count.
4.2.4 Free locker (5ashesontheyellowLED)
TheFreelockerfunctioncanbeusedforaccesscontrol,especiallywheretheuser
often switches.
Showthereaderatag,andifthecabinetisfree,itwilllockandcanonlybeunlocked
with the same tag.
Free locker timeout
Countsforhours,soifyouwantittobesetto4hours,waitfor4seconds.
Save0forthereadernottoopenafterxhours,butonlywhenthetagis
showed to the reader again. Default is set to 10 hours.
User position 1 resets free locker.

7

ThankyouforchoosingConlan’sproducts.
For further assistance, please contact
Our support service.