Corsair HX1000i User manual

POWER SUPPLY
MANUAL
HIGH PERFORMANCE ATX POWER SUPPLY
ENGLISH
EN
FRANÇAIS
FR
DEUTSCH
DE
ITALIANO
IT
ESPAÑOL
ES
PORTUGUÊS
PT
POLSKI
PL

ENGLISH
TABLE OF CONTENTS
iCUE
INSTALLATION
HX1500i
HX1000i

ENGLISH
CORSAIR HXi Series fully modular power supplies deliver reliable 80 PLUS Platinum efcient power to your system.
CONGRATULATIONS ON THE PURCHASE OF YOUR NEW
CORSAIR HXi SERIES POWER SUPPLY!
SAFETY AND PROTECTION
• Over-Voltage Protection (OVP)
Over-voltage protection for the 12V, 5V, and 3.3V DC outputs is required to comply with the ATX specication.
OVP shuts down the PSU in the event that the DC outputs exceed a set level, determined by the
PSU manufacturer.
• Over-Current Protection (OCP)
OCP is featured on the 3.3V, 5V, and 12V rails. OCP ensures that the output of the DC voltage rails remains
within safe operating limits.
• Over-Temperature Protection (OTP)
OTP ensures that the PSU will shut down when the internal temperature reaches a set point. This is usually as a
result of internal current overloading or a fan failure.
• Short-Circuit Protection (SCP)
A short-circuit is dened as any output impedance of less than 0.1 ohms. Amongst other things, SCP ensures
that the PSU shuts down should the 3.3V, 5V, and 12V rails short to any other rail, or to ground. It also ensures
that no damage should occur to the unit, or your PC’s components in the event of a short.
• Over Power Protection (OPP)
Over power protection shuts off the PSU when the power drawn is between 115% and 135% of the rated power.
• Catastrophic Failure Protection
PSU must have protection circuitry to shut down safely to prevent damage from any catastrophic failures such
as ame, excessive smoke, charred PCB, fused PCB conductor, startling noise, emission of molten material, etc.
ENGLISH

1
Dimensions: 180mm(L) x 150mm(W) x 86mm(H)
Package Contents: Power Supply, AC Cable, DC Cables, Cable Ties, USB Cable, Mounting Screws, Safety Leaet
HX1000i INCLUDED HARDWARE AND SPECIFICATIONS
CORSAIR HX1000i POWER TABLE MAX LOAD MAX OUTPUT
MODEL RPS0131 +3.3V 25A
150W
PART NO. 75-004202 +5V 25A
AC INPUT RATING 100 - 240V a.c. +12V 83.3A 999.6W
INPUT CURRENT 13 - 6.5A -12V 0.3A 3.6W
FREQUENCY 47 - 63Hz +5Vsb 3.0A 15W
TOTAL POWER: 1000W
CORSAIR HX1000i POWER SUPPLY EFFICIENCY
10021050
20
95
90
85
80
75
70
input 115V a.c. input 230V a.c.EFFICIENCY (%)
SYSTEM LOAD (%)
CORSAIR HX1000i POWER SUPPLY FAN NOISE CURVE
0
1000
200 400600 800
50
40
30
20
10
0
FAN NOISE (dB)
POWER OUTPUT (W)
ENGLISH
ENGLISH

2
HX1500i INCLUDED HARDWARE AND SPECIFICATIONS
CORSAIR HX1500i POWER TABLE MAX LOAD MAX OUTPUT
MODEL RPS0132 +3.3V 25A
150W
PART NO. 75-004203 +5V 25A
AC INPUT RATING 100 - 240V a.c. +12V 125A 1500W
INPUT CURRENT 15 - 9A -12V 0.3A 3.6W
FREQUENCY 47 - 63Hz +5Vsb 3.5A 17.5W
TOTAL POWER 1500W 115V a.c. - 240V a.c.
TOTAL POWER 1200W 100V a.c. - 115V a.c.
CORSAIR HX1500i POWER SUPPLY EFFICIENCY
100
2105020
95
90
85
80
75
70
input 115V a.c. input 230V a.c.EFFICIENCY (%)
SYSTEM LOAD (%)
CORSAIR HX1500i POWER SUPPLY FAN NOISE CURVE
0
1500
300 600 900 1200
50
40
30
20
10
0
FAN NOISE (dB)
POWER OUTPUT (W)
Dimensions: 200mm(L) x 150mm(W) x 86mm(H)
Package Contents: Power Supply, AC Cable, DC Cables, Cable Ties, USB Cable, Mounting Screws, Safety Leaet
ENGLISH
ENGLISH

3
ENGLISH
DESCRIPTION QTY
CONNECTORS TOTAL LENGTH 1000W 1500W
ATX cable 24-pin (24)
610mm ± 10mm 1 1
EPS/ATX12V cable 8-pin (4+4)
650mm ± 10mm 3 3
PCIe cable 8-pin (6+2)
650mm ± 10mm 0 3
PCIe cable 8-pin (6+2)
775mm ± 10mm 3 3
SATA cable (4 SATA - straight)
800mm ± 10mm 2 2
PATA cable (4-pin)
750mm ± 10mm 2 2
USB (type C) to 10-1pin
525 mm ± 25mm 1 1
CORSAIR HXi SERIES CABLE INFORMATION
ENGLISH
610mm610mm
650mm650mm
675mm675mm
525mm525mm
650mm650mm
450mm450mm
455mm455mm 115mm115mm 115mm115mm 115mm115mm
100mm100mm 100mm100mm 100mm100mm

4
ENGLISH
STEP 1: REMOVING YOUR EXISTING PSU
Warning! To ensure proper function, only use the DC cables included with your new PSU, unless your old cables are
genuine CORSAIR cables of the same type. Please conrm your existing cables’ type before using them!
If you are building a new system, skip to Step 2:
1. Disconnect the AC power cord from your wall outlet or UPS and from the existing power supply.
2. Disconnect all the power cables from your video card, motherboard and all other peripherals.
3. Follow the directions in your chassis manual and uninstall your existing PSU.
4. Proceed to Step 2.
STEP 2: INSTALLING THE NEW POWER SUPPLY
1. Make sure the power supply’s AC power cable is not connected.
2. Follow the directions in your chassis manual and install the power supply with the screws provided.
3. Connect the 24-pin (ATX) cable to the motherboard. Connect the 8-pin +12V (EPS12V) cable to
the motherboard.
a. If your motherboard has an eight-pin +12V socket, connect the eight-pin cable directly to your motherboard.
b. If your motherboard has a four-pin socket, detach the four-pin from the eight-pin cable, and then plug this
four-pin cable directly to your motherboard.
c. Some motherboards will require a mix of 8+4 pins, use as many EPS12V cables as necessary and do not
mistake them for PCIe cables.
4. Connect the peripheral cables, PCI-Express cables, and SATA cables.
a. Connect the SATA cables to your SATA SSD or hard drive’s power sockets.
b. Connect the PCI-Express cables to the power sockets of your PCI-Express video cards if required.
c. Connect the peripheral cables to any peripherals requiring a 4-pin connector.
d. Make sure all the cables are tightly connected. Be sure to save any unused modular cables for future
component additions.
5. Connect the AC power cord to the power supply and turn it on by pushing the switch to the ON position
(marked with “I”).
INSTALLING YOUR NEW HXi SERIES POWER SUPPLY
ENGLISH

5
ENGLISH
The HXi power supply boasts a range of connectivity options for any system, users can take advantage of
CORSAIR’s robust iCUE software to monitor power settings, toggle between single to multi-rail overcurrent
protection (OCP) on-the-y, or create custom fan proles.
iCUE
ENGLISH
1. Connect the included USB-C cable to the power
supply and MB.
2. Launch iCUE, make sure it’s updated
to the latest version.
3. From Home screen, select HXi power supply
to the right.
4. Cooling - Adjust Fan Curve and create custom
Cooling Presets. Sensor tiles to the right are re-
arrangeable, simply drag and move the tile to the
desired position.
5.Alerts–Createcustomalertsprole. 6. Device Settings – Toggle between Single Rail OCP
and Multi-Rail OCP under PSU Mode.

TABLE DES MATIÈRES
FRANÇAIS
iCUE
HX1500i
HX1000i
INSTALLATION

FRANÇAIS
FRANÇAIS
SÉCURITÉ ET PROTECTION
• Protection Contre La Surtension (OVP)
La conformité à la spécication ATX requiert une protection contre la surtension au niveau des sorties CC 12V,
5V et 3,3V. Cette protection coupe l’alimentation lorsque les sorties CC dépassent un seuil établi, déterminé par
le constructeur du bloc d’alimentation.
• Protection Contre Les Surintensités (OCP)
L’OCP est intégrée sur les rails 3,3V, 5V et 12V. Cette protection garantit que la sortie en tension des rails CC
s’inscrit dans les limites d’une exploitation sûre.
• Protection Contre Les Surchauffes (OTP)
La protection contre les surchauffes (OTP) garantit que l’alimentation s’arrête lorsque sa température interne
atteint un seuil déni. Cette situation résulte généralement d’une surcharge électrique interne ou de la défaillance
du ventilateur.
• Protection Contre Les Courts-Circuits (SCP)
Un court-circuit se dénit par toute impédance de sortie inférieure à 0,1ohm. Entre autres opérations, la fonction
SCP s’assure que le bloc d’alimentation s’arrête si les rails 3,3V, 5V et 12V entrent en court-circuit les uns
avec les autres ou avec la masse. La fonction SCP garantit également qu’en cas de court-circuit, l’unité et les
composants de votre PC ne subissent aucun dommage.
• Protection Contre La Surpuissance (OPP)
La protection contre la surpuissance arrête l’alimentation lorsque la puissance prélevée est comprise entre 115%
et 135% de la puissance nominale.
• Protection Contre Les Défaillances Catastrophiques
L’alimentation doit être équipée de circuits de protection pour s’arrêter en toute sécurité an d’éviter tout
dommage dû à une défaillance catastrophique (amme, fumée excessive, circuit imprimé carbonisé, conducteur
de circuit imprimé fondu, bruit soudain, émission de matière fondue, etc.).
Les blocs d’alimentation entièrement modulaires CORSAIR HXi Series sont conçus pour délivrer une alimentation
able 80PLUS Platinum à votre système.
NOUS VOUS REMERCIONS D’AVOIR ACHETÉ LE BLOC
D’ALIMENTATION CORSAIR HXi SERIES!