Corbin Russwin ASSA ABLOY Museo MP6600 Series User manual

FM526 03/20
Installation Instructions
For installation assistance contact Corbin Russwin
1-800-543-3658 • [e-mail]
WARNING
This product can expose you to lead
which is known to the state of California
to cause cancer and birth defects or other
reproductive harm. For more information
go to www.P65warnings.ca.gov.
Copyright © 2017, 2019, 2020 ASSA ABLOY Access and Egress Hardware Group, Inc. All rights reserved. Reproduction in
whole or in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.
MP6600 Series
Muséo®Levers
Multi-Point Lock

2
MP6600 Series
Installation Instructions
Multi-Point Lock
FM526 03/20
For installation assistance contact Corbin Russwin
1-800-543-3658 • [e-mail]
Copyright © 2017, 2019, 2020 ASSA ABLOY Access and Egress Hardware Group, Inc. All rights reserved. Reproduction in
whole or in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.
1 Tools Required
#2 and #3 Phillips Screwdrivers Flat Blade Screwdriver 1/8" Allen Wrench
TOC Table of Contents
1 Tools Required ..................................................................2
2 Package Contents ...............................................................3
3 Installation ......................................................................4
a Change Hand of Lock ............................................................4
b Change Hand of Latch ...........................................................4
c Instructions for MP6600 Series Multi-Point Lock .................................5
d Instructions for CE, RE1, and L Escutcheons .......................................6

3
MP6600 Series
Installation Instructions
Multi-Point Lock
FM526 03/20
For installation assistance contact Corbin Russwin
1-800-543-3658 • [e-mail]
Copyright © 2017, 2019, 2020 ASSA ABLOY Access and Egress Hardware Group, Inc. All rights reserved. Reproduction in
whole or in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.
2 Package Contents
Outside Lever
and Rose Assembly
Figure1
17
21
18
11
10
3
9
7
6
20
6
5
4
3
1
8
15
12
14
22
13
16
2
Figure1 Description Qty. Figure1 Description Qty.
1 Inside Lever Handle - consult factory 1 13 Emergency Button Assembly (184KB) 1
2 Handle Set Screw 1/4-28 UNF 1 14 Outside Front 1
3 Rose - LN design 2 15 Machine Screw (#12-24 x 1/2") 2
4 Machine Screw #8-32 x 5/8" 2 16 Thumb Turn Lever Assembly
(130 KB Design) -
5 Inside Adapter and Plate Assembly 2 17 KB Cylinder Rosset (for 8200) 1
6 Spindle 1 18 Compression Spring 1
7 Cap Nut 1 19 Non-loosening Wave Spring 1
8 Lever Spring 2 20 Lockbody 1
9Adapter and Plate Assembly
(LN design) 1 21 Cylinder 1
10 Mounting Post 2 22 Machine Screw (#8-32 x 1/4") 2
11 Outside Lever Handle -
consult factory 1
12 Turn Lever Assembly (130KB design) -
*All trim components vary by function number. Refer to separate instruction sheet for
trim one-side functions.

4
MP6600 Series
Installation Instructions
Multi-Point Lock
FM526 03/20
For installation assistance contact Corbin Russwin
1-800-543-3658 • [e-mail]
Copyright © 2017, 2019, 2020 ASSA ABLOY Access and Egress Hardware Group, Inc. All rights reserved. Reproduction in
whole or in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.
3 Installation
a Change Hand of Lock
Note:
Red surface of locking piece must face secure
(keyed/locked) side of door.
To rotate locking piece:
1. Position lockbody with red surface of locking
piece visible.
2. Insert blade type screwdriver into locking
piece slot to rotate locking piece.
3. Push locking piece toward back of lock body
and rotate 180° until RED surface shows on
opposite side.
Note:
Red color indicates locked side of door.
Figure2
b Change Hand of Latch
Note:
Beveled surface of latch must face strike. Deadlatch is self-adjusting.
To change hand of latch:
1. Insert flat blade screwdriver into spade
shaped slot. (Figure4)
2. Rotate screwdriver 90° to push latch out until
back of latch clears lock front; rotate latch
180°. Latch will re-enter lockbody.
Figure3
Lock Front
Latch
Figure4
Figure5
Door Handing
Inside
Outside
Left Hand
Left Hand
Reverse Bevel
Right Hand
Right Hand
Reverse Bevel
Outside
Door hands determined from outside (Secured/Keyed side)
Inside

5
MP6600 Series
Installation Instructions
Multi-Point Lock
FM526 03/20
For installation assistance contact Corbin Russwin
1-800-543-3658 • [e-mail]
Copyright © 2017, 2019, 2020 ASSA ABLOY Access and Egress Hardware Group, Inc. All rights reserved. Reproduction in
whole or in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.
3 Installation (continued)
c Instructions for MP6600 Series Multi-Point Lock
Important: Check template 4740 to prep door for
function holes, size, and location.
1. Verify strike location according to template.
2. Clean out door pocket and door edge of
any debris.
3. Make sure the handing of the lock (latch and
locking piece) match the handing of the door.
4. Slide lock into the door and hold.
5. Slide outside lever and rose assembly (or lever
and escutcheon assembly) through the door;
lock body and hold.
Note:
Keep door open while installing lock.
If installing lever onto only one side of the
door, see separate instruction sheet.
6. Assemble keyed cylinder first through narrow
end of spring and then wider opening of collar
(or escutcheon).
7. Assemble onto door by threading into lock
until cylinder face is flush with collar edge.
Pulling key slightly out of cylinder will help
when threading cylinder inward.
Note:
Corbin Russwin logo must be horizontal and
on upper portion of cylinder face.
8. Tighten cylinder clamp screw with #2 Phillips
screwdriver.
9. Secure lock in door with two (2) #12 x 1-1/4"
wood screws or #12-24 x 1/2" machine
screws. Do NOT tighten completely at this
time.
10. Slide spindle into lockbody hub.
11. Slide adapter and plate assembly over spindle
and secure with two (2) #8-32 screws.
Outside of Door
RH Door Shown
1
2
3
Figure6
4
6
8
7
5
Figure7
Outside
of Door

6
MP6600 Series
Installation Instructions
Multi-Point Lock
FM526 03/20
For installation assistance contact Corbin Russwin
1-800-543-3658 • [e-mail]
Copyright © 2017, 2019, 2020 ASSA ABLOY Access and Egress Hardware Group, Inc. All rights reserved. Reproduction in
whole or in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.
3 Installation (continued)
c Instructions for MP6600 Series Multi-Point Lock (continued)
12. Align posts in rose with holes in adapter and plate
assembly, and press on until rose is tight against
door face.
13. Attach inside lever and secure with
1/8" Allen wrench.
14. Assemble thumbturn/emergency release
(if provided) according to instructions on bag.
15. Check for proper lock operation by function
prior to closing door.
16. Tighten two lockbody screws completely.
17. Attach outside front with two (2) #8-32 x
1/4" flat head screws.
d Instructions for CE, RE1, and L Escutcheons
Through-bolt the inside escutcheon to the outside
escutcheon with two screws #8-32 x 1-7/8".
Notes:
• Screw heads should be visible on inside escutcheon.
• Removable core or interchangeable core cylinders require
a control key (a key stamped with "C") to remove and install
the inner cylinder core. This is not standard;
must be requested separately. If requesting 1-bitted control key,
specify 113511 cut.
• Cylinder collar(s) are required for functions with two (2) cylinders or
cylinders longer than # 41 (1-1/8"). (Figure9)
10
9
12
Figure8
Inside of Door
Outside of Door
Figure9

7
MP6600 Series
Installation Instructions
Multi-Point Lock
FM526 03/20
For installation assistance contact Corbin Russwin
1-800-543-3658 • [e-mail]
Copyright © 2017, 2019, 2020 ASSA ABLOY Access and Egress Hardware Group, Inc. All rights reserved. Reproduction in
whole or in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

Corbin Russwin is a brand associated with ASSA ABLOY Access and Egress Hardware Group, Inc., an ASSA ABLOY Group company.
Copyright © 2017, 2019, 2020 ASSA ABLOY Access and Egress Hardware Group, Inc. All rights reserved. Reproduction in whole or
in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.
For installation assistance contact Corbin Russwin
1-800-543-3658 • [e-mail]
Corbin Russwin, Inc.
225 Episcopal Road
Berlin, CT 06037 USA
Phone: [phone]
Fax: [phone]
www.corbinrusswin.com
FM526 03/20