Contec IPC-DT 61 User manual

IPC Series
Flat Panel Display
IPC-DT/61 Series
User’s Manual
CONTEC CO.,LTD.

Copyright
Copyright 2004 CONTEC CO., LTD. ALL RIGHTS RESERVED.
No part of this document may be copied or reproduced in any form by any means without prior written
consent of CONTEC CO., LTD.
CONTEC CO., LTD. makes no commitment to update or keep current the information contained in this
document. The information in this document is subject to change without notice.
All relevant issues have been considered in the preparation of this document. Should you notice an
omission or any questionable item in this document, please feel free to notify CONTEC CO., LTD.
Regardless of the foregoing statement, CONTEC assumes no responsibility for any errors that may
appear in this document nor for results obtained by the user as a result of using this product.
Trademarks
MS, Microsoft, MS-DOS and Windows are trademarks of Microsoft Corporation. Other brand and
product names are trademarks of their respective holder.
User’s Manual i

Table of Contents
Copyright .............................................................................................................................................i
Trademarks ..........................................................................................................................................i
Table of Contents................................................................................................................................ii
1. Introduction 1
Features...............................................................................................................................................1
Customer Support...............................................................................................................................2
Web Site.......................................................................................................................................2
Limited One-Year Warranty............................................................................................................... 2
How to Obtain Service ....................................................................................................................... 2
Liability ..............................................................................................................................................2
Safety Precautions ..............................................................................................................................2
Safety Information.......................................................................................................................3
Handling Precautions................................................................................................................... 3
2. Specifications 7
Function Specifications ......................................................................................................................7
General Specifications........................................................................................................................9
Optical Display Specifications.........................................................................................................10
3. Outside Dimensions and Part Names 11
Outside Dimensions..........................................................................................................................11
Part Names........................................................................................................................................15
Analog RGB Connector............................................................................................................. 18
RS Touch Panel Connector........................................................................................................18
USB Touch Panel Connector.....................................................................................................19
DVI-D Connector ......................................................................................................................20
4. Hardware Setup 21
Installation Requirements................................................................................................................. 21
Panel Cut........................................................................................................................................... 21
Attaching the Fitting Used to Attach to the Main Unit............................................................. 23
5. Connection to the Host Computer 25
Analog RGB Connection..................................................................................................................25
DVI-D Connection ........................................................................................................................... 26
Touch Panel Data Communications.................................................................................................29
ii User’s Manual

6. Power Supply Connection 31
AC input type ................................................................................................................................... 31
DC input type ................................................................................................................................... 32
Power Supply Connector........................................................................................................... 32
AC Adapter Jack........................................................................................................................ 33
AC adapter code removal prevention fitting.................................................................................... 34
7. Screen Adjustment and a Setup 35
Menu Screen..................................................................................................................................... 35
Direct Key......................................................................................................................................... 40
Memory of a Setting Value.............................................................................................................. 40
8. LED Indicators 41
9. Touch Panel 43
USB Multi-Touch Panel................................................................................................................... 44
10. Display Mode 45
11. Options 47
User’s Manual iii

iv User’s Manual

1. Introduction
1. Introduction
This product is a dual-input (analog RGB and DVI-D), panel-mounted, color TFT LCD display unit for use
with host computers such as the CONTEC IPC series and SBCs (single board computers).
Features
- Full-bright, wide-angle-of-visibility type of liquid crystals capable of displaying up to 262,144
colors (16,777,216 colors on the IPC-DT/H61XT-DC1 and AC0)
- Standard analog RGB input for screen. RS-232C and USB interfaces for touch panel.
- Multiple touch panel configurations containing up to eight touch panels are supported when using
the USB touch panel interface.
- Auto-scaling feature that resizes the input screen to the LCD dot configuration.
- On-screen display setup menu facilitating screen adjustment
- Dual-input function supports analog RGB and DVI-D inputs. The display can be connected to two
different computers at once. (Simultaneous display is not supported. Screens are switched using the
OSD.)
- Analog touch panel enabling mouse emulation using driver software
- Optional AC adapter (IPC-ACAP12-01) available for AC power supply.
- Front structure with IP65-compliant ingress protection
- Optional stand kit available for desktop use.
- A special fitting is provided to prevent the AC adapter cable from being unplugged.
User’s Manual 1

1. Introduction
Customer Support
CONTEC provides the following support services for you to use CONTEC products more efficiently and
comfortably.
Web Site
Japanese http://www.contec.co.jp/
English http://www.contec.com/
Chinese http://www.contec.com.cn/
Latest product information
CONTEC provides up-to-date information on products.
CONTEC also provides product manuals and various technical documents in the PDF.
Free download
You can download updated driver software and differential files as well as sample programs available in
several languages.
Note! For product information
Contact your retailer if you have any technical question about a CONTEC product or need its price,
delivery time, or estimate information.
Limited One-Year Warranty
CONTEC Products are warranted by CONTEC CO., LTD. to be free from defects in material and
workmanship for up to one year from the date of purchase by the original purchaser.
Repair will be free of charge only when this device is returned freight prepaid with a copy of the original
invoice and a Return Merchandise Authorization to the distributor or the CONTEC group office, from
which it was purchased.
This warranty is not applicable for scratches or normal wear, but only for the electronic circuitry and
original products. The warranty is not applicable if the device has been tampered with or damaged
through abuse, mistreatment, neglect, or unreasonable use, or if the original invoice is not included, in
which case repairs will be considered beyond the warranty policy.
How to Obtain Service
For replacement or repair, return the device freight prepaid, with a copy of the original invoice. Please
obtain a Return Merchandise Authorization Number (RMA) from the CONTEC group office where you
purchased before returning any product.
* No product will be accepted by CONTEC group without the RMA number.
Liability
The obligation of the warrantor is solely to repair or replace the product. In no event will the warrantor
be liable for any incidental or consequential damages due to such defect or consequences that arise from
Safety Precautions. Understand the following definitions and precautions to use the product safely.
Safety Precautions
Understand the following definitions and precautions to use the product safely.
2User’s Manual

1. Introduction
Safety Information
This document provides safety information using thefollowing symbols to prevent accidents resulting in
injury or death and the destruction of equipment and resources. Understand the meanings of these labels
to operate the equipment safely.
DANGER DANGER indicates an imminently hazardous situation which, if not avoided, will
result in death or serious injury.
WARNING WARNING indicates a potentially hazardous situation which, if not avoided, could
result in death or serious injury.
CAUTION CAUTION indicates a potentially hazardous situation which, if not avoided, may
result in minor or moderate injury or in property damage.
Handling Precautions
CAUTION
- As this product contains precision electronic components, do not use or store in environments
subject to shock or vibration.
- Do not use or store the product in a location such as extremely high or low temperature, rapid
temperature changes, and the place which receives a strong ultraviolet ray.
Example: - Exposure to direct sun
- In the vicinity of a heat source
- Some products require configuration settings. Always check these requirements before use. Also,
never set switches or jumpers to other than the specified settings as this may cause a fault.
- Do not use or store the equipment in a dusty or humid place.
- If you discover damaged or missing items, contact your retailer.
- Do not perform key operations with the touch panel to implement a process that might endanger life
or result in serious damages. Design a system that can cope with incorrect key input operations.
- Do not use a sharp-edged object, such as a mechanical pencil, to operate the touch panel in order to
prevent scratching or malfunctions.
- Protect the touch panel against shock to prevent damage.
- CONTEC is not liable for a product that has been modified by the user.
- For this equipment, use the dedicated power supply unit if possible. If you connect any other power
supply unit, be sure to select the one that satisfies the voltage and current capacity standards.
- Never supply power to the power supply connector and the AC adapter jack at the same time as it
can cause a fault.
User’s Manual 3

1. Introduction
- When the surface or frame of the touch panel has become dirty, wipe it with neutral detergent. Do
not wipe the touch panel with thinner, alcohol, ammonia, or a strong chlorinated solvent.
- Do not plug or unplug the connector with the equipment powered on. as doing so may result in a
malfunction or fault.
- This product is not intended for use in aerospace, space, nuclear power, medical equipment, or other
applications that require a very high level of reliability. Do not use the product in such applications.
- If you utilize this product in such usages where high reliability and safety are required as on the
trains, vessels, automotives or crime- or disaster-prevention devices, contact your retailer.
Use environment
This product operates under the following operating systems:
Windows XP/2000/NT 4.0/98SE/95OSR2, MS-DOS 6.2
* The touch panel USB interface is only supported on Windows XP/2000/98SE.
Life expectancy of components
(1) Backlight--- Display brightness decreases over time with use. The operating life of the backlight
(brightness reduced to 50% of original) is 50,000 hours for all models. (Assuming
continuous operation at 25 degrees centigrade.)
(2) Touch panel--- The operating lifetime of the touch panel is at least 1 million touches (as tested by
mechanical touching under 300g of force at a rate of two presses per second).
(3) Power supply (AC adapter) --- Expected life is six years for continuous operation at 40°C (when
mounted horizontally). However, this life may be reduced
depending on the operating temperature (in the case of higher
temperatures).
* CONTEC accepts your request for replacing each consumable in the PANECON-PC as a requestfor
repair (at an additional cost). Contact your local retailer or CONTEC sales office.
LCD Display Pixel Drop
LCD display may have some pixels being dropped (bright and black spots) below a certain threshold.
Note that this is not a failure or a defect.
Burn-in on TFT Display
"Burn-in" may occur if the same display is retained for a long time. Avoid this by periodically
switching the display so that the same display is not maintained for a long time.
* Burn-In: Phenomenon characterized by a TFT display as a result of long-time display of the same
screen where a shadow-like trace persists because electric charge remains in the LCD element even
after the patterns are changed.
4User’s Manual

1. Introduction
Connecting to a host with an existing touch panel function such as a CONTEC panel computer.
This touch panel cannot be used with a touch panel mounted in the host computer. In this case, the
touch panel function will be unavailable but screen display will still work normally.
However, on the following CONTEC panel computers, multiple touch panels can be used together
when connected via the USB interface.
- IPC-PT/630 Series: IPC-PT/H630X(PCI)C, IPC-PT/H630X(PCI)CP ,
IPC-PT/L630S(PCI)C, IPC-PT/L630S(PCI)CP
- IPC-PT/620 Series: IPC-PT/H620X(PCW)C, IPC-PT/H620X(PCW)CP ,
IPC-PT/L620S(PCW)C, IPC-PT/L620S(PCW)CP
- IPC-PT/600 Series: IPC-PT/H600X(PCW)C, IPC-PT/H600X(PCW)P ,
IPC-PT/L600S(PCW)C, IPC-PT/L600S(PCW)P
User’s Manual 5

1. Introduction
6User’s Manual

2. Specifications
2. Specifications
Function Specifications
Table 2.1. Function Specifications Specification
Item IPC-DT/S61VT-DC1 IPC-DT/M61VT-DC1
IPC-DT/M61VT-AC0
IPC-DT/L61SVT-DC1
IPC-DT/L61SVT-AC0
IPC-DT/H61XT-DC1
IPC-DT/H61XT-AC0
Screen
Assembly type Panel mounted, desktop *1
Screen size 6.5 inches 10.4 inches 12.1 inches 15.0 inches
Number of pixels 640 x 480 dots 640 x 480 dots 800 x 600 dots 1024 x 768 dots
Display type TFT Color LCD
Number of colors 262,144 colors 262,144 colors 262,144 colors 16,777,216 colors
Screen adjustment Automatic adjustment (display positioning and scaling) and manual
adjustment using the front switches
Brightness control Adjustment using the front switch or software control from the host computer
Backlight control Can be turned on or off by an OSD switch or via software control from the host
computer.
Display interface Analog RGB input HD-SUB 15 pin (Female) connector
DVI-D input 24 pin DVI (Female) connector
Analog
RGB input Separate RGB, analog, positive polarity 0.7Vp-p/75Ω Separate V/H, TTL, positive/negative polarity
Horizontal: 31 - 80kHz, vertical: 56 - 75Hz
Incoming
signal
specification
DVI-D input Digital RGB (complies with TMDS) *2
Cable length which recommends 5mm or less *3
Touch panel
Resolution 4096 x 4096
Detection method Resistive-layer analog method
Touch life expectancy One million repeated touches (silicon rubber load of 3 N)
Touch panel interface Connect to the host computer using either USB*4 or RS-232C.
USB: USB1.1-compliant, TypeB Connector
RS-232C: 9pin D-SUB (Male) Connector
Touch panel driver
(option) For Windows: IPC-SLIB-01 For MS-DOS: IPC-TPB1-DRV
*1 Optional desk stand IPC-SND-03 allowing desktop installation
*2 If the output is from a CONTEC IPC series or SBC series model, an ISA bus type panel link I/F board
(ADPLNK(PC)H) is required for some models. Please confirm before purchasing.
*3 Using a cable longer than 5 m may reduce the image quality. The cable should be as short as possible as
degradation. in image quality may result even when the cable is 5 m or shorter depending on the type of host
computer or cable.
*4 The touch panel USB interface is only supported on Windows XP/2000/98SE.
User’s Manual 7

2. Specifications
Table 2.2. Power Supply Specifications (DC Input Type) Specification
Item IPC-DT/S61VT-DC1 IPC-DT/M61VT-DC1 IPC-DT/L61SVT-DC1 IPC-DT/H61XT-DC1
Power supply input part
Power supply connector 4-pin nylon connector for 12 VDC power supply
AC adapter jack AC adapter jack for 12 VDC power supply (An optional AC adapter (IPC-ACAP12-01) can be used for 100 - 240VAC
input.)
Input power supply voltage +12VDC±5%
Consumption current 1.3A(Max.) 1.4A(Max.) 1.6A(Max.) 2.5A(Max.)
Consumption current
(power save mode) 0.4A(Max.)
Table 2.3. Power Supply Specifications (AC Input Type) Specification
Item IPC-DT/M61VT-AC0 IPC-DT/L61SVT-AC0 IPC-DT/H61XT-AC0
Power supply input part
Power supply connector Three-pin terminal block for the AC power supply
Input power supply voltage Auto-switched 85 - 132VAC / 170 - 265VAC (47 - 63Hz) input
Power consumption 36VA (Max.) 40VA (Max.) 60VA (Max.)
Current consumption
(power save mode) 14VA (Max.)
8User’s Manual

2. Specifications
General Specifications
Table 2.4. General Specifications
Item Specification
Environment
Operating
temperature 0 - 50ºC (0 - 40ºC when using an IPC-ACAP12-01 (AC switching adapter))
Storage
temperature -10 - 60ºC
Operating humidity (20 - 80% when using an IPC-ACAP12-01 (AC switching adapter))
(No condensation allowed)
Floating dust Normal
Corrosive gas None
Line noise
AC line: 2 kV, Signal line: 1 kV
(IEC1000-4-4Level3, EN61000-4-4Level3)
(HOST: IPC-BX/M600(PCW) Power supply: IPC-POA200/12-01)
Noise
resistance Electrostatic
withstanding
voltages
Contact: 4 kV(IEC1000-4-2Level2, EN61000-4-2Level2)
Airborne: 8 kV(IEC1000-4-2Level3, EN61000-4-2Level3)
(HOST: IPC-BX/M600(PCW) Power supply: IPC-POA200/12-01)
Vibration
resistance Sweep durability
10 - 57 Hz/Single-side amplitude or 0.15 mm
57 - 150 Hz/2.0 G in the X/Y/Z directions for 23 minutes each
(Conforming to JIS C0040 and IEC68-2-6)
Shock resistance 10 G in the X/Y/Z directions for 11 ms; Half-sine wave
(Conforming to JIS C0041 and IEC68-2-27)
Table 2.5. Structure specification (DC Input Type)
Specification
Item IPC-DT/S61VT-DC1 IPC-DT/M61VT-DC1 IPC-DT/L61SVT-DC1 IPC-DT/H61XT-DC1
Structure
Major dimension (mm) 210(W) x 40(D) x
166(H) 305(W) x 43.5(D) x 240(H) 316(W) x 46.5(D) x 256(H) 376(W) x 46(D) x 305(H)
Panel cut dimensions
(mm) 199.0(W) x 155.0(H) 292.0(W) x 227.0(H) 303.0(W) x 243.0(H) 358.0(W) x 289.0(H)
Mountable panel
thickness 1.6mm - 7mm
Weight 1.3kg 2.6kg 2.9kg 3.9kg
Ingress protection Front part conforming to IP65
Table 2.6. Structure specification (AC Input Type)
Specification
Item IPC-DT/M61VT-AC0 IPC-DT/L61SVT-AC0 IPC-DT/H61XT-AC0
Structure
Major dimensions (mm) 305(W) x 51.5(D) x
240(H) 316(W) x 54.5(D) x 256(H) 376(W) x 54(D) x 305(H)
Panel cut dimensions
(mm) 292.0(W)×227.0(H) 303.0(W)×243.0(H) 358.0(W)x289.0(H)
Mountable panel
thickness 1.6mm - 7mm
Weight 2.8kg 3.1kg 4.1kg
Ingress protection Front part conforming to IP65
User’s Manual 9

2. Specifications
Optical Display Specifications
Table 2.7. Optical Display Specifications
Specifications (25ºC Typ. Value)
Item Condition IPC-DT/S61VT-DC1 IPC-DT/M61VT-DC1
IPC-DT/M61VT-AC0
IPC-DT/L61SVT-DC1
IPC-DT/L61SVT-AC0
IPC-DT/H61XT-DC1
IPC-DT/H61XT-AC0
φ=180° 45deg 50deg 50deg 45deg
Visual angle
(vertical) φ=0° 35deg 70deg 70deg 55deg
φ=+90° 50deg 70deg 70deg 60deg
Visual angle
(horizontal) CR≥10
φ=-90°
Display in
monochrome
50deg 70deg 70deg 60deg
Surface
brightness
(at center) Display in white 300cd/m2400cd/m2350cd/m2260cd/m2
*1 Surface brightness is a numerical value in a display simple substance.
The brightness that let the touch panel pass serves as about 75% of the above-mentioned numerical value.
Left
( φ=
- 90o )
Z
Y
X
Top
( φ= 180o )
Right
( φ= 90o )
Bottom
( φ = 0o )
( θ= 0o )
Measurement direction
θ
Module
φ
Figure 2.1. Viewing Range Definition
CAUTION
The above optical specification data shows optical characteristics of the liquid crystal in the display;
the data does not represent the actual view on the display or its viewing angles.
10 User’s Manual

3. Outside Dimensions and Part Names
3. Outside Dimensions and Part Names
Outside Dimensions
IPC-DT/S61VT-DC1
INPUT : XXXXXXXXXXXXXXXXXX
XXXXXX XXX
XXXXXX XXX
MODEL :
SERIAL No.: XXXXXXXXXXXXX
XXXXXXXXXXXXXXXXXX
XXXXXXXXX
P ES CN
TI
PASS
CAUTION!
*************
The screw bolt ing torque of attachment
******0.6N*m***
mustbe0.6N-m(MAX)
M3 TAP
4-M4 TAP
75
75
27
154
198
35
50
16
5
[mm]
210
138
105
58
166
(Maximum tapping
length : 5mm)
(Maximum
tapping length
: 5mm)
ESCMENU -+ POWER
12VDC-IN
2 1COM DVI VGA USB
CAUTION!
12VDC-IN*1*2** *
12VDC-IN sim ultaneously.
Don't connect 1 and2 of
************
Figure 3.1. Outside Dimensions of Main Unit(IPC-DT/S61VT-DC1)
IPC-DT/M61VT-DC1
8-M4 TAP
M3 TAP
FG -+
212VDC-IN1
************ Don't con nect 1 and 2 of 12VDC-IN simult aneo u sly. 12VDC-IN*1*2***
CAUTION!
[mm]
COM USBDVI VG A
27.5
6.5 75
100
100
75
38.5
18.5
5
49
291
226
240
87.7
163.4
216.2
305
ESC
+-
MENU POWE R
(Maximum tapping
length : 5mm)
(Maximum
tapping length
: 5mm)
Figure 3.2. Outside Dimensions of Main Unit (IPC-DT/M61VT-DC1)
User’s Manual 11

3. Outside Dimensions and Part Names
IPC-DT/L61SVT-DC1
41.5
21.5
5
54.5
302
FG -+
212VDC-IN1
************
Don'tcon nect 1 and 2 of 12VDC-INsimultaneously.
12VDC-IN*1*2***
CAUTION!
8-M4 TAP
M3 TAP
242
316
251
96.8
256
189.5
[mm]
100
75
100
27.5
6.5 75
(Maximum tapping
length : 5mm)
(Maximum tapping
length : 5mm)
COM USBDVI V GA
ESC
+-
MEN U POWER
Figure 3.3. Outside Dimensions of Main Unit (IPC-DT/L61SVT-DC1)
IPC-DT/H61XT-DC1
[mm]
(Maximum tapping
length : 5mm)
(Maximum tapping
length : 5mm)
ESC
+-
MENU POWER
233
309
376
305123
M3 TAP
COM U
SB
DVI VGA
357
220
100
100
75
75
8-M4 TAP
288 41 5
21
Figure 3.4. Outside Dimensions of Main Unit (IPC-DT/H61XT-DC1)
12 User’s Manual

3. Outside Dimensions and Part Names
IPC-DT/M61VT-AC0
8-M4 TAP
39.3
67.4
[mm]
226
291 49
5
18.5
38.5
75
100
100
75
6.5
27.5
8
67.5
148 305
216.2
163.4
87.7
240
(Maximum tapping
length : 5mm)
VGADVI USBCOMLN
POWER
MENU -+ ESC
Figure 3.5. Outside Dimensions of Main Unit (IPC-DT/M61VT-AC0)
IPC-DT/L61SVT-AC0
8-M4 TAP
302
54.5
5
21.5
41.5 242
40.367.4
67.5
148
25696.8
189.5
251
316
[mm]
6.527.5 100
75
100
75
8
(Maximum tapping
length : 5mm)
VGADVI U SBCOM
NL
POWER
MENU - + ESC
Figure 3.6. Outside Dimensions of Main Unit (IPC-DT/L61SVT-AC0)
User’s Manual 13

3. Outside Dimensions and Part Names
IPC-DT/H61XT-AC0
VGADVI USBCOM
LN
100
75
148
357
220
75
100
8-M4 TAP
288 67.4
69.3 21
41
85
POWER
MENU - + ESC
233
309
376
123
305
[mm]
(Maximum tapping
length : 5mm)
Figure 3.7. Outside Dimensions of Main Unit (IPC-DT/H61XT-AC0)
14 User’s Manual

3. Outside Dimensions and Part Names
Part Names
XXXXXXXXX
XXXXXXXXXXXXXXXXXX
SERIAL No. : XXXXXXXXXXXXX
MODEL :
XXXXXXXXX
XXXXXXXXX
CAUTION!
The screw bolting torque
of attachment must be
0.6N-m(MAX).
XXXXXXXXXXXXXXXXXXINPUT :
Front
Back
Right side Left side
Screen & Touch panel
Screen adjustment switch
AC adapter jack
Analog RGB connector
RS touch panel connector
USB touch panel connector
DVI-D connector
+12VDC power connector
P
ES
CN
TI
PAS S
POWER LED
USBVGADVICOM
1 2
12VDC-IN
CAUTION!
12VDC-I N*1*2* **
12VDC-IN s imul tane ously .
Don't co nnect 1 and 2 of
************
POWER
+-
MENU ESC
Figure 3.8. Part Names(IPC-DT/S61VT-DC1)
User’s Manual 15