Addonics Technologies CFASTD5 User manual

Technical Support
If you need any assistance to get your unit functioning properly, please have your
product information ready and contact Addonics Technical Support at:
Hours: 8:30 am - 6:00 pm PST
Phone: [phone]
Email: http://www.addonics.com/support/query/
v8.1.11
www.addonics.com
T E C H N O L O G I E S
User Guide
1:5 CF or CFAST Duplicator
(CFASTD5 / CFD5)
ENT
ESC

www.addonics.com Technical Support (M-F 8:30am - 6:00pm PST) Phone: [phone] Email: www.addonics.com/support/query/
Diagram
ENT
ESC
ENT
ESC
Duplicator Panel
Source Slot
(CF or CFAST)
Target Slot 1
Target Slot 2 Target Slot 4
Target Slot 3
Target Slot 5
Power Switch
Power LED
Flash Reader LEDs
LCD
Scroll Up
Scroll Down
Executes Function
Cancels Function
Front View

www.addonics.com Technical Support (M-F 8:30am - 6:00pm PST) Phone: [phone] Email: www.addonics.com/support/query/
Functions
The copy controller has11 functions in total, with the 11th (Adv Setup) being a hidden system
function that only appearswhen the ESCkey ispressed for 2 seconds until there isa beep. These
are shown below.
10-01. Language
10-02. Copy Size
10-03. S tart up Menu
10-04.Auto Compare
10-05. Button Sound
10-06. Device Info
10-07. S ystemInfo
10-08. Fast Copy
10. Setup
10-09.Auto S tart Drive
10-10.Auto S tart Timer
10-11. Tolerance Size
Duplicator Controller
1. Copy HDD
2.Async Copy HDD
3. Compare HDD
4.Async Compare
5. PreScanSource
6. ReScanBUS
7. Source Size
11.Adv Setup
11-01. Read Error Skip
11-02. Update Firmware
11-03. Compare Firmware
11-04. Quick Erase HDD
11-05. Full Erase HDD
11-06. H/W Diagnostic
11-07. Load Default
8. S ecure Eras e
9. Overwrite
10-12. BootTime Delay
10-13. Quick Compare
11-08. Copy HPA
11-09. Burn In
10. Setup
11.Adv Setup

www.addonics.com Technical Support (M-F 8:30am - 6:00pm PST) Phone: [phone] Email: www.addonics.com/support/query/
Copy HDD
The LCD will show the following info during the copyin
g process: elapsed time, completed
percentage.The copy speed, capacityand time will vary
depending on the source hard disk. Once
the copying process is complete the LCD will display t
he following results.
Copy-36MB/s 0%
232.9GB 00:00:00
CopyHDD
OK: 11 Fail: 0
1. Copy HDD
HDD:11 232.9GB
Async Copy HDD
This option is used to specify the size of the source for simplifying further copying operations.
Choose option 2 from the menu:
2. Async Copy HDD
HDD:10 232.9GB
8
Space Not Enough
And then automatically copies. The LCD will display t
he following info.
Acpy-36 MB/s 0%
232.9GB 00:00:00
Async Copy HDD
OK: 11 Fail : 0
Compare
Compare HDD is used to see if the data on a source ha
rd disk is identical to the target hard disk
after the Copy HD operation.
Choose option 3 from the menu:
Copy HDD copies data directly from the source hard disk to the target hard disk. Please make
sure that the capacity of the target hard disk is equal or larger than the source hard disk.
Choose option 1 from the menu:
Press ENT to begin copy. The system will auto-detect the hard disks and show the following
copying info on the LCD.
Press ENT . Before the start of the reproduction, if the console detects that a hard drive
capacity is less than source, then the LCD will show the corresponding channel number.
If the replication process to continue to add additional hard disk device, LCD will only show the last
completed percentage.
Once the copying process is complete the LCD will display the following results.

www.addonics.com Technical Support (M-F 8:30am - 6:00pm PST) Phone: [phone] Email: www.addonics.com/support/query/
3. Compare HDD
HDD: 11 232.9GB
Press ENT to begin the comparison. The LCD will displaythe following info.
Comp-23MB/s 0%
232.9GB 00:00:00
Once thecomparison is complete the LCD will display the following info as well as the amount of
data on the source hard disk.
Compare OK:11
Fail: 0 Di
PreScan Source
PreScan HDD is used to check if the source hard disk can be accessed properly.
It alsotests the read speed.
Choose option 5 from the menu:
5. PreScan Source
HDD: 11 232.9GB
Async Compare
Compare HDD is used to seeifthe data ona sourcehard disk is identical to the
target hard disk after the Copy HDD operation. While compare process is
on-going, allows you to plug-in additional target drives and comparison will
automatically start for the added target drive.
Choose option 4 from the menu:
4. Async Compare
HDD: 11 232.9GB
Press ENT to begin the async comparison. The LCDwill display the following info.
ACmp-23MB/s 0%
232.9GB 00:00:00
Compare OK:11
Fail: 0 Di
If the comparison process continuesto add additional hard diskdevice, LCD will only show the
last completed percentage.
Once the copying process is complete the LCDwill display the following results.
Press ENTto begin scan. The LCD will display the following info
Scan-90MB/s 1%
230.6GB00:00:27
Once the scan is complete the LCD will display the corresponding results
PreScan OK!

www.addonics.com Technical Support (M-F 8:30am - 6:00pm PST) Phone: [phone] Email: www.addonics.com/support/query/
6. ReScan BUS
ReScan Bus
Choose option 6 from the menu:
Press ENT to re-scan hardware. The LCD will display the following info:
Re-Scan BUS NOW?
Yes
When the scan is complete the LCD will display the following info:
Bus re- scan OK !
7. Source Size
Source Size
Source Size is used to show the capacity of the source.
Choose option 7 from the menu:
Press ENT and the LCDwill show the following info.
HDD: Hitachi
Size: 232.9GB
Then press ENT and the LCD will showthedata's size info.
HDD: Hitachi
Data:200.9GB
8. Secure Erase
Secure Erase
Secure Erase is used to wipe the data of the hard disk, i t will erase all of HDD of duplicator
(included Source HDD).
Choose option 8 from the menu:
Press ENT to access option. By default it is set to No. Use the Up and Down arrow keys to choose
Yes.
Wipe all data.
Continue?No
Press ENT and the LCD will show the following info.
ReScan Bus allows swapping the source or target in and out without having to
reboot the system.
In Process
Elapsed 01:00

www.addonics.com Technical Support (M-F 8:30am - 6:00pm PST) Phone: [phone] Email: www.addonics.com/support/query/
10. Setup
Setup
Setup allows various system settings to be changed.There are 12 sub-options:
Language, Copy Size, Startup Menu, Auto Compare, ButtonSound, Device Info,
System Info, Fast Copy, Auto Start Drive, Auto Start Timer, Tolerance Size and
Boot Time Delay.
Choose option 8 fromthe menu:
9. Overwrite
Overwrite
Overwrite is used to overwrite the data of the hard disk, it will erase all HDDs connected to the duplicator
(including Source HDD). There are 3 sub-options: One pass, 3 pass and 7 pass.
Choose option 9 from the menu:
Press ENT to access option. By default it is One pass Use the Up and Down arrow keys to choose
other options.
9-01. Overwrite
One pass
Press ENT to access option. By default it is set to No. Use the Up and Down arrow keys to choose
Yes.
Wipe all data.
Continue?No
Press ENT and the LCD will show the following info.
In Process
Elapsed 01:00
Language
This option is used to select the system's language support. By default this is set to English. Press
ENT to change the Language settings.
Language
English

www.addonics.com Technical Support (M-F 8:30am - 6:00pm PST) Phone: [phone] Email: www.addonics.com/support/query/
10-02. Setup
CopySize
Press ENT and the LCD will display a detailed list of options as shown below
Use the Up and Down arrow keys to choose different copy sizes. The system will offer their
corresponding percentages so the user can specify the amount to copy from the source hard disk.
Press ENT to confirm and save the changes.
Copy Size
100%~1% (*MB)
Startup Menu
This option a llows you to set an option other than “Setup” to be displayed as the first available
option on the menu every time you start the system.
Startup Menu
1. Copy HDD
Press ENT then use the Up and Down arrow keys to choose other options. By default the first
menu option is Copy HDD.
10-03. Setup
Start up Menu
Auto Compare
This option automatically comparesthe source hard disk with the target hard disk after a copy
operation is completed.
Auto Compare
10-04. Setup
Auto Compare
Copy Size
This option is used to specify the size of the source hard disk for simplifying further copying
operations.
Button Sound
This option is used to control the sound of a button when you press it.
10-05. Setup
Button Sound
Press ENT and the LCD will display the following info. Use the Up and Down arrow keys to choose
whether button sound is on or 0.
Button Sound
On
Press ENT to access option. By default it is set to 0. Use the Up and Down arrow keys to choose
On.

www.addonics.com Technical Support (M-F 8:30am - 6:00pm PST) Phone: [phone] Email: www.addonics.com/support/query/
Device Info
This option is used to display the details of all hard disks connected to the copy controller.
10-06. Setup
Device Info
Press ENT and the LCD will display each hard disk' information in order as shown below.
0 Source CH: 0
Hitachi 232.9GB
System Info
This option displays system information.
10-07. Setup
System Info
Fast Copy
This option displays Fast Copy. Fast Copyonly copies data on the source drive
to the target drives. Currentlyonly supports FAT, FAT32, NTFS, HFS, Ext2 and
Ext3 partitions.
10-08. Setup
Fast Copy
Fast Copy
On
Auto Start Drive
This option is used to display to copy automatically once you insert HDD on target port.
10-09. Setup
Auto Start Drive
Auto Start Drive
Auto Start Timer
This option is used to set the period of time when the duplicator starts copying
automatically once you insert HDD on target port. Defaultis set at OFF, use the
arrows to choose time. 10-10. Setup
Auto Start Timer
Press ENT to enter the following figure. The default is 0. Use the Up and Down arrow keys to
choose 1-11.
Press ENT and the LCD will display the following info. Use the Up and Down arrow keys to choose
whether fast copy is on or 0. (This function currently only effective in FAT, FAT32, NTFS, HFS,
Ext2 and Ext3 partitions.)

www.addonics.com Technical Support (M-F 8:30am - 6:00pm PST) Phone: [phone] Email: www.addonics.com/support/query/
Auto Start Timer
Tolerance Size
10-11. Setup
Tolerance Size
Tolerance Size
1MB
BootTime Delay
This option is used to to set boot delay time.
10-12. Setup
BootTime Delay
BootTime Delay
5 sec
QuickCompare
This option is used to set the size of each comparison unit.
10-13. Setup
Quick Compare
Press ENT to enter the following figure. The default is 0. Use the Up and Down arrow keys to
choose 1 Byte/1K/10K/100K/1MB/10MB/100 Mbytes. (In order to improve the accuracy of pure
data can maintain the default settings.)
Quick Compare
Press ENT to enter the following figure. The default is 0. Use the Up and Down arrow keys to
choose 1MB~100MB of source.
This option is used to set the tolerance in terms of percentage difference between
the source and target capacity. This is to ensure that when the target drive is
smaller than the source drive, the duplication process will not start.
Press ENT to enter the following figure. The default is 0. Use the Up and Down arrow keys to
choose 5 Sec-50 Sec.
Press ENT to enter the following figure. The default is 5 sec. Use the Up and Down arrow keys to
choose 0~99 sec.