CONSET 501-23 Installation instructions

501-23 Original
350490.0
EN - Assembly Instruction and User Manual (Page 2)

TABLE OF CONTENTS
1. Safety and warnings
2. Usage
3. Set up and installation
4. Operation
5. Maintenance and defects
6. Technical data
7. Parts
8. Assembly instructions
9. Declaration of conformity
IMPORTANT NOTES!
Prior to installment, use and
maintenance of the table frame, any
installer and any user of the table
must study this assembly and
operation manual carefully, so as to
gain a complete understanding of its
contents
1. Safety and warnings
This table complies with the prescribed safety regulations. Inappropriate use may cause damage to persons and table.
Please read the operation manual prior to start using the table. It provides you with important information about safety, use,
installation and maintenance of the table, and thus protecting you and your children and avoiding damage on the table.
Please guard this operation manual and pass it on to any future owner!
2. Usage
The electromotive, height-adjustable tables are designed for workstations in dry work environments only (0-40°C; 20-90% relative
humidity). The table height is infinitely adjustable, so that it can be set to the most ergonomically suitable working level:
They have not been designed for other purposes than those included in this manual, e.g. they are not to be used in areas of high
humidity or dampness, nor for lifting people. Any other use is at one’s own risk!
•
Do not crawl, lie or move around under the table frame, and do not sit or stand on the table frame.•
CHILDREN should only use the table when supervised by adults.•
Liability - The manufacturer accepts under no circumstances warranty claims or liability claims for damages arising from
improper use or handling of the table frame other than that described in this operation manual.
•
3. Set up and installation
When the table has been assembled (see assembly instructions in CHAPTER 8) the adjustable feet are installed so that the table
is level and does not shift. Then the table is connected to the 100-240 VAC outlet and the table is ready for use.
•
Make sure that no cables can get jammed.•
Place the table in a safe distance from window frames, radiators, furniture etc. so that people do not get stuck.•
Do not place any objects above 21" (55 cm) underneath the table.•
When moving the table after it has been assembled, the tabletop needs to be removed. The table CANNOT be lifted by the
tabletop. The desk need to be lowered to minimum height before moving.
•
4. Operation
UP/DOWN operation:
Push the buttons for operation up or down
WARNING: FAILURE TO COMPLY WITH OR OBSERVE ALL ASSEMBLY, SAFETY AND OPERATION INSTRUCTIONS AND
WARNINGS REGARDING THE USE OF THIS PRODUCT MAY RESULT IN SERIOUS BODILY INJURY.
2

5. Maintenance and defects
The table does not require any maintenance by usage as described in chapter 2 in the directions for use.•
The table is only to be maintained with a damp cloth•
In the event of the occurrence of jarring sounds during operation, STOP using the table and please contact the dealer.•
6. Technical data
Frame, materials Steel, powder lacquered
Weight, frame 45 kg
Width, frame 132-192 cm
Depth, frame 66 cm
Height 68-120 cm
Max. load 175 kg
Speed 22 mm/sec. unloaded
Duty cycle 10% by 50% of max. load on frame or max. 2 min. contiuouesly
Operation Micro switches
Voltage 100-240 VAC | 50/60 Hz
Standby Consumption <0,15 Watt
7. Parts
See page 4.
8. Assembly instructions
See page 5 - 6.
9. Declaration of conformity
We hereby declare, under our sole responsibility that the following products:
Sit and stand table product type 501-23•
is in accordance with:
DIRECTIVE 2006/42/EF OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL of 17 May 2006 on machinery and on changes of
directive 95/16/EF.
•
DIRECTIVE 2014/30/EU OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL of 26 February 2014 on the harmonization of
the laws of the Member States relating to electromagnetic compatibility.
•
DIRECTIVE 2011/65/EU OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL of 8 June 2011 on the restriction of the use of
certain hazardous substances in electrical and electronic equipment (recast).
•
With reference to the above please be aware that:
the sit and stand table is considered a machine and•
the sit and stand table may not be used until it has been assembled and installed according to the instructions.•
Manufacturer
ConSet A/S | Industrivej 23 | 6900 Skjern | Denmark
www.conset.com | Tlf.: [phone] | [email protected]
3

7. Parts
Lifting column
x2
Foot
x2
Tabletop support
x3
Travers end section
x2
Travers middle section
x1
Screw M6x12mm
x32
Screw M6x12mm
x4
Sync box
x1
Extender wire
x3
Power supply
x1
Power cord
x1
Control panel
x1
Wooden screw 5x16mm
x12
Wirenail
x4
4

8. Assembly Instruction and User Manual
Travers assembly
Column assembly
5

Column to travers
It is important to tighten all screws to get best possible stability.
Wiring
See also user manual packed along the Power and Control components.
6

7

8