Coolaroo FAIRHAVEN User manual

3
ASSEMBLY GUIDE
GAZEBO
FAIRHAVEN
W
A
R
R
A
N
T
Y
W
A
R
R
A
N
T
Y
YEAR
2

T H A N K Y O U
FOR PURCHASING A
COOLAROO PRODUCT
Exposure to ultraviolet (UV) radiation from the sun is the
major cause of skin cancer. In some countries the UV radiation
is strong enough to cause sunburn in just 11 minutes on a
ne summer’s day. To prevent sun damage, we recommend
following the Sun Smart steps: slip on clothing, slop on
sunscreen, slap on a hat, slide on sunglasses and seek shade.
Attention: The illustrations in this manual are for assembly and operation
purposes only. They may dier from the gazebo’s actual appearance.
When not in use for long periods of time, dismantle the gazebo
and store in a dry place.
Components subject to turning and sliding can be treated
with a non-staining lubricant spray (silicon-based).
CARE & MAINTENANCE
To register your product, go to coolaroo.com. The product code can be found
printed above the barcode on the product packaging, alternatively you can nd
it on the relevant coolaroo.com product page.

4
PARTS SUMMARY
FAIRHAVEN
3.6m
2.5m
3.0m
REF QTY REF QTY REF QTY
BOX
1/4
A 4 pcs I 4 pcs J 4 pcs
K45 pcs L 1 pc M23 pcs
N 4 pcs O24 pcs P48 pcs
Q96 pcs R12 pcs S25 pcs
T 1 pc U 1 pc V 1 pc
W16 pcs X 1 pc Y 2 pcs
manual 1pc
BOX
2/4
B1 1pc B2 1pc C 2 pcs
G 1 pc H 1 pc
BOX
3/4 D12 pcs
BOX
4/4 D11 pcs

5

6

7
Tape Measure
Gloves
Driver Ladders
Knife Mallet Hard Hat
STEP 1
Check that no parts are missing from the four boxes. Ensure you have the required tools
and safety equipment shown in gure 1.
STEP 2
Slide a collar (I) over the bottom of one of the leg sections (A) as shown in gure 2, with the
rounded part of the collar facing towards the top of the leg. Position base plate (J) over the
bottom of the leg section and ax to the leg using 6 bolts (O). Repeat this process for the
other three legs.
A S SE MB LY

8
STEP 3
Lay two of the leg sections (A) on the ground as shown below. Take the (B1) rail and slide
each end into position in the grooves along the top of the leg sections. Use large allen key
(Y) to ax the four screws on each corner.

9
STEP 4
Lay down the other two leg sections (A) on the ground as shown. Take the (B2) rail and
slide each end into position in the grooves along the top of the leg sections, just like the
previous step. Use large allen key (Y) to ax the four screws on each corner.

10
STEP 5
Working with at least one partner and ensuring everyone is wearing a hard hat, set up two
ladders. Li up one side wall (made up of two legs and a rail) and raise one end of the beam
(C) above the opening on the leg section (A). Carefully slide the guides on the beam (C)
down into the slots on the leg section (A). Use large allen key to drive in four more screws.
A S SE MB LY

11
STEP 6
Move the ladders to the other side of the structure. Install the other beam (C) onto the
open end, using the same method as in Step 5.

12
STEP 7
Find the corner below along the B1 rail with the crank pin hanging down. Remove the
screw from the crank pin temporarily. Slide the crank loop (V) over the pin, lining up
the holes. Drive the screw through both parts. Insert the hook of the crank handle (H)
through the crank loop (V).

13
STEP 8
Take one of the louvres (D) aside and position as shown below, with the large opening
facing up and in front of you. Take the louvre arm plate (L) and position it on the inside of
the le end of the louvre. Use two of the 18mm screws (Q) to ax the controller to the
louvre.
Find one of the louvre plates (K) and position it on the inside of the right end of the louvre.
Screw the plate in place using two more of the 18mm screws.
A S SE MB LY
8

14
STEP 9
Move this louvre to the top of the structure, lining up the louvre arm (L) with the crank
socket on the B1 rail, just above the crank handle. Insert the crank bolt of the louvre arm
into the crank socket. Insert the pin on this end of the louvre into the second hole position
on top of the B1 rail. Place the pin on the other end of the louvre in the second slot position
on top of the B2 rail.

15
STEP 10
Back on the other side where the crank handle is, secure the crank bolt from the louvre
arm into the socket on the B1 rail using an M6 bolt (U) and washer (T). Tighten with the
small allen key (X).

16
STEP 11
On the other side of the louvre, secure the louvre pin into the second position slot by
placing a small cover (M) on top of the slot section, lining up the holes. Screw the cover in
place using two M5 screws (P).
A S SE MB LY

17
STEP 12
For each of the remaining 22 louvres, position a louvre plate (K) on the inside of each end.
Ax each of the plates into place using two 18mm screws (Q).
×22 times

18
STEP 13
Install one of these louvres into the rst position, next to the beam. Ensuring this louvre is
in the same orientation as the one already installed, insert the pin on the crank handle end
into the rst hole position on the B1 rail. Place the pin on the other end of the louvre into
the rst position slot. Place a small cover (M) on top and screw down in place using two
M5 screws (P).

19
STEP 14
Carefully twist the crank handle to ensure the louvre already installed in the second
position is rotating correctly (note, the louvre in the rst position is designed to remain
closed). Rotate the louvre and leave it open in a vertical position.
Install the remaining louvres in the same way as before. Ensure each louvre is in the same
orientation, insert the pin on one end of the louvre into the hole on the B1 rail, place the
other pin into the slot on the opposite end and screw down the small cover (M) with two
M5 screws (P).
A S SE MB LY

20
STEP 15
Once all louvres are correctly installed, take the louvre guide rail (G) and line up the holes
with the free louvre pins on the crank handle side. Put the louvre guide rail over the pins
as shown below. Push the straight section of a humpback pin (S) through the small hole of
each pin protruding through the guide rail.

21
STEP 16
Position an right-angle plate (N) on top of one of the corners. Use three 19mm screws (R)
to ax it into place. Repeat for the remaining corners.
STEP 17
Secure the feet of the gazebo into the ground. For a hard surface such as concrete or tile,
drill holes into the surface through the holes in the feet and install the supplied anchor
bolts (W). For other surfaces, use another suitable fastener to secure the gazebo down.
Louvres must remain open when gazebo is unattended to avoid damage during periods of
moderate to strong winds.