Coolaroo FAIRHAVEN User manual

GAZEBO
FAIRHAVEN
3.6m× 7.2m
ASSEMBLY GUIDE
5

2
3400
3400
2508
3622
2365.5
3400
7133
REF QTY REF QTY REF QTY
Carton
1/6 A4 pcs A1 2 pcs
Carton
2/6
B1 pc B1 1 pc B2 1 pc
B3 1 pc C2 pcs G2 pcs
H2 pcs I6 pcs J6 pcs
K93 pcs L2 pcs M95 pcs
N4 pcs N1 2 pcs O36 pcs
P190 pcs Q190 pcs R16 pcs
S52 pcs U1 4 pcs T1 4 pcs
W24 pcs X1 pc V2 pcs
User
Manual 1 set Y2 pcs
Carton
3/6 D12 pcs
Carton
4/6 D12 pcs
Carton
5/6 D12 pcs
Carton
6/6 D10 pcs
PARTS SUMMARY

3
REF PICTURE QTY
A4 pcs
A1 2 pcs
B1 pc
B1 1 pc
B2 1 pc
B3 1 pc
C2 pcs

4
REF PICTURE QTY
D46
pcs
G2 pcs
H2 pcs
I6 pcs
J6 pcs
K93
pcs
L2 pcs

5
REF PICTURE QTY
M95
pcs
N4
pcs
N1 2
pcs
O36
pcs
P190
pcs
Q190
pcs
R16
pcs
S52
pcs
REF PICTURE QTY
T1 4
pcs
U1 4
pcs
V2
pcs
W24
pcs
X1 pc
Y2
pcs

6
ASSEMBLY
STEP 1
Check that no parts are missing from the six boxes. Ensure you have the required
tools and safety equipment shown in gure 1.
Gloves
Tape Measure
Tape Measure
Knife
Driver
Mallet Hard Hat
Figure 1.

7
STEP 2
Slide a collar (I) over the bottom of one of the posts (A) as shown in gure 2, with
the rounded part of the collar facing towards the top of the leg. Position base plate (J)
over the bottom of the leg section and ax to the leg using 6 screws (O). Repeat this
process for the other three corner posts.
×4 times
Figure 2.

8
ASSEMBLY
STEP 3
Repeat the same process for the two centre posts.
Figure 3.
×2 times

9
Figure 4.
STEP 4
Connect the beams together (B & B1) by sliding beam B into Beam B1.
Repeat this process for beams B2 and B3 by sliding beam B3 into B2.

10
Figure 5.
STEP 5
To secure beams (B & B1) together, use spacers (T1) and screws (U1) and tighten
with Allen key ((Y). Repeat this process for beams B2 and B3.

11
STEP 6
This step requires you to join the beams and posts together whilst having all
components laying on the ground. Take Post A and place one on the le hand side
and one on the right. Place Post A1 in the centre. Slide the joined beams B & B1 into
the top of the post A1. Secure and tighten screws with Allen key (Y). Slide the ends
of the beams into the corner posts (A) and tighten screws with the Allen key (Y).
Figure 6.

12
Figure 7.
STEP 7
Take Post A and place one on the le hand side and one on the right. Place Post A1
in the centre. Slide the joined beams B2 & B3 into the top of the post A1. Secure and
tighten screws with Allen key (Y). Slide the ends of the beams into the corner posts
(A) and tighten screws with the Allen key (Y).

13
STEP 8
This step will require additional people and two ladders to help stand up each side
of the gazebo whilst installing the end beams (C). Raise both sides of the gazebo up.
Hold into position and slide in end beam (C) into the post (A) on the le and right side.
Tighten screws with Allen Key (Y).
Figure 8.

14
Figure 9.
STEP 9
Repeat the step at the other end of the gazebo. Hold into position and slide in
end beam (C) into the post (A) on the le and right side. Tighten screws with
Allen Key (Y).

15
STEP 10
Find the corner along the B bream with the crank pin hanging down.
Remove the screw from the crank pin temporarily. Slide the crank
mechanism (V) over the pin, lining up the holes. Drive the screw through
both parts. Insert the hook of the crank handle (H).
Figure 10.

16
Figure 11.
STEP 11
Take two of the louvres (D) aside. Take the louvre arm plate (L) and position it
on the inside of the le end of the louvre. Use two of the 25mm screws (Q) to ax
the controller to the louvre.
Find one of the louvre plates (K) and position it on the inside of the right end
of the louvre. Screw the plate in place using two more of the 25mm screws.
Repeat this step for the second louvre.
×2 times

17
STEP 12
Remove the crank bolt from the (B) beam using the Allen key (X). Position the louvre
at the top of the gazebo with the attached arm (L), lining up the louvre arm (L) with
the crank socket on the (B) beam, just above the crank handle (second cradle
position). Place the pin on the other end of the louvre in the second cradle position
on top of the B3 beam.
Figure 12.
Assemble the second slice to the right.

18
Figure 13.
STEP 13
Ensure the louvre arm (L) is in the correct position (as per illustration).
Re-insert the louvre bolt and tighten with the Allen key (X).

19
STEP 14
To secure the louvre pin into place, ensure the pin is sitting in the cradle on the
beam (B). Take the cover (M) and line up the holes. Once in position, screw the cover
plate in place using two M5 screws (P). Repeat this on the other side of the lovre
on beam B3.
Figure 14.

20
Figure 15.
STEP 15
This step is a repeat of step 12 but at the opposite end of the gazebo. Remove the
crank bolt from the (B1) beam using the Allen key (X). Position the louvre at the top
of the gazebo with the attached arm (L), lining up the louvre arm (L) with the crank
socket on the (B1) beam, just above the crank handle (second cradle position). Place
the louvre pin on the other end of the louvre in the second cradle position on top of
the B2 beam.
Assemble the rst slice to the le.