converted SW102 User manual

1
SW102 DISPLAY
USER MANUAL

2
Find us on your favourite social media channels
Tag your posts with #Convertedbikes
FOLLOW THE CONVERTED
LOVE YOUR CONVERTED BIKE?
SHOW US YOUR ADVENTURES
#Convertedbikes

3
DISPLAY OVERVIEW 4
SCREEN LAYOUT/SPECIFICATIONS 5
MAIN USER SCREEN 6-8
-TURNING THE SYSTEM ON AND OFF
-VIEWING THE MAIN USER INFORMATION
-SETTING THE PEDAL ASSIST LEVEL
-LIGHTS
-WALK ALONG
-BATTERY LEVEL INDICATOR
ADJUSTING SETTINGS 9-10
-UNITS
-WHEEL SIZE
-PASSWORD
-AUTO OFF
-ASSIST SPEED-LIMIT SETTING
-BATTERY
-INFO
-FACTORY RESET
DATA RESET 11
FAULTS 12-13
-TROUBLE SHOOTING
-ERROR CODES
CONTENTS

4
DISPLAY OVERVIEW
POWER ON/OFF
ASSIST LEVEL UP
/LIGHTING (2 SEC)
ASSIST LEVEL DOWN
/WALK (2SEC)
MODE
23mm
63mm
Ø22.2mm
40mm
9mm

5
REALTIME INFO
RUNNING SPEED /AVERAGE
SPEED /MAX SPEED
PEDAL ASSIST LEVEL
0 NO ASSIST - 5 MAX ASSIST
BATTERY LEVEL LIGHTS ON/OFF INDICATION
TRIP / ODOMETER
UNITS
SCREEN LAYOUT
SPECIFICATIONS
Power supply: DC 24V/36V/48V
Rated current: 12mA
Screen specication:1.3”OLED, 64x128 pixels
Operating temperature: -20°C ~ 60°C
Storage temperature: -30°C ~ 80°C
Waterproof level: IP65
Note: While this display is IP65 rated, it is recommended that additional
protection is used (a plastic bag over the display works well) if the bike
is on the carrier of a car or if exposed to the elements for extended
periods of time.

6
VIEWING THE MAIN USER INFORMATION
After starting up the display the default main user screen is ‘speed’.
Short presses of the ‘M’ button change the indicated information in
sequence as below:
Trip Distance> Riding TIME >Ave/Max Speed + Odometer Distance>Trip.
TURNING THE SYSTEM ON AND OFF
Ensure the switch on the battery is in the ‘On’ position.
Hold the Display Power button for 2 seconds, then the display will power
on.
With the display on, holding the Power button for 2 seconds will turn off
the system.
Additionally, you can shut the system down by turning the battery off.
MAIN USER SCREEN

7
Hold the + button for 2 seconds to turn on the Converted System riding
lights and display back light. The light symbol will show when on.
Hold the + button for 2 seconds to turn the lights off.
Converted System lights can be purchased from www.converted.co.nz or
dealers.
SETTING THE PEDAL ASSIST LEVEL
Adjusting the assist level sets the amount of motor power that assists
your pedalling.
Press + (UP) or - (DOWN) to change the output power of the motor. The
power ranges from level 0 to level 5. Level 0 deactivates the pedal assist
system. Default start level is 1, Level 5 is the maximum power.
LIGHTS

8
WALK ALONG
Hold the - button down to cause the bike to move along at walking
speed.
BATTERY LEVEL INDICATOR
The 5 battery bars represent the capacity of the battery.
0 Bars/
Flashing
Border
≤5%
5 Bars
≥75%
1 Bar
14-5%
4 Bars
74-55%
3 Bars
54-35%
2 Bars
34-15%

9
Turn the system on, within 10 Seconds press and hold Mode. The screen
will switch to the ‘setting’ menu.
Navigate the menu using short presses of the up/down keys. Select
adjustment sub-menus with a short press of the ‘M’ key.
Use the ‘M’ key and up/down to adjust the associated values(see below).
Press ‘Exit’ to accept a setting and return to the main setting menu.
To exit the settings menu, either select ‘Exit’ or wait 10 seconds for
the display to time-out and automatically revert back to the main user
mode.
UNITS
In the ‘Wheel’ menu, press ‘M’ to select the correct value to match the
wheel diameter. Selectable values include: 14, 16, 18, 20, 22, 24, 26,
27.5, 700C, 28, 29.
Select ‘Exit’ to accept a setting and return to the main setting menu.
In the ‘Unit’ setting menu, use the M button to toggle between KM/H
and MPH
Select ‘Exit’ to accept a setting and return to the main setting menu.
Enter and adjust within the settings menu.
SETTINGS
WHEEL (SIZE)
2. Press and hold
Immeditiately after startup
(before 10 seconds)
1.

10
PASSWORD
For added security, it is possible to set a password/4 digit pin number
which needs to be entred to start the ebike system.
In the ‘Password’ menu, press ‘M’ to turn the password function on/off.
When the password is turned on, an old password will be requested, the
default is ‘0000’. Use ‘M’ to select each digit, and up/down to change
the value.
Then enter a new password/pin number (twice to conrm).
Press Mode to conrm the modication and go to the next setting.
the next time the bike is turned on, the password will be requested.
ASSIST SPEED-LIMIT SETTING
BATTERY
INFO
RESET
AUTO OFF
When the running speed is faster than the speed limit setting, the
controller will cut off the motor power. The speed limit default setting is
25Km/h. Press +/- to select the desired value. 99Km/h is unlimited.
Press ‘M’ to conrm the modication and go to the next setting.
The Battery menu gives a summary of the % and current Voltage of the
battery and number of charge cycles.
The Info menu gives a summary of the display information. serial
number, Firmware and Hardware versions.
This will perform a factory reset and all cutom settings will revert back
to their default setting
It is possible to adjust the system time-out which shuts down the
system after inactivity.
In ‘AutoOff’ mode, scroll up/down and select the desired Auto Off delay
between 1, 2, 3, 5, 8, 10 minutes. Default is 5 Minutes.