Core Products VG106 User manual

Height: 736 mm
Width: 1000 mm
Depth: 500 mm
90min
DESK WITH 2 DRAWERS
REF. VG106
Thank you for choosing this furniture.
BEFORE YOU START ASSEMBLY please store the carton for 48 hours or more so the contents can acclimatise.
PLEASE RETAIN ALL PACKING UNTIL YOU HAVE COMPLETED ASSEMBLY.
Information about your furniture.
This furniture range has been carefully crafted from melamine faced manufactured board.
Each piece is manufactured to the highest standards using specialised computer controlled machinery to ensure accuracy.
Caring for your furniture.
Extreme temperature can cause slight movements in the board material so please avoid placing your furniture close to radiators or other direct sources of heat.
Please avoid exposing your furniture to continued bright sunlight as this can affect the colour.
Any fluid spills should be removed as quickly as possible.
Always lift your furniture when moving as dragging may cause damage to your furniture or flooring.
Always use place mats, coasters or tablecloths to help protect against scratches and accidentally dropped items. Always use heat resistant mats when placing hot or
cold items on to surfaces.
Do not sit or stand on your furniture.
After care.
Wipe all surfaces with a dry cloth and the occasional use of a normal household furniture polish and a household glass cleaner on glass surfaces.
Please do not use detergents or chemicals on your furniture.
After assembly remove all visible component identification stickers, these should remove easily however any remaining adhesive residue can be easily removed with
a label adhesive removal liquid available from most DIY or hardware stores.
Specialist glass care.
Glass can be marked with continual use by contact with rough surfaced objects or strong coloured fluids. In the unlikely event that the glass is damaged it must be
replaced without delay with toughened glass made to specification BS EN12150. Please consult a specialist glass retailer for this.
BATCH
NUMBER
BEFORE YOU START ASSEMBLY
Please check that you have all the
correct parts and fittings as detailed
on the assembly instructions.
We recommend that you build your
furniture on top of a soft clean cover to
ensure the unit does not get marked or
damaged during assembly.
FOR DAMAGED/REPLACEMENT PARTS
Please visit
www.coreproducts.co.uk/parts
PLEASE RETAIN THIS LEAFLET ALONG WITH YOUR DELIVERY
NOTE / RECEIPT FOR FUTURE REFERENCE.
Core Products 10/2020

ASSEMBLY HARDWARE
x35
Dowel Minifix Bolt
x33
Cover Caps
x33
Colour 1
x33
Minifix Cams
x2
Wall Fixing Kit
(Includes screws)
Page 2
ASSEMBLY PARTS MAX SUGGESTED LOADS
Screw
(50,8 mm)
x8
x9
Nail-On Glide
x2 x2
Handle
Manija
A
G
F
H
C
P
J
I
E
B
N
KM
L
O
K
N
L
M
D
O
A - x1
B - x1
C - x1
D - x1
E - x1
F - x1
G - x1
H - x1
I - x1
J - x1
K - x2
L - x2
M - x2
N - x2
O - x2
P - x1
8kg
8kg
8kg
30kg

1
2
3
12
Gently hit to adjust.
Repeat this in the
following steps.
Gently hit to adjust.
Repeat this in the
following steps.
Page 3
H
H
G

Page 4
4
5
6
Turn minifix cams to
the right to tighten.
1
G
H
J
I
Gently hit
to adjust.

7
8
9
Page 5
I
C
J
CI
J
G
H
Gently hit
to adjust.
Gently hit
4 11
to adjust.

10
11
Page 6
Slide the back panels
inside the cabinet
CI
J
G
H
P
D
D
4 11

12
Page 7
13
14
D
I
J
G
H
C
P
Gently hit
to adjust.
E
F

16
17
Page 8
15
B
E
F
B
Gently hit
to adjust.
F
E

18
19
20
CAREFULLY FLIP THE FURNITURE / !
Page 9
B
F
E
P
D
C
G
H
A
C
B
E
A
H
I
D
G
Gently hit
Gently hit
to adjust.
to adjust.

21
Page 10
22
23
x2
x2
Lx2 Kx2
K
LM
50,8 mm
K
O
Slide
M
L

24
Page 11
25
26
Nx2
K
L
N
O
K
M
L
N
O
Install handle
x2
x2
Gently hit
to adjust.

27
Page 12
After you finish the
adjustment of the cams,
cover them with the
cover caps. AAfter you finish
assembling the cabinet,
take off the adhesive
letters.
-WARNING! TIPPING HAZARD – Unanchored furniture can tip over
-WARNING: CHECK FOR HIDDEN PIPES AND CABLES BEFORE DRILLING.
-IMPORTANT: IF YOUR WALLS ARE NOT SOLID LIKE BRICK OR STONE, YOU WILL REQUIRE SPECIALIST
FITTINGS (NOT SUPPLIED)
-Pre-drill small pilot hole on the back edge of the furniture top using a 2mm drill bit. Attach the other end of the
fixing strip to the back edge of the furniture top using the 15mm screw + washer and securely tighten.
-Place fixing strip against the wall and mark position for drilling hole.
-Drill hole in your wall to a depth of 30mm using a 6mm drill bit. If the surface of your wall is soft and crumbly, we
would advise you to use a 5mm drill bit for a tighter fit.
-Insert plug into hole with end flush to the wall surface.
-Attach fixing strip to the wall using the 25mm screw + washer and securely tighten.
N
N
C
B
E
A
H
L
L
K
K
Slide the drawers
inside the cabinet