Corinex PoerNet User manual

Corinex PowerNet USB Adapter
Corinex PowerNet

m
s
t
‰
d

1
This Owner’s Manual, as well as the software described in it, is furnished under
license and may be used or copied only in accordance with the terms of the
license. The content of this manual is furnished for informational use only, it is
subject to change without notice, and it does not represent a commitment on
the part of Corinex Communications Corp.
Corinex Communications Corp. assumes no responsibility or liability for any
errors or inaccuracies that may appear in this book.
It is our policy to enhance our products as new technologies, hardware
components, software and firmware become available; therefore, the
information contained in this document is subject to change without notice.
Some features, functions, and operations described in this manual may not be
included and sold in certain countries due to government regulations or
marketing policies.
The use of the product or its features described in this document may be
restricted or regulated by law in some countries. If you are unsure which
restrictions or regulations apply, you should consult your regional Corinex office
or the authorized reseller.
Published by:
Corinex Communication Corp.
#308 1168 Hamilton Street
Vancouver, B.C., V6B 2S2
Canada
Tel: [phone]
Fax: [phone]
Corinex is a registered trademark of Corinex Communications Corp.
Microsoft, MS−DOS, MS, Windows, Windows NT are either registered trademarks
or trademarks of Microsoft Corporation in the U.S.A. and/or other countries.
All products or company names mentioned herein may be the trademarks of
their respective owners.
Copyright (c) 2001−2002 by Corinex Communications Corp.

2
Contents
1Introduction .............................................................................. 3
1.1 Overview................................................................................3
1.2 About this Manual .................................................................4
2Installation Guide...................................................................... 5
2.1 What this Package Contains...................................................5
2.2 System Requirements.............................................................5
2.3 Installing the USB Adapter software ......................................6
2.4 Testing the Setup.................................................................11
3User‘s Guide ............................................................................ 12
3.1 PowerNet Setup Tool User Guide .........................................12
3.2 Corinex PowerNet USB Adapter ...........................................15
3.3 FAQ .....................................................................................16
3.4 USB Adapter Specifications..................................................17
4Troubleshooting Guide............................................................ 19

3
1Introduction
1.1 Overview
The Corinex Powernet USB Adapter is a network interface
adapter, using the 110/120 or 220/240 V electrical wires in
premises as a medium for communications. After successful
installation, the indoor Powernet network behaves like a
traditional LAN for computers. The Corinex Powernet USB
Adapter supports up to 14 Mbps−network speed.
The product keeps network maintenance cost low and
eliminates usage barriers while there is no need for additional
wiring.
The Product is a higly integrated and requires no other external
electronic components.
1

4
1.2 About this Manual
This Owner‘s Manual is intended to provide sufficient
information to help you understand how to successfully install
Corinex Powernet USB Adapter to meet your networking needs.
With the information in this guide, you should be able to:
 Analyze your network efficiency
 Plan the configuration of Corinex Powernet USB Adapter
options
 Install and configure your Corinex Powernet USB Adapter
according to your plan
Verify and optimize your Corinex Powernet USB Adapters’
performance

5
2Installation Guide
2.1 What this Package Contains
When you receive your Corinex PowerNet USB Adapter, check to
be sure that your package contains:
• Corinex PowerNet USB Adapter
• AC cord
• USB cable
• This manual
• Installation CD
2.2 System Requirements
• IBM compatible PC with one available USB port (Not
hub)
• CD−ROM drive
• Windows 98/ME/2000/XP operating system
2

6
2.3 Installing the USB Adapter software
1. Insert the installation CD, it should automatically start. Do
not connect USB Adapter to PC before step 8! If the
installation program does not start automatically, start the
application by selecting „My Computer“, usually found on
the desktop. Navigate to the CD drive, and double click on
the drive. The following screen should be displayed:

7
2. Click on the „Install driver and Setup utility“. The following
screen should be displayed:
3. Click on the picture with description “USB Adapter” and
then click „Next“ to start installation. The following screen is
the welcome screen. Click „Next“ to continue.

8
4. The next screen will ask where Corinex PowerNet USB
Adapter Software should be installed. Click „Next“ to
continue.
5. This screen will ask where Setup should place the program’s
shortcuts. Select Start Menu Folder or simply click „Next“.

9
6. The following screen will appear to inform that Setup is
ready to begin installing Corinex PowerNet USB Adapter
Software on your computer. Click „Install“.
7. The following screen will appear to inform that the USB
driver that is about to be installed does not have a Microsoft
signature. Accept this to continue. (this screen varies a little
between versions of Windows)

10
8. The next screen is the last step in the process, it is now time
to connect your Corinex PowerNet USB Adapter. Plug the
supplied AC cord into the USB Adapter and into an AC
outlet. Plug the supplied USB cable into the USB Adapter
and to a USB port on your PC. Another screen similar to the
previous may appear. Accept this to continue.
If the driver was not automatically installed, follow the
instructions in the driver installation wizard and select
installation from c:\program files\Corinex\PowerNet USB
Adapter\USB drivers
9. The following screen appear in Windows 98/ME. Click “Yes”
to restart your system.
10. After restart (in Windows 20000/XP immediately, after step
8) will be automatically run “PowerNet Setup Tool”. Refer to

11
section 3.1 for details. This prevents anyone from
intercepting your transmitted data.
11. It is neccessary to configure network settings for your new
networking hardware. Refer to your operating system
manual for instructions to setup required parameters such
as IP adddress and subnet mask; or ask your system
administrator for required informations.
2.4 Testing the Setup
To verify that connection is working correctly, use the standard
Ping utility. (in Windows, click to menu Start−>Run, the write
command “ping IPADDRESS –t”, where IPADDRESS is IP address
of computer the USB adapter is connected to, e.g. “ping
192.168.4.1 –t”. This command will be stopped by pressing
CTRL+C).
• Ping the IP address of the computer the USB adapter is
connected to.
• Repeat the same process with the other power line
device on the network.
• If all nodes can ping themselves, try pinging another
power line device on the network. If this fails, there is a
problem with connections on the power line. Try a
different AC outlet.
• If the setup does not work, refer to the troubleshooting
guide, but first, try unplugging the powerline device and
reboot the computer as this sometimes fixes the
problem.

12
3User‘s Guide
3.1 PowerNet Setup Tool User Guide
The PowerNet Setup Tool allows the user to setup a private and
secure powerline network. Follow the steps on the screen of this
guide and your secure network will be setup correctly.
• Start the PowerNet Setup Tool from the Start menu by
selecting the Powernet folder and select 'PowerNet Setup
Tool'.
• This is the basic screen. Select right local powerline device
from a combo box. (MAC number in a combo box (in the
parenthesis) must be equal to MAC Number which is printed
on device). Click “Next”.
3

13
• Now the following screen should be displayed. This is the
screen where your network password is selected. Choose a
password between 4 and 24 characters, the password is case
sensitive so remember exactly how it was typed as it will be
needed for the next device being set up. Type your password
in the 'Network Password' box and click 'Next'. If you don’t
want to use encryption, uncheck box “Encrypt frames”.
• Click 'Next' again to program the Corinex Powernet USB
Adapter with the new encryption key. This will take a few
seconds. The next screen will look similar to the following
screen. The white box will list the MAC addresses of all other
installed powerline devices on the network that are
programmed with your chosen network password. If no
other devices have been programmed, the list will be empty.

14
• All devices on your network must be programmed with the
same network encryption key. Run this utility on all
computers with a powerline networking device attached. If
you have a powerline device that is not normally connected
to a computer, it must first be connected to a computer and
set up with a network encryption key.

15
3.2 Corinex PowerNet USB Adapter
The Corinex PowerNet USB Adapter introduces a new and
innovative solution for high speed communications, using the
electric wires within premises. This unique technology offers
users a wide range of networking options by using digital
powerline technology enabling 14 Mbps of “traffic” between
nodes within the network.
 Enables users to connect individual PC's or other devices
with Ethernet communications links into a local area
network through a 110/120V or 220/240V electric wires
(powerline) network
 Enables PC file and application sharing
 Enables peripheral and printer sharing through the
powerline network
 Enables shared broadband Internet access
 Enables sharing the bandwidth for multimedia payloads
including voice, data, audio and video
 Enables gaming competition within the reach of the electric
wires network
 Eliminates the requirement for special data cable wiring
 A real cost−effective and reliable solution for high speed
communication in any home or small office
This User‘s Guide has been prepared for Corinex Powernet USB
Adapter use in combination with PC’s or Laptop computers.

16
Example
Interconnection of two computers over the powerline by
using two Corinex PowerNet USB Adapter:
1. Install Corinex PowerNet USB Adapter on each of two
computers (see Installation Guide).
2. For connectivity enter the properties (see to user guide of
operating system) for this connection and set up IP
address manually. For example: 192.168.4.1 mask:
255.255.255.0 and another PC set up 192.168.4.2
mask: 255.255.255.0
3. You can check the connection by simple ping procedure
addressing the IP address of the secod PC.
3.3 FAQ
1. Is the Corinex Powernet USB Adapter still working if
there is an electricity blackout? And will it resume the
transmission automatically after the power come back ?
Corinex PowerNet Adapters are operational, when the
connected computers are rebooted and the power is back
on.
2. Once the electricity is on after blackout, is the Powernet
put into operation "automatically"?
Yes, as soon as the computers are running again. If there is
a problem, unplug the adapter and plug it back into the
connection slot.
3. As the transmission range of Powernet is around 200
meters, what happens what the distance is over say 400
meters?
We recommend to try the line for functionality and
performance before starting operations.
4. Is there any cross talk or interference issue when using
Corinex Powernet Adapters?
Within PC we don't see any interference with any other card
and/or system. OFDM is technology, which reduces any
influence coming from another device, that is connected to

17
the electric power network. The
Corinex adapters have also been FCC and CE approved.
5. In case the PCs at the different floors of the same
building, can they use the Powernet device for the data
transmission ? And how does it work ?
Powernet works on the same electric phase −the same
physical line. If the electric wires between the two outlets
used for communications in this case are connected with
each other and the maximum distance is about 200m, it
works fine.
6. Can we use Corinex Powernet Adapters for both
110/220V Power Network or are there two versions of
Corinex PowerNet?
We support both 110/120V and 220/240V on the same
device. There are even more line cord versions available and
delivered in different packages to reflect the outlet
requirements of the consumer.
3.4 USB Adapter Specifications
The following table lists the product specifications for the
Corinex PowerNetUSB Adapter.
Homeplug v 1.01 Certified
Windows 9x/Me/2000/XP Compatible
for PowerNet Setup Tool
IEEE 802.3
UL and/or international standards
Standard compliance
FCC and/or CE approved
Protocol TCP/IP
Port USB (v.1.0/1.1)