Coolworks SP15-16AZ User manual

MODEL #SP15-16AZ
16” OSCILLATING
PEDESTAL FAN
Customer Service: [email protected]
1

TECHNICAL SPECIFICATIONS
TABLE OF CONTENTS
SPECIFICATION
Voltage: 120 V AC
SPECIFICATION
Frequency: 60 Hz
Table of Contents............................................................................................................................. 2
Technical Specifications................................................................................................................... 2
Important Instructions...................................................................................................................... 3
Assembly Instructions ..................................................................................................................... 5
Operating Instructions...................................................................................................................... 6
Care and Maintenance.................................................................................................................... 7
Warranty.......................................................................................................................................... 7
IMPORTANT INSTRUCTIONS
READ & SAVE THESE INSTRUCTIONS
As with all electrical appliances, basic safety precautions should always be followed to reduce the
risk of electric shock, fire, or injury to persons, including the following precautions:
• Read all the instructions before using this fan.
• Use this fan only as described in this manual. Any other use not recommended by the
manufacturer may cause electrical shock, fire or injury to persons.
• Do not operate the fan with a damaged power cord or after the fan malfunctions or has been
dropped in any manner.
• Use of extreme caution is necessary when any fan is used by or near children, disabled
persons or pets and whenever the fan is left operating unattended.
• Do not place the fan on a small, unlevel, uneven or any surface which might allow fan to tip or
fall.
• For proper operation, fan should be placed on a smooth, non-combustible, level surface.
• Always unplug fan when not in use, when moving from place to place, when assembling or
disassembling parts, and before cleaning.
• The use of attachments, not recommended or sold by the manufacturer, may cause hazards.
• Do not use outdoors.
• Do not use fan in window. Rain may cause electrical hazard (for non-window models).
• Do not operate the fan with blade guards or any safety device removed.
• Avoid the use of extension cords due to risk of fire. If an extension cord must be used, the cord
must be minimum 14 AWG and rated not less then 1875 watts.
• Do not run power cord under carpeting. Do not cover cord with throw rugs, runners or the like.
Arrange cord away from traffic area where it will not be tripped over.
• Do not insert or allow any object to enter any openings on the fan. Doing so may cause electric
shock and/or fire hazard. Avoid contact with moving parts.
• This appliance is not intended for use by persons (including children) with reduced physical,
sensory or mental capabilities or lack of experience and knowledge, unless they have been
given supervision or instruction concerning use of the appliance by a person responsible for
their safety.
• Children should be supervised to ensure they do not play with the appliance.
2
Intended Use:
This product is intended for indoor residential and office use only, not for industrial or other
commercial applications. Use only with electrical wiring that is in good working order and that meets
applicable codes and ordinances. If you have any questions whether your wiring is adequate,
consult a qualified electrician.
While using your fan, you should follow the IMPORTANT INSTRUCTIONS listed below. As part of
those instructions, we have used the word "WARNING" to indicate the level of hazard: WARNING
indicates a hazard which, if not avoided, could result in injury or death.
3

Step 1
Pull
Chrome
Extension
Out
Step 3
Step 2
Thumb
Screw
Step 4
L
o
o
s
e
n
Step 5
Pin
Pin
Step 6 Lock-Nut Step 7
Pin Slot
Step 8
ASSEMBLY INSTRUCTIONS
(images may vary slightly from actual product)
Step 1
Unfold patented Quad-Pod®base legs.
Step 2
Place decorative Plastic Flange over Extension
Pole to cover the base. Slide pedestal pole into
base receptacle. Tighten nut to secure in place.
Slide flange over base connection.
Step 3
With collar nut loosened, pull Chrome Extension
out of Fan Pedestal.
Step 4
Assemble fan Control Panel/Motor assembly onto
Chrome Extension and tighten thumbscrew.
Step 5
Remove the Blade Cap by twisting it
CLOCKWISE while holding the metal shaft tightly.
Note: Threads are reversed.
Unscrew = Clockwise.
Step 6
Assemble Rear Grille onto Motor Housing. Rear
Grille should fit into pins on fan motor housing as
shown.
Step 7
Thread Locknut onto Motor Housing to lock Rear
Grille in place.
Step 8
Remove any protective covering over shaft before
Fan Blade Installation. Place Fan Blade onto
Motor Shaft. Notice the pin on Motor Shaft should
fit into slots of Fan Blade.
WARNING: Shock Hazard
• Use your fan only in dry environments. This fan is not intended for use in a bathroom, laundry
area, or similar locations, or near sinks, washing machines, swimming pools or other sources of
water. Never locate fan where it may fall into a bathtub or other water receptacle. Do not use in
damp environments such as flooded basements.
WARNING: Hot Surfaces
• Do not touch fan motor when in use. This motor is hot when in use; to avoid burns, do not let
bare skin touch hot surfaces.
WARNING: Fire Hazard
• Fans have arcing or sparking parts inside. Do not use near combustible materials, flammable
gases or sources of heat. DO NOT USE in areas where gasoline, paint or flammable materials
are used or stored. To prevent a possible fire, do not block air intakes or exhaust in any manner.
Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may
cause an electric shock, fire, or damage to the fan.
WARNING: Electrical Shock Hazard
• Do not use with damaged cord or plug. Use with adequate electrical circuit that is up to code.
CAUTION: to Prevent Electric Shock
• This product has a polarized two prong plug (one blade is wider than the other) that must be fully
inserted in to a matching properly grounded outlet. This plug is designed to fit a polarized outlet
only one way. If the plug does not fit fully into the outlet, reverse the plug. If the plug still does not
fit, contact a qualified electrician. Do not attempt to defeat this safety feature.
WARNING: to Reduce the Risk of Fire or Electric Shock
• Do not use this product with any solid-state speed control device.
DO NOT operate any fan with a damaged cord or plug or after fan malfunctions, has been dropped
or damaged in any manner. Do not operate fan with a broken blade, safety cage or any visual
imperfections. Disconnect power before servicing. For repairs covered under warranty, see
warranty statement. For all other repairs contact Customer Service by telephone or email for
information and assistance.
DO NOT run power cord under carpeting. DO NOT cover cord with throw rugs, runners or the like.
Arrange cord away from traffic area where it will not be tripped over. Avoid the use of extension
cords due to risk of fire. If an extension cord must be used, the cord must be minimum 14 AWG and
rated not less then 1875 watts. Do not use an extension cord unless the plug can be completely
inserted into its receptacle. Unplug the fan when not in use. Do not operate fan with its ventilation
obstructed.
54

T
i
g
h
t
e
n
Step 10
Step 9
Control Panel Oscillation Control
On/Off Speed Control Oscillation Control Knob
On/Speed Controls
Off Control
WARRANTY
Your Coolworks fan has warranty against defects in materials and workmanship for a period of
one (1) year from the date of original purchase. Please keep your proof of purchase (receipt) for
any warranty claims. Warranty does not cover wear and tear, and damages arisen from misuse
or use not in accordance with the product instructions.
Printed in China
Step 9
Thread Blade Cap onto threaded end of Motor Shaft.
Note: Threads are reversed.
Tighten = Counter-clockwise.
Step 10
With logo upright, attach Front Grille to Rear Grille by
snapping them together. Be sure all 8 clips are secure.
Usage:
Fan Operation: Always operate the fan in the upright position following all instructions and
recommendations listed in this manual.
Fan Location: Place the fan in an unobstructed area of the room that will provide proper fan cooling.
Fan Connection: Plug fan directly into 120 volt A.C., 60 Hz wall outlet. Be sure plug fits tightly in
outlet. A loose connection may cause overheating and damage to the plug or fan.
Note: To prevent overloading a circuit, do not plug the fan into a circuit that is servicing other electric
appliances.
67
OPERATING INSTRUCTIONS
CARE AND MAINTENANCE
Cleaning: CAUTION-Before cleaning the fan, be sure to disconnect power cord from the plug.
Clean the grille surface with a clean damp cloth. Do not use harsh chemical or abrasive cleaners.
DO NOT IMMERSE THE FAN OR ANY WIRES IN WATER. Replace front grille before fan use.
Allow fan to dry completely before use. Periodic grille cleaning with a vacuum will prevent dust build
up. The motor is sealed and does not require any further maintenance, cleaning or lubrication.
Maintenance: The internal motor bearings are permanently lubricated at the factory and do not
require any additional lubrication.
Repair: DO NOT OPERATE THE FAN WITHOUT THE GRILLE IN PLACE. DO NOT USE THE
FAN IF IT HAS MALFUNCTIONED OR BECOME DAMAGED IN ANY WAY.
Storage: Keep original carton for storage of the fan. Coil and tie the power cord to avoid damage
during storage.
Turning Fan On/Off: Place fan on stable level surface. Plug fan into properly grounded outlet. To
start the fan, press desired speed button: 1-LOW, 2-MED, 3-HIGH. Press 0-OFF to discontinue use.
Unplug fan when not in use.
Oscillation: To start fan oscillation, press Oscillation Control Knob (located above motor housing)
down. To stop oscillation function pull Oscillation Control Knob up while the fan is in any oscillation
position.