Cortex GS10 User manual
GS10 Multi Station
2
TABLE OF CONTENTS
1. IMPORTANT SAFETY INSTRUCTIONS_____________________________________ 3
2. PARTS LIST_____________________________________________________________ 4
3. ASSEMBLY INSTRUCTION________________________________________________ 6
4. WARRANTY____________________________________________________________ 12
GS10 Multi Station
3
WARNING - Read all instructions before using this machine.
1. IMPORTANT SAFETY INSTRUCTIONS
Install the product on a flat level surface
Place your unit on a solid, level surface when in use
Never allow children on or near the machine.
Keep hands away from all moving parts.
Never drop or insert any object into any openings.
Care must be taken when lifting or moving the equipment so as not to injure your back. Always use
proper lifting techniques and/or seek assistance if necessary.
Keep children and pets away from the machine at all times. DO NOT leave children unattended in the
same room with the machine.
Only 1 person at a time should use the machine.
If the user experiences dizziness, nausea, chest pain, or any other abnormal symptoms, STOP the
workout at once. CONSULT A PHYSICIAN IMMEDIATELY
Do not use the machine near water or outdoors.
Keep hands away from all moving parts.
Always wear appropriate workout clothing when exercising. DO NOT wear robes or other clothing that
could become caught in the machine. Running or aerobic shoes are also required when using the
machine.
Use the machine only for its intended use as described in this manual. DO NOT use attachments not
recommended by the manufacturer.
Do not place any sharp objects around the machine.
Disabled person should not use the machine without a qualified person or physician in attendance.
Never operate the machine if the machine is not functioning properly.
A spotter is recommended during exercise.
GS10 Multi Station
4
2. PARTS LIST
GS10 Multi Station
5
GS10 Multi Station
6
3. ASSEMBLY INSTRUCTION
STEP 1
1. Attach The sliding frame (4) to Floor rack (1), using Carriage bolt M10x65 (43), Flat
washer Ф10 (35), and Lock nut M10 (36).
2. Attach Front adjusting frame (6) to Floor rack (1), using Carriage bolt M10x65 (43), Flat
washer Ф10 (35), and Lock nut M10 (36).
GS10 Multi Station
7
STEP 2
1. Attach Floor rack (1) to Rear floor rack (2) and The fixed frame (28), Using Screw M10x95
(38), Flat washer Ф10 (35) and Lock nut M10 (36).
2. Attach Left rear stand (12) to Rear floor rack (2), using Screw M10x20 (42), Flat washer
Ф10 (35) and Spring washer Ф10 (37). The same as Right rear stand (3).
3. Attach Rear adjusting frame (5) to Floor rack (1), using Screw M12x95 (46), Flat washer
Ф12 (44) and Lock nut M12 (45).
GS10 Multi Station
8
STEP 3
1. Attach Beam frame (7) to Front adjusting frame (6), Rear adjusting frame (5) and The
sliding frame (4), using Screw M12x60 (49), Flat washer Ф12 (44) and Lock nut M12
(45),Screw M12x75 (48).
2. Attach Short connection frame (9) to The sliding frame (4) and Right rear stand (3), using
Screw M12x75 (48), Flat washer Ф12 (44) and Lock nut M12 (45); Screw M10x70 (39), Flat
washer Ф10 (35), Lock nut M10 (36).
3. Attach Fixed rack (8) to Front adjusting frame (6) and Short connection frame (9), using
Screw M10x75 (40), Flat washer Ф10 (35), Lock nut M10 (36) and Pulley Φ90 (33); Screw
M12x75 (48), Flat washer Ф12 (44) and Lock nut M12 (45).
4. The same as Right rear stand (12).
GS10 Multi Station
9
STEP 4
1. Attach Long connection frame (10) to The sliding frame (4) and Fixed rack (8), Screw
M10x95 (39), Flat washer Ф10 (35), Lock nut M10 (36) and Side stiffener (29).
2. Attach Handle frame (11) to Fixed rack (8), using Screw M12x90 (47), Flat washer Ф12
(44) and Lock nut M12 (45).
3. Attach Steel cable 1 (31) to Rear sliding frame (19), using Screw M10x30 (51), Flat
washer Ф10 (35) and Lock nut M10 (36).
4. Attach Steel cable 2 (32) to Floor rack (1), using Screw M10x30 (51), Flat washer Ф10 (35)
and Lock nut M10 (36).
5. Attach Pulley frame (17) to Right sliding frame (18), using Screw M12x100 (50), Flat
washer Ф12 (44) and Lock nut M12 (45). The same as Left sliding frame (16).
6. Attach Short barbell rack (20) to Rear sliding frame (19).
7. Attach Long support frame (14) and Short support frame (15) to Front adjusting frame (6).
GS10 Multi Station
10
STEP 5
1. Attach Follow below drawing to Steel cable.
GS10 Multi Station
11
STEP 6
1. Attach Barbell rack (21) to Right rear stand (12), using Screw M10x70 (39), Flat washer
Ф10 (35) and Lock nut M10 (36). The same as Left rear stand (3).
2. Attach Limiting frame (25) to Hook frame (26), using Screw M10x75 (40), Flat washer Ф10
(35) and Lock nut M10 (36).
3. Attach Guide rod (30) to Rear adjusting frame (5) and Beam frame (7), using Screw
M10x60 (41), Screw M10x20 (42), Flat washer Ф10 (35) and Spring washer Ф10 (37).
4. Attach Long barbell rackong (24) to Liner pipe (23), using Screw M8x25 (54), Big washer
Ф8 (52), Spring washer Ф8 (53), Pipe plug Ф50 (55) and Spring wings Ф50 (57).
5. Attach Short support frame (15) to Front adjusting frame (6), using Plug (56).
GS10 Multi Station
12
4. WARRANTY
AUSTRALIAN CONSUMER LAW
Many of our products come with a guarantee or warranty from the manufacturer. In addition, they
come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled
to a replacement or refund for a major failure and compensation for any other reasonably
foreseeable loss or damage.
You are entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the
failure does not amount to a major failure. Full details of your consumer rights may be found at
www.consumerlaw.gov.au
Please visit our website to view our full warranty terms and conditions:
http://www.lifespanfitness.com.au/warranty-repairs
Warranty and Support:
For all warranty or support related enquiries an email must be sent to lodge a support case in our system.
Table of contents
Other Cortex Sport & Outdoor manuals
