Connect CSH-10TRI-255 User manual

AmbiColour Smart Triangle Lights
CSH-10TRI-255
User Manual

WHAT’S IN THE BOX
• Smart triangle lights x 10
• Controller
• Connection cables x 9
• Double-sided adhesive sticker x 10
• AC adaptor
• User manual
What you will need:
• Smartphone or tablet with Bluetooth
and connected to 2.4GHz band Wi-Fi
network
• Password for the Wi-Fi network

OVERVIEW
Large
connector
Small
connector
IN
OUTOUT

OVERVIEW
continued...
To enter pairing mode, press and
hold the On/O button for 4
seconds. The lights will ash once.
Wait for 2 seconds and lights will
start ashing.
Click the “On/O’ button: Control
the on/o of the light
Click the “M” button: Control the
static mode and dynamic mode of
the light.
Double-click the “M” button:
Enter the music rhythm mode.
• Clicking the button in music
rhythm mode will switch to
dierent rhythm eects.
• Double-clicking the button in
the rhythm mode will exit the
rhythm mode and enter the static
mode.
Microphone

INSTALLATION
⚠ INDOOR USE ONLY
1. Peel o one side of the adhesive tape and
stick it to the back of a light.
2. Connect the controller to the IN port (with
the arrow pointing into it) on the back of the
light. Run the cable through a cable
management clip along the edge of the
light.
3. Insert the large connector tip of a
connection cable to one of the OUT ports
(with the arrow pointing out of it). Run the
cable through a cable management clip.
light controller

INSTALLATION
4. Peel o the other side of the adhesive tape
and gently press the light on the wall for 30
seconds.
⚠ Ensure the wall or other surface is free of
dust and water before installing
5. Stick an adhesive tape to the back of the next
light.
•Attach a connection cable to the OUT port.
• Attach the connection cable from the
previous light to the IN port.
• Peel o the other side of the adhesive tape and
press the light on the wall for 30 seconds.
6. Repeat step 5 for other lights and complete
your design.
7. Connect the power adaptor to the controller.
8. Connect the power adapter to a power source
and press the Power button on the controller
to turn on the lights.
continued...

CONNECT WITH THE APP
1. Get the app.
2. Register or login to app.

CONNECT WITH THE APP
continued...
4. Turn on Bluetooth and Wi-Fi on your
smartphone. Make sure you are connected
to a 2.4GHz Wi-Fi access point.
3. Recommended app settings.
Only 2.4G Wi-Fi
networks are supported

CONNECT WITH THE APP
continued...
5. Connecting lights to app.
1
1
2
2
TIP
Press and hold POWER
button for 10 seconds to
enter pairing mode. Triangle
lights will illuminate. Follow
the app prompts to pair
Triangle lights to phone app.
AmbiColour Smart
Triangle Lights
AmbiColour Smart
Triangle Lights
AmbiColour Smart
Triangle Lights
Connect Smarthome

CONNECT WITH THE APP
continued...
6. Controlling lights with the app.
Edit name
All lights
synchronization
Colourful light
ON/OFF
Adjust Brightness (1%-100%)
Turn On/ O a
specic light of
your choice.
Erase DIY
Adjust DIY
Colour
Adjust or
erase DIY
colours
on the
COLOUR
DIY
AmbiColour Smart Triangle Lights

CONNECT WITH THE APP
continued...
44 Preset
scenes
available
Light colours will
change with the
music beats of
your microphone
Create your own
plan
If your light has been
cut during use, you
can adjust the actual
length to better set
up the light strip
Create your
own custom
light sequence.
PRESET
SCENE
MUSIC SCHEDULE ACTUAL POINT
DIY
SCENE

CONNECT WITH THE APP
continued...
7. Removing light from app.
SCROLL
DOWN
AmbiColour Smart
Triangle Lights
AmbiColour Smart Triangle Lights

THE SMART TRIANGLE LIGHTS DO NOT
APPEAR ON THE APP
• If lights are not ashing rapidly, hold down
the power button (about 4 seconds) until
they ash once. Then wait for 2 seconds until
they start ashing rapidly to enter the pairing
mode.
• Enable Bluetooth and Wi-Fi are enabled on
your smartphone.
• Ensure that the Wi-Fi signal is strong where it
is being installed.
• Make sure you are connected to a 2.4GHz
Wi-Fi network.
• Most modems/routers support both 2.4GHz
and 5GHz bands and may use the same Wi-Fi
network name (SSID) for both bands. Log into
the router’s settings and check
• Is 2.4GHz band enabled?
• If both 2.4GHz and 5GHz bands are
TROUBLESHOOTING

using the same SSID, nd the settings
that allow you to separate the 2.4GHz
and 5GHz bands. Usually, there will
be an option to congure each band
individually. Change the SSID for one or
both bands to make them distinct. For
instance, “NetworkName_2.4GHz” and
“NetworkName_5GHz”.
• If you are using Telstra Smart Modem, refer to
the following guide to resolve band steering
issues: https://www.laserco.com.au/Telstra-
NBN-Gen-Smart-Modem-Fix
TROUBLESHOOTING
continued...

1. For indoor use only.
2. This light panel is best used on smooth, dry
surfaces and should not be applied to
uneven or wet surfaces.
3. Ensure the surface is completely dry before
applying the light panel.
4. Gently press the central point of the light
panel against the wall for 30 seconds to
maximise adhesion.
5. Avoid installing the lights above heat
sources in areas where direct sunlight, air
ow, and temperature changes signicantly.
6. To prevent tripping, do not leave the power
cord on the oor.
7. This product is not a children’s toy.
Adult supervision is recommended.
WARNINGS AND CAUTIONS

Power adaptor AC 220-240V, 50/60Hz
Wi-Fi Standard 802.11 b/g/n
Wi-Fi Frequency 2.4GHz
Bluetooth version 5.0
Weight 100g
SPECIFICATIONS

www.connectsmarthome.com.au
Check us out at
Visit our website