Cornelius Nordic CCM1530 User manual

ED/DF2XX 30” CCM1530 Nordic Style Lid Kit Installation Instructions
© 2007-2010, IMI Cornelius Inc. - 1 - Publication Number: 620204719INS
INSTALLATION INSTRUCTIONS
FOR
ED/DF300 30” CCM1530 NORDIC SS STYLE LID KIT
This Nordic style kit applies to the Cornelius 30” Wide CCM1530 Nordic Ice Maker.
!
WARNING:
Disconnect power to the unit before installing the adaptor following all lockout/tag out procedures established by the
user. Verify that all the power is off to the unit before performing any work.
Failure to comply could result in serious injury, death or damage to the equipment.
!
WARNING:
All ice baffle plates and bin stats, if included or recommended in this kit, must be installed as directed in this manual or
the equipment manufacturer’s instructions.
Failure to comply could result in serious injury, death or damage to the equipment.
!
WARNING:
All of the attachment screws and plates must be installed as directed in this manual.
Failure to comply could result in serious injury, death or damage to the equipment.
!
WARNING:
The dispenser must be secured with 3/8 X16 bolts (6) to the counter before installing the ice maker adapter kit. Refer
to the installation manual for the counter mounting template.
1. Position the ice maker adapter lid (item 1), flush with the rear of the cabinet, on the dispenser.
2. Seal the ice maker base to the adapter lid as follows:
A. Locate the ice maker two inches from the rear and flush with the sides of the lid. Run a bead of RTV
inside the perimeter of the ice maker base so that the base sets on the RTV.
B. Set the ice maker onto the lid. Note: if installing the ice maker from the front of the dispenser, use a
piece of 1” PVC pipe or larger as a “roller” to slide the ice maker over the front mounting bracket of the
manual fill cover.
C. Wipe away any excess RTV.
3. With the ice maker installed on top of the adapter lid, drill 0.147 diameter holes (#26 drill) into the dispenser cabi-
net using the slotted holes in the side flanges of the lid as templates. Be careful not to drill into the ice storage
hopper. Use of a drill stop (1/4 in.) is recommended. Secure the lid to the cabinet with (4) #10 sheet metal screws
(item 6).
Table 1: Loose Shipped Parts
Item No. Part No. Name Qty.
1620046139 Ice Maker Adapter Lid 1
2620050521 Manual Fill Cover 1
3620051215 Ice Maker Mounting Bracket 2
550904 RTV Sealant 3oz. Tube 1
6602701601 #10 X 1/2” Sheet Metal Screw 8
7620204719 I N S Installation Instructions 1
8630500109 Bin Stat 1
Release Date: October 27, 2010 www.cornelius.com Revision: B

ED/DF2XX 30” CCM1530 Nordic Style Lid Kit Installation Instructions
Publication Number: 620204719INS - 2 - © 2007-2010, IMI Cornelius Inc.
4. Drill 0.147 diameter holes into the ice maker cabinet and adapter lid using the ice maker mounting brackets (item
3) as templates. Be careful not to drill into any ice maker component (condenser, tubing, etc.). Secure the mount-
ing brackets to the ice maker and adapter lid with the #10 sheet metal screws (item 6) provided in the kit.
5. Install the wire form bracket supplied with the bin stat kit (item 4), through the 5/8” diameter hole in the bottom of
the ice maker. Wrap the eye of the wire form over the stud near the hole to the end of the wire form bracket and
wrap the tube around the end of the bracket several times, ensuring the tube is secure.
NOTE: The bin stat must not interfere with the agitator rotation or be in the path of ice falling from the
ice maker. If it interferes with the agitator or is in the path of the ice, bend the bracket out of the
way.
6. Check that the automatic agitation timer, located in the dispenser’s electrical control box, is set for automatic fill
cube ice. The control box is located behind the merchandiser. Remove the merchandiser by lifting up on the sides
to disengage the mounting “hooks” from the cabinet slots and rotate it forward.
7. Refer to the label in the control box for setting agitation times.
8. Install the manual fill cover (item 2) on the adapter lid (item 1). Insert the hinge pins into the pivot brackets on the
adapter lid with the cover open. Check that cover opens and closes correctly.
9. The unit is now ready for operation.
Figure 1. ED/DF2XX Kit
1
2
3
6
6
30.28
BASE
25.61
BASE
SEAL ICE MAKER
TO LID W/ RTV
POSTION ICE MAKER 2”
FROM REAR ADAPTER LID
USE ITEM 3 AS A GUIDE
4 PLACES
4 PLACES
3

ED/DF2XX 30” CCM1530 Nordic Style Lid Kit Installation Instructions
© 2007-2010, IMI Cornelius Inc. - 3 - Publication Number: 620204719INS
Figure 2. Bin Stat
Figure 3. Detail X
FRONT PANEL OF ICE MAKER
REMOVED FOR CLARITY
SEE DETAIL X
IN FIGURE 3
DETAIL X
SCALE 0.580
NOTE: BINSTAT MUST BE WRAPPED AROUND SUPPORT AS SHOWN.
BINSTAT COIL
SUPPORT
NOT SUPPLIED
WITH BINSTAT