Copystar MFD-12 User manual

0
MFD12 FLASH COPIER
User Manual
V1.10 1107
2014/10/20
COPYSTAR & BACKUP STORAGE CORPORATION
jasmine

0
Table of Contents
1. INTRODUCTION ......................................................................................................2
2. FEATURES ..............................................................................................................2
3. SPECIFICATION ......................................................................................................3
4. OPEN BOX ..............................................................................................................4
5. APPEARANCE.........................................................................................................4
5.1 MFD12 FRONT VIEW..........................................................................................4
5.2 MFD12 BACK VIEW ............................................................................................5
6. PANEL.....................................................................................................................6
6.1 DUPLICATING ....................................................................................................6
7. FUNCTION TREE.....................................................................................................7
8. MAIN FUNCTION .....................................................................................................8
8.1 BRIEF COPY ......................................................................................................8
8.2 RESIZE COPY ....................................................................................................8
8.3 DISK COPY ........................................................................................................8
8.4 VERIFY ..............................................................................................................8
8.5 ERASE...............................................................................................................9
8.6 DIAG. .................................................................................................................9
8.7 SETUP ...............................................................................................................9
9. SETUP MANUAL....................................................................................................10
9.1 SET TO DEFAULT.......................................................................................10
9.2 UPDATE FIRMWARE..................................................................................10
9.3 FORMAT UPDATE DISK..............................................................................10
9.4 SET COPY .................................................................................................10
9.5 SET COMPARE ..........................................................................................11
9.6 SET QUICK ERASE....................................................................................11
9.7 BRIEF IMMEDIATE .....................................................................................11
9.8 OPTIMIZE LOG TAB ...................................................................................12
9.9 SET DOD ERASE .......................................................................................12
9.9.1 [000]ERS DOD CYCLES ...........................................................12
9.10 SKIP READ ERROR ...................................................................................12
9.11 NO CAP CHECK.........................................................................................13
9.12 HPA CEHCK...............................................................................................13
9.13 DCO CHECK..............................................................................................13
9.14 CHECK SUM CHECK .................................................................................14
9.15 SET SMART CHECK...................................................................................14
9.16 SMART WARNING......................................................................................15

1
9.17 BTN. SOUND .............................................................................................15
9.18 SHOW EXE TIME .......................................................................................15
9.19 SHOW BINAEY BASE.................................................................................15
9.20 CMD TIME OUT..........................................................................................16
9.21 TRANS. SIZE .............................................................................................16
9.22 MAX UDMA MODE .....................................................................................16
9.23 SET WRITE PAT..........................................................................................16
9.24 DEVICE INFO.............................................................................................16
9.25 SYSTEM INFO ...........................................................................................17
9.26 TOTAL COPY COUNT.................................................................................17
9.27 BURN IN ....................................................................................................17
9.28 DIAGNOSTIC SETUP .................................................................................17
9.28.1 SET DIAG SMART....................................................................17
9.28.2 SET WRITE TEST.....................................................................17
9.27.3 SET READ TEST......................................................................18
9.27.4 SET RANDOM READ...............................................................18
9.27.5 SET RANDOM WRT.................................................................18
9.27.6 SET DIAG. PAT..........................................................................18
9.29 LANGUAGE ...............................................................................................18
9.29.1 ENGLISH....................................................................................18
9.28.2 TRADITIONAL...........................................................................19

2
1. INTRODUCTION
Congratulations on your purchase of the MFD-12 from COPYSTAR.
The MFD-12 is a high speed, stand-alone Industry Flash duplicator that can
simultaneously clone up to 12 Flash drives. The duplicator has many advanced
features for the Industry Flash Duplication, MFD-12 Supports various Flash
Memory including SATA DOM( SATA Slim) 7 pin or 22 pin, CFAST, IDE
DOM ( IDE Slim), M-SATA, M.2..
The MFD-12 Duplicator the content of a Master Flash Drive to up to 12 drives
simultaneously. With ultra fast copy speeds of up to 9GB/min, the NFD-12 is one
of the fastest cloning Flash systems available.
2. FEATURES
Up to 9GB/min transfer rates.
MFD-12 Supports various Flash Memory including SATA DOM( SATA Slim) 7 pin or
22 pin, CFAST, IDE DOM ( IDE Slim), M-SATA, M.2.(NGFF).
Simultaneously clone up to 11 Flash drives.
Supports all standard Industry Flash drives. Master & Target drives can be different
sizes, brands and models.
Various Copy&Compare Modes of Operation
(1) DISK COPY :
Used to COPY/COMPARE the whole drives with SECTOR BY SECTOR and
support ALL FILE SYSTEM & O.S. SYSTEM.
(2) BRIEF COPY :
Used to COPY/COMPARE only Data Area and skip no data area, and support Win 8,
Win 7, Win Vista, Win 2000/98/95, MAC 10.X, Ubuntu, Fedora, Red Hat,
FAT12/16/21/64, exFAT, NTFS, HFS, HPFS, EXT 1/2/3/4, XFS, GPT, LVM, UFS,

3
HPA.
(3) RESIZE COPY:
RESIZE mode is used to copy between Source and Target drives of different
capacities. The Resize mode allows for copying from a smaller capacity Source to
larger capacity Target drives. Resize copy supports the following file systems: FAT,
FAT32, NTFS.
Supports HPA(Host Protection Area) & DCO(Device Configuration Overlay) hidden
partition.
Supports very strict bit to bit data verify.
Supports completed erase functions.
Support LBA 64 bit addressing and support more than 6TB capacity at least.
Log and Graphic UI Monitoring, it supports to print & store detail operation event log
and also offers a friendly graphic user interface to monitor all copy channels status
and results.
Standalone, easy operation.
3. SPECIFICATION
Model
MFD12
Copy Channel
11
Power
200W
Weight
5kgs
Dimension
45.8X26.6X12.8(cm)
Input
8 Push Button
Display
20 X 2 TEXT LCD
Voltage
100V~240V 50/60Hz
Environment
Operation Temperature 10 ℃ ~ 35 ℃
Operation Humidity 5%~90%
Operation Temperature 41 ℉ ~122 ℉
Operation Humidity 15%~90%

4
4. OPEN BOX
If any of the following items are missing, please contact the COPYSTAR and
replacement parts will be shipping to youASAP.
MFD12 Flash Duplicator X1
AC Power Cord X1
User Manual X1
5. APPEARANCE
5.1 MFD12 FRONT VIEW

5
5.2 MFD12 BACK VIEW

6
6. PANEL
6.1 DUPLICATING
[DISK] COPY (T : 11 )
135M 6.49% 7492M
TARGETS QUANTITY
PROGRESS
WORKING SPEED
DATA SIZE
COPY FUNCTION

7
7. FUNCTION TREE
OPERATION MENU
BRIEF COPY
RESIZE COPY
DISK COPY
VERIFY
ERASE
DIAG.
SETUP MENU
SET TO DEFAULT
UPDATE FIRMWARE
FORMAT UPDATE DISK
SET COPY
SET COMPARE
SET QUICK ERASE
BRIEF IMMEDIATE
OPTIMIZE LOG TAB
SET DOD ERASE
NO CAP CHECK
HPA CHECK
DCO CHECK
CHECK SUM CHECK
SET SMART CHECK
SMART WARNING
BTN. SOUND
SHOW EXE TIME
SHOW BINAEY BASE
TRANS. SIZE
MAX UDMA MODE
SETUP
SET WRITE PAT.
DEVICE INFO
SYSTEM INFO
TOTAL COPY COUNT
BURN IN
SKIP READ ERROR
CMD TIME OUT
DIAGNOSTIC SETUP
LANGUAGE

8
8. MAIN FUNCTION
8.1 BRIEF COPY
BRIEF mode copies only the sectors that contain data and skips any blank
sectors. This mode is the fastest copy mode; it support the following system Win
8, Win 7, Win Vista, Win 2000/98/95, MAC 10.X, Ubuntu, Fedora, Red Hat,
FAT12/16/21/64, exFAT, NTFS, HFS, HPFS, EXT 1/2/3/4, XFS, GPT, LVM,
UFS, HPA. RIEF
8.2 RESIZE COPY
RESIZE mode is used to copy between Source and Target drives of different
capacities. The Resize mode allows for copying from a smaller capacity Source
to larger capacity Target drives. Resize copy supports the following file systems:
FAT, FAT32, NTFS. If the Source is not formatted as a supported file system
then the duplicator will automatically switch to FULL mode. When duplicating
in Resize mode, Target drives should all be the same capacity.
8.3 DISK COPY
DISK Copy mode copied drives sector by sector from the Source to the Targets,
and support all major OS formats and unknown file system. This DISK Copy
mode will take more time than the other copy mode; this is because it will copy
the whole sectors of the Flash. The time will be increased base on the drive’s
capacity.
8.4 VERIFY
VERIFY will check all connected flash drives and determine if they are readable.
The verification operation will check any flash drive connected to a Target port
and verifies that all sectors on the Flash are readable.

9
8.5 ERASE
ERASE deletes all information on any connected Target Flash drives by writing
zeros into each sector of the hard drive, sector by sector.
8.6 DIAG.
The Diagnostic feature allows you to run tests to verify the health of your target
flash drives.
8.7 SETUP
To enter the SETUP menu, from the Main menu press Up/Down key to select
SETUP and press ENT key.

10
9. SETUP MANUAL
9.1 SET TO DEFAULT
Restore MFD-12 to default value.
9.2 UPDATE FIRMWARE
Update MFD-12 firmware.
9.3 FORMAT UPDATE DISK
The FORMAT UPDATE DISK operation allows you to format a flash drive in
FAT 32. This flash drive can be used to store new firmware for upgrading
machine.
To format a flash drive in FAT 32
1. Connect the flash drive you want to format as a FAT32
drive to the duplicator’s source port.
2. In the SETUP menu, navigate to FORMAT UPDATE DISK and
then tap the ENT button. To format the flash drive.
3. You will receive a message asking you to confirm formatting the
flash drive. tap the ENT button or proceed or tap the ESC button to
cancel.
Once the format has completed you will receive a message confirming that the
format was successful.
9.4 SET COPY
The SET COPY option allows you to enable or disable the Copy operation. Tap
the ‘ENT’button to change this option’s setting.

11
[ ٭] –Copy enabled (default).
DISK , BRIEF or RESIZE modes will perform a Copy operation.
[ ] –Copy disabled.
FULL, BRIEF or RESIZE modes will not perform a Copy operation.
Note: To perform a Copy & Compare operation, set both the SET COPY
and SET COMPARE options.
9.5 SET COMPARE
The SET COMPARE option allows you to enable or disable the Compare
operation. Tap the ‘ENT’button to change this option’s setting.
[ ] –Compare disabled (default).
FULL, BRIEF or RESIZE modes will not perform a Compare operation.
[ ٭] –Compare enabled.
FULL, BRIEF or RESIZE modes will perform a Compare operation.
Note: To perform a Copy & Compare operation, set both the SET COPY
and SET COMPARE options.
9.6 SET QUICK ERASE
Simply erase all the data on the hard drive.
9.7 BRIEF IMMEDIATE
BRIEF IMMEDIATE is used to change the analytical method in Brief mode.
The analyze source and copy work with the same time in Brief mode.
The duplicator analyzes the source first; and then starts to copy data into the
Targets.
The default value is Disable.
For some source drives, it will take a very long time to analyze it, so enable
BRIEF IMMEDIATE is able to save more time during Brief copy.

12
9.8 OPTIMIZE LOG TAB
It allowed to optimize log table and make the copy more effective.
9.9 SET DOD ERASE
9.9.1 [000]ERS DOD CYCLES
ERASE deletes all information on any connected Target flash drives by writing
zeros and /or specific patter into each sector of the flash drive, sector by sector.
When enabled “ SET DOD ERASE”, the function name will be replaced from
ERASE to ErsDOD on the main operation manual.
9.10 SKIP READ ERROR
The SKIP READ ERROR option allows you to enable or disable error skipping
during FULL, BRIEF and RESIZE modes. Tap the ‘ENT’button to change
this option.
[ ] –Disabled (default). When an error is detected while reading from the
Source, the duplicator will cancel the current process.
[ ٭] –Enabled. When an error is detected while reading from the Source, the
duplicator will skip the bad sector on the Source and fill it with a zero on the
Target. 。
DOD ERASE, Cycle
times.
[ErsDOD] X003
[ErsDOD] 11 / [WRT0] 003
Total FLASH Devices.
DOD ERASE Steps (1) WRT:00, (2) WRT:FF, (3)
WRT:RM, (4)WRT:REVEY

13
9.11 NO CAP CHECK
The duplicator has a built in capacity check function which will check the
capacity of the Master drive and the Target drive(s) during Full or Brief copy
processes and determine whether the drives’capacities are the same.
Tap the ‘ENT’button to change this option’s setting.
[ ] –No Capacity Check is disabled (default). When a Full or Brief copy
process is executed the system will check the capacity between the Master
and Target hard drive(s) to determine whether the capacity is the same. If the
capacity is different the copy process will be cancelled.
[ ٭] –No Capacity Check is enabled. When a Full or Brief copy process is
executed the system will not check the capacity between the Master and
Target hard drive(s) and start the copy
9.12 HPA CEHCK
The Host Protected Area (HPA), sometimes referred to as the Hidden Protected
Area, is a partition on the hard drive that is not normally visible to an operating
system. Tap the ‘ENT’button to change this option’s setting.
[ ] –HPA Check is disabled (default). The system will not check for HPA
partitions.
[ ٭] –HPA Check is enabled. When HPA CHECK is enabled the duplicator
will support Host Protection Areas. When you duplicate a Master Flash that
contains HPA, the system will detect the HPA partition, unlock it, copy the area
and then re-lock the area once duplication is complete.
Note: When you view Device Info (see section ) if the drive info displays
an ‘H’ in the upper right corner then the device contains a hidden Host
Protected Area.
9.13 DCO CHECK
The Device Configuration Overlay (DCO), sometimes referred to as the Hidden
TARGET TOO SMALL !
ESC→NO, ENT→YES

14
Protected Area, is a partition on the hard drive that is not normally visible to an
operating system. Tap the ‘ENT’button to change this option’s setting.
[ ] –DCO Check is disabled (default). The system will not check for DC
partitions.
[ ٭] –DCO Check is enabled. When DCO CHECK is enabled the duplicator
will support DCO partition. When you duplicate a Master Flash that contains
DCO, the system will detect the DCO partition, unlock it, copy the area and
then re-lock the area once duplication is complete.
9.14 CHECK SUM CHECK
CHECK SUM CHECK is used to generate a CRC code between Master and
Target(s) after copy process completed.
CHECK SUM CHECK is able to work with the FULL or BRIEF copy at the same
time. It will not take extra time to do it.
If you want to check the CRC of the Source/Target(s), Hold ENT KEY one more
second and navigate UP/ DOWN to check each hard drive.
9.15 SET SMART CHECK
S.M.A.R.T.(Self Monitoring Analysis and Reporting Technology) is a monitoring
system in hard disk drives and solid-state drives that detects and reports on
various indicators of drive reliability.
S → 123456789AB
VVVVVVVVVV
SOURCE CHECK SUM :
0x19ECD646
TARGET 01 CHECK SUM
0x19ECD646
S → 123456789AB
MMMMMMMM
1th Page.
V for Successful.
X for Failed.
2th page Error Code :“M”，M
for copy successful.
Tap Up/Down key to
check all targets’ CRC.
Tap ESC back to the
previous menu.

15
If the drivers do not qualify by SMART CHECK , the drives will be rejected by
the duplicator.
9.16 SMART WARNING
The SMART WARING option allows you to configure the system check the
disk with S.M.A.R.T. function in different level [0] ,[1],[2].
That detects and reports on various indicators of drive reliability, with the intent
of enabling the anticipation of hardware failures before copy.
Level [0]: S.M.A.R.T. data indicates a possible imminent drive failure, may
only notify the user and keep going copy.
Level [1]: S.M.A.R.T. data indicates a possible imminent writing error only,
the system will reject this drive and then copy another.
Level[2]: Whatever S.M.A.R.T. data indicates any error, the system
will reject this drives.
9.17 BTN. SOUND
Disable/Enable key bee sound.
9.18 SHOW EXE TIME
The SHOW EXE TIME option allows you to enable or disable whether the total
execution time for an operation is displayed on the LCD screen. The total
execution time will be displayed after an operation has completed.
Enabled. The total execution time is displayed.
(*)Disabled (default). The total execution time is not displayed.
9.19 SHOW BINAEY BASE
Show Binary Base, it allows to show device’s capacity from Decimal to Binary.

16
The default value is Decimal.
9.20 CMD TIME OUT
CMD TIME OUT, it allows to enable Error Handling Process when happened
Read/Write error on the device. It will be according to the setting numbers to
retry the device.
9.21 TRANS. SIZE
TRANS. SIZE is allowed to change the data transfer size from 4KB to 16MB.
9.22 MAX UDMA MODE
The MAX UDMA MODE option allows you to configure the maximum transfer
speed allowed. Tap the ‘ENT’ button to change this option. The MAX UDMA M
ODE can be set as 0 –6. The MAX UDMA MODE is set to 6 by default.
9.23 SET WRITE PAT.
SET WRITE PAT. is used to define the data pattern that you want to write to all
sectors of your Target drives during an Erase operation.
The Write Pattern can be set to E5,F6,00,FF,C9,5A,A5,AA,RM(Random
Pattern).
The default value is 0x00.
9.24 DEVICE INFO
DEVICE INFO allows you to view information about any device currently
connected to the port.
MODEL
TARGET NUMBER POSITION
TRANSFER SPEC.
[2] 4011840(4/5)
CSS HSV40-002G

17
9.25 SYSTEM INFO
Display MFD-12 Version.
9.26 TOTAL COPY COUNT
TOTAL COPY COUNT keeps track of the total number of successful and
unsuccessful duplications produced by the system. This is a running count that
includes all copy modes. Tap the ‘ENT’button to view the total copy count.
9.27 BURN IN
The BURN IN function allows the system to perform a Copy, Compare, Verify,
Erase or Load function continuously to stress test for endurance, reliability and
stability.
9.28 DIAGNOSTIC SETUP
9.28.1 SET DIAG SMART
The S.M.A.R.T. (Self-Monitoring, Analysis and Reporting Technology) is a
monitoring for ATA hard drives to detect and report on various indicators of
reliability.
Enable S.M.A.R.T. feature.
Disable S.M.A.R.T. feature.
9.28.2 SET WRITE TEST
Checks the ability to write data to sectors on the target flash drives for a period
Total Pass : 00000000
Total Bad : 00000000

18
time.
9.27.3 SET READ TEST
Checks the ability to read data to sectors on the target flash drives for a period
time.
9.27.4 SET RANDOM READ
Checks the ability to random write data to sectors on the target flash drives for a
period time.
9.27.5 SET RANDOM WRT
Checks the ability to random read data from sectors on the target flash drives for
a period time.
9.27.6 SET DIAG. PAT.
SET DIAG. PAT. is used to define the data that you want to written to all sectors
of your Target flash drives during an Write Test operation. Tap the ‘ENT’
button to change this option’s setting. Tap the ‘ENT’ button to confirm your
selection again. Tap the “ESC” for escape.
9.29 LANGUAGE
9.29.1 ENGLISH
Push Up or Down button to change English or Chinese, and push ENT for
confirmation.
Push ESC to escape.