Cornwell Tools CAT-332-DA User manual

CAT-332-DA 01/07/04
CAT-332-DA
3/32" PRO. 6"
RANDOM ORBITAL
PALM SANDER
• Operating Instructions
• Warning Information
• Parts Breakdown
Air Pressure . . . . . . . . . . . . . . . . .90 PSI (6.2 Bar)
Air Consumption . . . . . . . . . . . . . . . . . .16 SCFM
Pad Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6”
Maximum Speed . . . . . . . . . . . . . . . .10,000 RPM
Weight . . . . . . . . . . . . . . . . . . . . . . . . .1.85 Lbs.
Air Inlet . . . . . . . . . . . . . . . . . . . . . . . .1/4” NPT
Overall Length . . . . . . . . . . . . . . . . . . . . . . .6.1"
Rec. Hose Size . . . . . . . . . . . . . . . . . . . . . . .3/8"
Sound Level . . . . . . . . . . . . . . . . . . . . . . .81 dba
Random Orbit . . . . . . . . . . . . . . . . . . . . . .3/32"
SPECIFICATIONS
Some dust created by power
sanding, sawing, grinding, drilling,
and other construction activities
contains chemicals known to cause
cancer, birth defects or other
reproductive harm. Some examples
of these chemicals are:
• lead from lead-based paints,
• crystalline silica from bricks
and cement and other masonry
products, and
• arsenic and chromium from
chemically-treated lumber.
Your risk from these exposures
varies, depending on how often
you do this type of work. To reduce
your exposure to these chemicals:
work in a well ventilated area,
and work with approved safety
equipment, such as those dust
masks that are specially designed
to filter out microscopic particles.
CAT-332DA_op_man_010704.q 1/8/04 2:03 PM Page 1

CAT-332-DA 01/07/04
This Instruction Manual Contains Important
Safety Information.
Read THIS INSTRUCTION
MANUAL Carefully and
understand ALL INFORMATION
Before Operating THIS Tool.
• Always operate, inspect and
maintain this tool in accordance with
American National Standards Institute
Safety Code of Portable Air Tools (ANSI
B186.1) and any other applicable safety
codes and regulations.
• For safety, top performance and maximum
durability of parts, operate this tool at 90
psig 6.2 bar max air pressure with 3/8"
diameter air supply hose.
• Always wear impact-resistant
eye and face protection when
operating or performing
maintenance on this tool.
Always wear hearing protection
when using this tool.
• High sound levels can cause
permanent hearing loss. Use
hearing protection as
recommended by your employer
or OSHA regulation.
• Keep the tool in efficient operating
condition.
• Operators and maintenance personnel
must be physically able to handle the bulk,
weight and power of this tool.
• Air under pressure can cause
severe injury. Never direct air at
yourself or others. Always turn
off the air supply, drain hose of
air pressure and detach tool
from air supply before installing,
removing or adjusting any accessory on
this tool, or before performing any
maintenance on this tool. Failure to do so
could result in injury. Whip hoses can
cause serious injury. Always check for
damaged, frayed or loose hoses and
fittings, and replace immediately. Do not
use quick detach couplings at tool. See
instructions for correct set-up.
• Air powered tools can vibrate
in use. Vibration, repetitive
motions or uncomfortable
positions over extended periods
of time may be harmful to your
hands and arms. Discontinue use
of tool if discomfort, tingling feeling or pain
occurs. Seek medical advice before
resuming use.
• Place the tool on the work before starting
the tool.
• Slipping, tripping and/or falling
while operating air tools can be
a major cause of serious injury or
death. Be aware of excess hose
left on the walking or work
surface.
• Keep body working stance balanced and
firm. Do not overreach when operating the
tool.
• Anticipate and be alert for sudden changes
in motion during start up and operation of
any power tool.
• Do not carry tool by the hose.
Protect the hose from sharp
objects and heat.
• Do not lubricate tools with flammable or
volatile liquids such as kerosene, diesel or
jet fuel.
• Don't force tool beyond its rated capacity.
• Do not remove any labels. Replace any
damaged labels.
WARNING!
FAILURE TO OBSERVE THESE WARNINGS COULD RESULT IN INJURY
CAT-332DA_op_man_010704.q 1/8/04 2:03 PM Page 2

CAT-332-DA 01/07/04
CAT-332-DA
3/32" PRO. 6" RANDOM ORBITAL PALM SANDER
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
15A
16
17
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
5
1
1
Qty.
1
1
1
1
3
1
1
1
1
1
1
1
1
1
1
1
2
(Optional)
Qty.Ref. #
RSLV332
RS47502
RS47503
RS47504
RS47505
RS47506
RS47507
RS47508
RSHS332
RS47510
RS10920
RS47512
RS47513
RS47514
RS47515
RS47515A
RS47516
RS47517
Description
Lever
Pin
Muffler
Muffler Body
Inlet Bushing
Spring
Valve
Seat
Housing
Ring
Bearing
Rear End Plate
Cylinder Assy.
O-Ring
Rotor
Rotor Blade
Ring
Control
Description
O-Ring
Stem
Key
Front End Plate
Bearing
O-Ring
Lock Ring
Shaft Balancer--3/32" Orbit
Shim
Washer
Ring
Spindle
6" TE NV Vinyl Face Pad
Pad Wrench
O-Ring
Plate
Screw
Vacuum Conversion Kit
6" TE NV Hook Face Pad
6" TE Vacuum Hook Face Pad
Part #Ref. # Part #
RS47518
RS47519
RS47520
RS47521
RS227B25
RS47523
RS47524
RSSB332
RS47527
RS47529
RS47530
RS47531
CAT-6NV-PAD
RS47533
RS47534
RS47535
RS47536
CAT-4126
CAT-6NVH-PAD
CAT-6VH-PAD
18
19
20
21
22
23
24
25
27
29
30
31
32
33
34
35
36
Also available:
CAT-332DA_op_man_010704.q 1/8/04 2:03 PM Page 3

CAT-332-DA 01/07/04
Tools of this class operate on a wide range of air
pressures. It is recommended that air pressure of
these tools measures 90 PSI at the tool while
running free. Higher pressure and unclean air
will shorten tool life because of faster wear and
may create a hazardous condition.
Water in the air line will cause damage to the
tool. Drain the air tank daily. Clean the air inlet
filter screen on at least a weekly schedule. The
recommended hook-up procedure can be viewed
in Figure 1.
The air inlet (Figure 2), used for connecting air
supply, has standard 1/4" NPT American
Thread.
Line pressure should be increased to compensate
for unusually long air hoses (over 25 feet).
Minimum hose diameter should be 3/8" I.D. and
fittings should have the same inside dimensions.
AIR SUPPLY
TROUBLESHOOTING
LUBRICATION & MAINTENANCE
WARRANTY
Other factors outside the tool may cause loss of
power or erratic action. Reduced compressor
output, excessive drain on the air line, moisture
or restrictions in air pipes or the use of hose
connections of improper size or poor conditions
may reduce air supply. If outside conditions are
in order, disconnect tool from hose and take tool
to your nearest Cornwell Tools authorized service
center.
Lubricate the tool daily with a good grade of air
tool oil. If no air line oiler is used, run a
teaspoon of oil through the tool. The oil can be
squirted into the tool air inlet Figure 2, or into
the hose at the nearest connection to the air
supply, then run the tool. A rust inhibitive oil is
acceptable for air tools.
Cornwell Tools warrants its air tools for a period
of 1 year to the consumer. We will repair any air
tool covered under this warranty which proves to
be defective in material or workmanship during
the warranty period. In order to have your tool
repaired, return the tool to any Cornwell Tools
Authorized Warranty Center, freight prepaid.
Please include a copy of your proof of purchase
and a brief description of the problem. The tool
will be inspected and if any part or parts are
found to be defective in material or workman-
ship, they will be repaired free of charge and the
repaired tool will be returned to you freight
prepaid.
This warranty gives you specific rights. You may
also have other rights which vary from state to
state.
The foregoing obligation is Cornwell Tools' sole
liability under this or any implied warranty and
under no circumstances shall Cornwell Tools be
liable for any incidental or consequential
damages.
Note: Some states do not allow the exclusion or
limitation of incidental or consequential damages
so the above limitation or exclusion may not
apply to you.
Nipple
Figure 1
Figure 2
Air Inlet
CAT-332DA_op_man_010704.q 1/8/04 2:03 PM Page 4