Cooper Surgical LEEP System 1000 User manual

37864 • Rev. A • 4/13
Operating Manual (English)
Bedienungsanleitung (Deutsch / German)
Manual de funcionamiento (Español / Spanish)
Manuel d’utilisation (Français / French)
Manuale di funzionamento (Italiano / Italian)
Manual de Funcionamento (Português / Portuguese)
LEEP System 1000®Workstation, 220 VAC
Model KH1000A

English . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 1
Deutsch / German . . . . . . . . . . . . . . . . . . . . . . . . . . . . Seite 33
Español / Spanish . . . . . . . . . . . . . . . . . . . . . . . . . . . Página 65
Français / French . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 97
Italiano / Italian . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pagina 129
Português / Portuguese . . . . . . . . . . . . . . . . . . . . . . Página 161

37864 • Rev. A • 4/13
LEEP System 1000®Workstation, 220 VAC
Model KH1000A
1
Operating Manual
(English)

This page left blank intentionally
2

3
LEEP System 1000®Workstation • Model KH1000A • Operating Manual • English
LEEP System 1000®Workstation, 220 VAC
Model KH1000A
Table of Contents
Section Content Page
1. Description.............................................................................................................................. 5
1.1 Introduction .............................................................................................................................. 5
1.2 Smoke Evacuator Description .................................................................................................5
1.3 LEEP System 1000 Electrosurgical Generator Description ..................................................... 5
1.4 LEEP Cart Description ............................................................................................................. 5
2. Unpacking and Assembly...................................................................................................... 6
2.1 Unpacking the LEEP Cart (box #1) .......................................................................................... 6
2.2 Unpacking and Installing the Smoke Evacuator (box #2) ........................................................ 7
2.3 Unpacking and Installing the LEEP System 1000®Electrosurgical Generator (box #3) .......... 7
2.4 Installing the Filters and Tubing to the Smoke Evacuator ....................................................... 8
2.5 Connecting the Smoke Evacuator and LEEP System 1000®Electrosurgical Generator
together and to the Wall Outlet.................................................................................................9
2.6 Installing the Foot Pedal Switch on the LEEP System 1000 Electrosurgical Generator .......... 9
2.7 Installing the Electrodes and Dispersive Patient Plate............................................................. 9
3. LEEP System 1000®Electrosurgical Generator Features ................................................. 11
4. Front Panel of the LEEP System 1000®Electrosurgical Generator.................................. 12
5. Professional Use Guide .......................................................................................................13
5.1 LEEP Cart Use ....................................................................................................................... 13
5.2 Indications ............................................................................................................................... 14
5.3 Contraindications .................................................................................................................... 14
5.4 LEEP Procedure and Technique ............................................................................................. 14
5.5 Safety Precautions ................................................................................................................. 14
5.6 Electrosurgical Procedures ..................................................................................................... 15
5.7 Turning on the Smoke Evacuator and LEEP System 1000®Electrosurgical Generator.......... 15
6. Operating the System ........................................................................................................... 16
6.1 Setting the Controls and Output Mode.................................................................................... 16
6.2 Guidelines for Power Settings................................................................................................. 17
6.3 Thermal Effects on Tissue Treated with Loop Electrodes ....................................................... 18
7. Electrosurgical Precautions................................................................................................. 18
8. KH1000A Accessories...........................................................................................................21
9. Periodic Safety Checks and Maintenance .......................................................................... 21
9.1 LEEP System 1000®Electrosurgical Generator ...................................................................... 21
9.2 Smoke Evacuator.................................................................................................................... 21
10. Safety Circuits ....................................................................................................................... 21
11. Practical Suggestions .......................................................................................................... 22
12. Cleaning the LEEP System 1000®Electrosurgical Generator and Smoke Evacuator .... 22

4
Table of Contents (continued)
Section Content Page
13. Troubleshooting .................................................................................................................... 22
14. Accessories .......................................................................................................................... 23
15. Liability Statement ................................................................................................................ 23
16. Warranty ................................................................................................................................ 23
17. Service and Repair................................................................................................................ 24
18. LEEP System 1000®Electrosurgical Generator EMC Compliance Information .............. 25
19. Specifications........................................................................................................................ 27
19.1 Electrical – LEEP System 1000®Workstation ......................................................................... 27
19.2 General Specifications – LEEP System 1000®Electrosurgical Generator .............................. 28
19.3 Smoke Evacuator.................................................................................................................... 30
19.4 LEEP Cart ............................................................................................................................... 30
20. Explanation of Symbols........................................................................................................ 31
LEEP System 1000®Workstation • Model KH1000A • Operating Manual • English (continued)
95 Corporate Drive
Trumbull, CT 06611 USA
Phone: [phone]
Fax: [phone]
www.coopersurgical.com
International
Phone: [phone]
Fax: [phone]

5
LEEP System 1000®Workstation • Model KH1000A • Operating Manual • English (continued)
Section 1 Description
1.1 Introduction
Congratulations on owning the LEEP System 1000®Workstation, which includes the following components:
Before you can use this equipment, you must assemble the LEEP System 1000 Electrosurgical
Generator and the Smoke Evacuator onto the LEEP Cart. Refer to Section 2 for Unpacking and
Assembly instructions.
1.2 Smoke Evacuator Description
The CooperSurgical Smoke Evacuator System three-stage air filtration system is used to remove airborne
particulate plume produced during office and surgical procedures and has the following features:
– Low noise level
– Triple filtration of air provides efficiency level for 0.014 microns rated at 99.999%. This includes a
pre-filter, a charcoal filter for odor removal and a final safety filter placed after the charcoal filter
– Adjustable high air flow for effective collection of plume
– Virtually maintenance-free
– Conveniently attaches to the CooperSurgical LEEP System 1000 Workstation
1.3 LEEP System 1000 Electrosurgical Generator Description
The Electrosurgical Generator has the following features:
– Isolated power output and LED display located in the front for precise power selection, delivery
and ease of use
– Flush faceplate membrane facilitates operation and cleaning
– Microprocessor-controlled for increased precision, accuracy, reproducibility and safety
– Provides a choice of CUT, BLEND and COAG waveforms to accommodate subtle differences
in technique and electrode performance
– Pneumatic Foot Pedal for maximum safety
– Audible safety features include distinct tones for each operating setting
– Automatic self-test mechanism ensures accurate system operation
– Integrated Smoke Evacuator controls
1.4 LEEP Cart Description
Advantages of this style cart:
– Added mobility and functionality for transporting the Electrosurgical Generator and
Smoke Evacuator in one unit
– Designed to work in small exam rooms
– Heavy-duty casters ensure easy mobility
– Convenient interior storage shelves
– Elegant design for modern medical facilities
LEEP System 1000 Workstation, 220 VAC (Model KH1000A) Accessories
(filters, tubing, etc.)
LEEP System 1000®Electrosurgical Generator
220 VAC
Smoke Evacuator
220 VAC
LEEP Cart

Section 2 Unpacking and Assembly
Locate all three product boxes.
2.1 Unpacking the LEEP Cart (box #1)
When it comes to unpacking the carton that contains the Cart, great care must be taken. The box must be
on its side (following the markings on the carton for which side is up) and the Cart rolled out. Orient the box as
shown in Photo A.
CAUTION: DO NOT PICK THE CART UP OUT OF THE SHIPPING BOX BY ITS HANDLES. THE HANDLES
ARE NOT DESIGNED TO ACCOMMODATE THE FULL WEIGHT OF THE CART.
1. After removing the Cart from the shipping box, lock the front two casters.
2. Install the Smoke Evacuator next.
6
Photo A
LEEP System 1000®Workstation • Model KH1000A • Operating Manual • English (continued)

7
LEEP System 1000®Workstation • Model KH1000A • Operating Manual • English (continued)
Figure 1
2.2 Unpacking and Installing the Smoke Evacuator (box #2)
Required Tools: Phillips Screwdriver
After unpacking the Smoke Evacuator box,
1. Remove the screws on the base of the Cart in preparation for attaching the Smoke Evacuator.
2. Then align the pivot hinges on the Smoke Evacuator with the screw holes on the Cart itself and fasten
the Smoke Evacuator to the Cart. Make sure that the screws are tight, but DO NOT OVERTIGHTEN.
3. Remove the screws on the side of the Smoke Evacuator and then fasten down the bracket of the drop hinge
to the Smoke Evacuator. See Figure 1.
NOTE: The Smoke Evacuator Controls are located at the top front of the LEEP Cart for easy access.
4. Install the Electrosurgical Generator next.
2.3 Unpacking and Installing the LEEP System 1000®Electrosurgical Generator (box #3)
After unpacking the Electrosurgical Generator box, align the pins on the bottom of the Electrosurgical Generator
with the corresponding holes located on the top of the Cart. See Figure 1.
Face the Electrosurgical Generator toward the front of the Cart (where the door is) and drop the cord through the
rectangular cutout located at the top of the Cart. Do not hook up this cord until you have installed the filter and
tubing in the Smoke Evacuator.
LEEP System 1000
Electrosurgical Generator
Smoke Evacuator
Pivot Hinge
Door
LEEP Cart (A)
(B)
LEEP System 1000®Electrosurgical
Generator Control Panel
Locking Caster (wheel)
(1 of 2)
To the outlet
Insert two screws in each hinge

2.4 Installing the Filters and Tubing to the Smoke Evacuator
2.4.1 ULPA Filter Installation
Tilt the Smoke Evacuator forward and insert the large
ULPA Filter Cylinder with the air-flow arrow pointing down.
(See Photo B)
2.4.2 Installing the Pre-Filter
Insert a clean, disposable Pre-Filter onto the ULPA Filter Cylinder.
(See Photo C). Be sure this device is firmly seated.
2.4.3 Connecting the Tubing
There are two tubing hookup options:
a) For procedures requiring close-proximity plume removal (i.e., Vaginal Speculum)
b) For procedures requiring open-area plume removal (i.e., external lesions)
For procedures requiring close-proximity plume removal (i.e., Vaginal Speculum)
Assemble the ⅜" Reducer (REF 6083) onto the port on the
disposable Pre-Filter (REF 6081) top with a slight twisting
motion. Attach one end of an appropriate length of ⅜" ID
Evacuation Tubing (REF 6084) to the Reducer connector and
direct the other end to the patient and any appropriate device
being used, such as a Vaginal Speculum equipped with a
Smoke Evacuation Adapter. (See Photo D)
For procedures requiring open-area plume removal (i.e., external lesions)
Assemble the sterile, disposable 1¼" ID Evacuation Tubing (REF 6085) directly into the top of
the Pre-Filter. Position the opposite end over the site to be treated.
Photo B
Photo C
Photo D
8LEEP System 1000®Workstation • Model KH1000A • Operating Manual • English (continued)