Connect CSH-9BAR-262 User manual

AmbiColour Smart Light Bars
CSH-9BAR-262
User Manual

WHAT’S IN THE BOX
• Smart bar light x 9
• Connector switch
• Connector x 8
• Double-sided adhesive sticker x 9
• AC adaptor
• User manual
What you will need:
• Smartphone or tablet with Bluetooth
and connected to 2.4GHz band Wi-Fi
network
• Password for the Wi-Fi network

Controller Switch
OVERVIEW
1. Switch to color
light
2. Switch to
white light
3. Press it to turn down
the luminance of light
4. Press it to turn
up the luminance
of light
5. Press it to
enter music
sync mode
6. Power button: Press
to turn on/o light, long
press to enter
conguration mode
7. Press it to enter or switch over the scene mode
12
34
56
7

INSTALLATION
⚠ INDOOR USE ONLY
•We recommend that you create your design
in another location (like on a table,) before you
bring it to the wall.
1. Stick adhesive tapes to the bottom of
connectors by peeling o one side.

2. Create your design.
Two splicing methods support:
•Insert the light strip from the side.
•Open the cover of the connector and insert
the light strip from the front.
3. Create your design.
⚠ Make sure to attach on smooth, dry
surfaces and not on uneven or wet surfaces
INSTALLATION
continued...

4. Connect the power adaptor to the
connector switch. Then, plug in the power
adaptor.
5. Press the Power button on the controller to
turn on the lights.
INSTALLATION
continued...

CONNECT WITH THE APP
1. Get the app.
2. Register or login to app.

CONNECT WITH THE APP
continued...
4. Turn on Bluetooth and Wi-Fi on your
smartphone. Make sure you are connected
to a 2.4GHz Wi-Fi access point.
3. Recommended app settings.
Only 2.4G Wi-Fi
networks are supported

1
2
AmbiColour Smart
Light Bars
AmbiColour
Smart Light Bars
CONNECT WITH THE APP
continued...
5. Connecting lights to app.
1
2
TIP
If light not ashing, hold
down power button until
light blinks rapidly to
enter pairing mode.
1
2
Connect Smarthome
AmbiColour Smart
Light Bars AmbiColour Smart
Light Bars
TIP
When connected, the
light will stop blinking
and stay lit.
AmbiColour
Smart Light Bars

CONNECT WITH THE APP
continued...
6. Controlling lights with the app.
AmbiColour Smart
Light Bars
AmbiColour Smart
Light Bars

AmbiColour Smart
Light Bars
CONNECT WITH THE APP
continued...
7. Removing light strip from the app.
SCROLL
DOWN
AmbiColour Smart
Light Bars

THE SMART LIGHT BARS DO NOT
APPEAR ON THE APP:
• If the controller’s light is not blinking
rapidly, hold down the power button until the
light ashes rapidly to reset it.
• Enable Bluetooth and Wi-Fi are enabled on
your smartphone.
• Ensure that the Wi-Fi signal is strong where it is
being installed. If not move the lights closer to
the Wi-Fi access point temporarily.
• Make sure you are connected to a 2.4GHz
Wi-Fi network.
Most modems/routers support both 2.4GHz
and 5GHz bands and may use the same Wi-Fi
network name (SSID) for both bands. Log into
the router’s settings and check:
• Is 2.4GHz band enabled?
TROUBLESHOOTING

• If both 2.4GHz and 5GHz bands are using
the same SSID, nd the settings that allow
you to separate the 2.4GHz and 5GHz bands.
Usually, there will be an option to congure
each band individually. Change the SSID for
one or both bands to make them distinct. For
instance, “NetworkName_2.4GHz” and
“NetworkName_5GHz”.
• If you are using Telstra Smart Modem, refer to
the following guide to resolve band steering
issues: https://www.laserco.com.au/Telstra-
NBN-Gen-Smart-Modem-Fix
TROUBLESHOOTING
continued...

1. For indoor use only.
2. This panel is best used on smooth, dry
surfaces and should not be applied to
uneven or wet surfaces.
3. Ensure the surface is completely dry before
applying the light panel.
4. Gently press the central point of the
connector against the wall for 30 seconds to
maximize the addition.
5. Avoid installing the object above heat
sources in areas where direct sunlight, air
ow, and temperature changes signicantly.
6. Don’t leave the power cord on the oor to
prevent tripping.
7. Children must be supervised by an adult
when using this product.
WARNINGS AND CAUTIONS

Dimensions - 1x
bar light (LxWxH) 270x16x10 mm
Power adaptor
input: AC 100-240V
50/60Hz
output: 12V 2A (max.)
Wi-Fi Standard 802.11 b/g/n
Wi-Fi Frequency: 2.4GHz
Wi-Fi Standard 802.11 b/g/n
Bluetooth 5.1
SPECIFICATIONS

www.connectsmarthome.com.au
Check us out at
Visit our website