C A T A L O G # : T Y P E :
Specification grade 50 watt MR16
adjustable fixture rated for direct con-
tact with insulation. Remote trans-
former version is rated for 1 watt
MR16. Adjustment mechanism fea-
tures hot aiming capability, aiming
marks and tooless locking. Optics pro-
vide glare-free 50° cutoff to lamp. For
use with all halogen MR16 lamp vari-
eties.
Optical element can be changed
after installation to provide a variety of
lamp sources and distributions e g
into a wall wash
B af f l e
.040 thick aluminum spun sawtooth baffle in
matte black or white powdercoat finish.
F la ng e
Die-cast flange with either matte white or clear
coat finish
Die-cast flanges are easily removed
for field painting. Elements are keyed for proper
insertion.
A d jus t ab il it y
Removable lamp adjustment mechanism provides
up to 45° tilt and 361° rotation and locks into any
aiming position. Unit is relamped without unlock-
ing adjustments. Translating centerbeam optics
maximize light output.
L e ns
Soft focus lens standard for smooth beam
patterns. Up to two filter media can be used
which are retained during relamping.
A t tac h men t
Positive torsion springs pull flange tight to ceiling.
Mechanical light trap eliminates spill light at edge
of flange or reflector.
So c ke t
GX5.3 base for Bi-pin MR16 lamps. Back light
shield keeps interior of fixture dark.
T ra ns for me r
Truvolt
™ toroidal transformer with dual-output taps
for proper 12.0V operation. Dimmer tap compen-
sates for inherent voltage loss from dimmers,
resulting in 30% more lumens than traditional lami-
nated transformers. Toroidal design, with 90% or
greater efficiency, features a rolled one-piece con-
tinuous core of M3 grade grain oriented silicon
steel complete with an integral thermal to protect
against overheating and ensure quiet operation. For
dimming, use dimmers rated for electromagnetic
transformers.
Transformer is warranted for 5 years
and is serviceable from below ceiling
Note: If a dimming system is operated for con-
struction lighting in its “shunt” mode, i.e. bypass-
ing the dimmer modules, for an extended period of
time, fixtures with the dual-tap toroidal transformer
should be operated on the “Switched Fixture” out-
put until the dimmers are in use. Operating fixtures
on the “Dimmed Fixture” output with a full 120v
input for an extended period will overdrive the
lamp and cause shortened lamp life.
F r am e/ Ho u si n g
Hot dipped galvanized 20 gauge steel frame
with built in 1/2 inch plaster lip. Gunsights allow
for consistent alignment. Aluminum .032 thick
housing allows for heat dissipation and reduces
weight. Matte black housing interior.
Ju nc ti on B ox
18 cubic inches, listed for 4#12 AWG or 6#14
AWG 90° C additional feed through conductors,
has
six 1/2 inch pryouts.
Ba r H an gers
No Flex
® bar hangers with positive locking, for
use with wood, engineered wood and steel frame
joists spaced up to 24" O.C ship with platform.
For use in T-bar ceilings order accessory MBCLP.
Nailess barb and locator lip provide consistent
installation height.
C od es
Thermally protected, IP labeled, for use in direct
contact with insulation. Meets Washington State
Air tight requirements, 1995 CABO Model Energy
Code.
L a be l s
UL and cUL listed, standard damp label,
IBEW union made.
ADI04255
Complete unit consists of a platform and element
3 " A D JU S T A B L E
B A F F LE
For additional options please consult factory.
9"
[229mm]
10"
[254mm]
/8"
[201mm]
15 3/4"
[401mm]
3 1/2"
[89mm]
4 3/8"
[112mm]
5 1/8"
[130mm]
A cc e ss o r i es
MBCLP = 40 Push On T Bar
Clips (for 10 Units)
PLE3 = Plaster Lip Extension for
Max 2" Thick Ceiling
FMC3 = Flush Mount Collar
LSPD = Spread Lens
LLNR = Linear Spread Lens
LUV = UV Reduction Lens
LLPINK = Light Pink Lens
LLSTRAW = Light Straw Lens
L2 K = 2 00K dichroic filter
LDAY = Daylight Lens
LSPINK = Surprise Pink Lens
LPLAV = Pale Lavender Lens
LHEX = Hex Cell Louver
LSNOOT = SNOOT
F la n g e
Blank=White
die-cast
RAW=
Natural Die
Cast
Optical Ele ment
Element
E3MRAA = MR16
0 °- 45° Adjustable
Accent Baffle
P3MR = 3" Airtight
IC Rated Low Voltage
Housing
P3MR REMOTE = 3"
Airtight IC rated hous-
ing for remote trans-
former ( 1w max)
Plat f orm F in i sh
BB=Black
Baffle
WB=White
Baffle
Ceiling Cutout 4 3/8" (112mm)
Energy Data
120V Input
Lamp Input Operating
Watts Watts Current
20 23 .19
35 41 .34
3 42 .35
42 4 .39
50 5 .48
