CONSET 501-49 Manual

1
ELECTRIC HEIGHT ADJUSTABLE DESK
CONSET – MODEL: 501-49
DIRECTIONS FOR USE / ASSEMBLING
IMPORTANT NOTES!
Prior to installment, use and maintenance of the table frame, any installer and any user of the table must study
this assembly and operation manual carefully, so as to gain a complete understanding of its contents.
334130.0
EN
WARNING
WARNING: FAILURE TO COMPLY WITH OR OBSERVE ALL
ASSEMBLY, SAFETY AND OPERATION INSTRUCTIONS
AND WARNINGS REGARDING THE USE OF THIS
PRODUCT MAY RESULT IN SERIOUS BODILY INJURY.

2
TABLE OF CONTENT
1. SAFETY AND WARNINGS
2. USAGE
3. SET UP AND INSTALLATION
4. OPERATION
5. MAINTENANCE AND DEFECTS
6. TECHNICAL DATA
7. PARTS
8. ASSEMBLY DIRECTIONS
9. DECLARATION OF CONFORMITY
1. SAFETY AND WARNINGS
2. USAGE
The electromotive, height-adjustable tables are designed for workstations in dry work environments only
(0-40°C; 20-90% relative humidity). The table height is infinitely adjustable, so that it can be set to the
most ergonomically suitable working level.
They have not been designed for other purposes than those included in this manual, e.g. they are not to
be used in areas of high humidity or dampness, nor for lifting people.
Any other use is at one’s own risk!
Do not crawl, lie or move around under the table frame, and do not sit or stand on the table
frame.
CHILDREN should only use the table when supervised by adults.
Liability: The manufacturer accepts under no circumstances warranty claims or liability claims for
damages arising from improper use or handling of the table frame other than that described in this
operation manual.
3. SET UP AND INSTALLATION
When the table has been assembled (see assembly directions in CHAPTER 8) the adjustable feet are
installed so that the table is level and does not shift. Then the table is connected to the 100-240 VAC outlet
and the table is ready for use.
Make sure that no cables can get jammed.
Place the table in a safe distance from window frames, radiators, furniture etc. so that people do not get
stuck.
Do not place any objects above 55 cm underneath the table.
When moving the table after it has been assembled, the table top needs to be removed. The table
CANNOT be lifted by the table top.
4. OPERATION
UP/DOWN operation:
Push the buttons for
operation up or down
This table complies with the prescribed safety regulations. Inappropriate use may cause damage to
persons and table.
Please read the operation manual prior to start using the table. It provides you with important
information about safety, use, installation and maintenance of the table, and thus protecting you
and your children and avoiding damage on the table.
Please guard this operation manual and pass it on to any future owner!

5. MAINTENANCE A
ND DEFECTS

The table does not require any maintenance by usage as described in chapter 2 in the directions for use.

The table is only to be maintained with a wrung cloth.

In the event of the occurrence of jarring sounds during operation, STOP using the table and
contact the dealer.
6. TECHNICAL DATA
Frame, materials:
Weights:
W
D
H (frame)
V (speed)
F
MAX
= Max. load:
Duty cycle:
Operation:
Voltage:
Standby Consumption:
Above specifications may vary depending on local temperature,
7. PARTS
F
MAX
1a
1b
2
3
ND DEFECTS
The table does not require any maintenance by usage as described in chapter 2 in the directions for use.
The table is only to be maintained with a wrung cloth.
In the event of the occurrence of jarring sounds during operation, STOP using the table and
Steel, Powder lacquered / Chrome
23 kg (Packaging total 25 kg)
120-200cm
70-120 cm (depends on top shape).
63-123 cm
~ 32mm/sec. (unloaded)
100 kg (on frame)
10% by 50% of max load on frame
or max 2 min. continuously
Micro switches
100-240 VAC / 50/60Hz
< 1 Watt
Above specifications may vary depending on local temperature,
humidity and input voltage.
W
D
H
b) x 2
3
4
5
6
8
9
c) x 1
a) x 2
7
The table does not require any maintenance by usage as described in chapter 2 in the directions for use.
In the event of the occurrence of jarring sounds during operation, STOP using the table and
please
or max 2 min. continuously
d) x 16
f) x 2
e) x 4

4
2
continued ….
3
7
9
1b
1a
8
7
1
2
8. ASSEMBLY DIRECTIONS
1
e) x 4
6

5continued ….
continued …..
4
5
a) x 2
b) x 2
c) x 1
5

6
9. DECLARATION OF CONFORMITY
We hereby declare, under our sole responsibility that the following products:
-ConSet sit and stand table product type 501-49
is in accordance with:
-Directive 2006/42/EF of The European Parliament and of the Council of 17 May 2006 on machinery and
on changes of directive 95/16/EF
With reference to the above please be aware that:
-the sit and stand table is considered a machine and
-the sit and stand table may not be used until it has been assembled and installed according to the
instructions.
Manufacturer:
ConSet A/S
Staalvej 14-16
DK-6900 Skjern
Denmark
Tel: [phone], Fax: [phone]
www.conset.com, [e-mail]
6
d) x 16
continued …..
2
4
3
Wire guide
The table is now assembled. Follow the directions for use in
CHAPTER 2.
f) x 2