Outdoor Furniture Plus Vinyl Swing Arbor Firmware update

FM - 80
#VSA900
Hardware Package
16 " x 4½" Carriage Bolts
16 " Flange Nuts
8 Vinyl Hole Plugs
2⅜" NY-Glide
4 3" Scres
30 2" Screws
8 1" Screws
1 Template for Top Slats
Package contents
1Top
2 Sides
4 Braces
1 Hardware Package
4 End Caps
15 Top Slats
tools needed:
Hammer
(2) ½" Wrenches
Cordless Drill/Screwdriver
with square drive bit
Firmly tap bolts into pre-drilled
holes before tightening.
CORRECT INCORRECT 1 2 34 5
Use to measure bolts
Assembly Directions for
Vinyl Swing Arbor
To avoid personal
injury or damage to
your Arbor, assembly
requires two people.
!
40
FM-
Model # VSA900
Assembly Directions for
Vinyl Swing Arbor
Hardware Package
85⁄16" x 4½" Machine Bolts
85⁄16" x 5" Machine Bolts
32 5⁄16" Washers
16 5⁄16" Nuts
2 ⅜" NY-Glide
4 3" Screws
33
FM-
Assembly Instructions for Vinyl Swing Arbor
Model# VSA900
5" machine bolts
41/2" machine bolts
3" screws
RECOMMENDED ANCHOR METHODS
not included with units
ON WOOD DECK
Use A-23 Simpson
4 - 1" screws per post
ON CONCRETE
• A-24 bracket at each post
• 5/16" x 11/2" lag bolts
• All-American anchor
ON GROUND
S.S. Anchor through
S.S. screw eye into ground.
HARDWARE LIST:
8 - 5/16" x 4 1/2" Machine Bolts
8 - 5/16" x 5" Machine Bolts
32 - 5/16" Washers
16 - 5/16" Nuts
2 - 3/8" NY- Glide
4 - 3" Screws
3"Screws
5⁄16" x 5" Machine Bolts
5⁄16" x 4½" Machine Bolts
Assembly Directions for
Vinyl Swing Arbor
Hardware Package
85⁄16" x 4½" Machine Bolts
85⁄16" x 5" Machine Bolts
32 5⁄16" Washers
16 5⁄16" Nuts
2 ⅜" NY-Glide
4 3" Screws
33
FM-
Assembly Instructions for Vinyl Swing Arbor
Model# VSA900
5" machine bolts
41/2" machine bolts
3" screws
RECOMMENDED ANCHOR METHODS
not included with units
ON WOOD DECK
Use A-23 Simpson
4 - 1" screws per post
ON CONCRETE
• A-24 bracket at each post
• 5/16" x 11/2" lag bolts
• All-American anchor
ON GROUND
S.S. Anchor through
S.S. screw eye into ground.
HARDWARE LIST:
8 - 5/16" x 4 1/2" Machine Bolts
8 - 5/16" x 5" Machine Bolts
32 - 5/16" Washers
16 - 5/16" Nuts
2 - 3/8" NY- Glide
4 - 3" Screws
3"Screws
5⁄16" x 5" Machine Bolts
5⁄16" x 4½" Machine Bolts
12345678

Proper Care & Maintenance for
Your Fine Piece of Poly Furniture

  














Hardware Package






Package Contents




Tools Needed:





Use Simpson A-23
4 - 1" screws per post
•Simpson A-24 at each post
•⁄" x 1½" lag bolts
ON WOOD DECK ON CONCRETE ON GROUND
4 stainless steel anchors
4 lag bolts
recoMMended
ancHor
MetHods
All arbors include
your choice of
anchor option.
Side
End Cap
Top Slat
Brace
Top

FM - 81
STEP #1 - First, slide a top slat into the pre-routed hole.
Using the template provided, position the
top slat and fasten using 2" screws (see inset).
Second, fasten all the top slats.
STEP #2 - Fasten one side of the Arbor to the Top using
" x 4½" Carriage Bolts.
STEP #3 - Repeat Step #2, then set the Vinyl Swing
Arbor upright.
Top Slat
Template
Second, fasten all the top slats.
Top Slat
Template
2" Screw
STEP #2 -
⁄" x 4½ Carriage Bolts
⁄" x 4½ Carriage Bolts
⁄" x 4½ Carriage Bolts
⁄" x 4½ Carriage Bolts

FM - 82
STEP #5 - Fasten the End Caps using 2 - 1" Screws.
(One screw on each side.)
STEP #4 - Install the Vinyl Hole Plugs. (A hammer may
be needed. Tap lightly on the plug.)
STEP #6 - Fasten all 4 - Braces to the sides of the Arbor,
using " x 4½" Carriage Bolts.
STEP #7 - en use a square to ensure the Braces are
level and plumb with top. Using 3" screws,
fasten Braces to underside of Top Beam.
1" Screw
⁄" x 4½" Carriage Bolts
STEP #7 - Install the NY-Glide in the predrilled holes.
Refer to the NY-Glide installation guide for
details.