Costway BC10006 User manual

Baby Playard
BC10006

Please read all instructions carefully and keep it for future reference.
General Warnings:
Attention: To prevent possible injury by entanglement, remove this toy when the child starts
trying to get up on its hands and knees in a crawling position.
Danger! Keep all small parts and packaging materials for this product away from babies and
children, otherwise they may pose a choking hazard.
The product must be installed and used under the supervision of an adult.
Read through each step carefully and follow the proper order.
Remove all Packaging, separate and count all parts and hardware before Installation.
Please ensure that all parts are correctly installed, incorrect Installation can lead to a Danger.
We recommend that, where possible, all items are assembled near to the area in which
they will be placed in use, to avoid moving the product unnecessarily once assembled.
Ensure a secure surface during construction, and place the product always on a flat, steady
and stable surface.
IMPORTANT!!!
RETAIN FOR FUTURE REFERENCE:
READ CAREFULLY.
WARNING
▲ Warning: Be aware of the risk of open fire and other sources of strong heat,
such as electric bar fires,gas fires, etc. in the near vicinity of the cot.
▲ Warning: Do not use the cot if any part is broken, torn or missing and use
only spare parts approved by the manufacturer.
▲ Warning: Do not leave anything in the cot or place the cot close to another
product,which could provide a foothold or present a danger of suffocation or
strangulation, e.g.strings, blind/curtain cords,etc.
▲ Warning: Do not use more than one mattress in the cot.
STATEMENT
This cot is ready for use,only when the locking mechanisms are engaged and to
check carefuly that they are fully engaged before using the folding cot.
If the height of the cot base is adjustable, the lowest position is the safest and
that the base should always be used in that position as soon as the baby is old
enough to sit up.
If you leave the child unattended in the cot, always make sure that the movable
side is closed,if movable sides are provided.
It is essential to remove rails before the cot is used in its lowest position if
detachable support rails are provided to support the cot base above its lowest
position.
IMPORTANT!!!
RETAIN FOR FUTURE REFERENCE:
READ CAREFULLY.
WARNING
▲ Warning: Be aware of the risk of open fire and other sources of strong heat,
such as electric bar fires,gas fires, etc. in the near vicinity of the cot.
▲ Warning: Do not use the cot if any part is broken, torn or missing and use
only spare parts approved by the manufacturer.
▲ Warning: Do not leave anything in the cot or place the cot close to another
product,which could provide a foothold or present a danger of suffocation or
strangulation, e.g.strings, blind/curtain cords,etc.
▲ Warning: Do not use more than one mattress in the cot.
STATEMENT
This cot is ready for use,only when the locking mechanisms are engaged and you
need to check carefully whether they are fully engaged before using the folding
cot.
If the height of the cot base is adjustable, the lowest position is the safest and
that the base should always be used in that position as soon as the baby is old
enough to sit up.
If you leave the child unattended in the cot, always make sure that the movable
side is closed,if movable sides are provided.
It is essential to remove rails before the cot is used in its lowest position if
detachable support rails are provided to support the cot base above its lowest
position.
02 03

TO UNFOLD:
1. Unzip the carry bag and remove the cot.(Fig.1)
2. Undo the hook&loop straps that hold the mattress around the frame.(Fig.2)
3. Remove the mattress and set it aside.
4. Now seperate the legs of the cot.(Fig.3)
5. Starting from the short rails, and pull them up quickly with both hands until
they lock into place. (Fig. 4)
6. Now do the same with the longer rails.(Fig.5)
7. Holding one end of the cot clear of the ground, gently press down on the
centre of the cot base until it lays down flat.(Fig.6)
8. Put the sheet onto the mattress(if applied)with the padded side facing up and
pass the loop straps through the gap in the sheet.
9. Place the mattress into the cot with its padded side facing up.(Fig.7)
10. Secure the mattress into the cot by passing the loop straps through the slot in
the cot base and securing it onto the book attachment, sewn onto the underside
of the cot base itself.
Thickness of the mattress shall be such that the internal height(surface of the
mattress to the upper edge of the cot frame) is at least 500mm(19.7”) in the
lowest position of the cot base and at least 200mm(7.9”) in the highest position
of the cot base.
The length and width shall be such that the gap between the mattress and the
sides and ends does not exceed 30mm.
All assembly fittings should always be tightened properly and that fittings
should be checked regularly and retightened as necessary.
To prevent fall injuries, when a child is able to climb out of the crib, the crib
should no longer be used.
TO CLEAN
Do not dry clean or use bleach.
Do not machine wash, tumble or spin dry, unless the care labelling on the
product permits these methods.
Non removable fabric covers and trims may be cleaned using a damp sponge
with soap or mild detergent, allow it to dry completely before folding or
storing it away.
In some climates the covers and trims may be affected by mould and mildew.
To help prevent this occuring. do not fold or store the product if it is damp
or wet, always store the product in a well ventilated area.
04 05

BASSINET (IF APPLIED)
TO FOLD:
1. Release the loop straps that are securing the mattress and remove the mattress
from the cot.
2. Locate the handle strap in the centre of the cot base and pull it up to upright
position(at least 50 cm (19.7”))(Fig.8)
3. Release each top rail by Ilifting the rail slightly and squeezing the bottom of
each centre joint. The buttons are covered by the top rail fabric, located at the
bottom of each rail.(Fig.9,Fig.10)
4. After ensuring that every rail is fully released, pull up on the cot base handle
strap while gathering the legs and the frame together, until the cot is completely
folded.
5. Take the mattress and wrap it around the frame.
Ensuring that straps are on the outside(Fig.11).
6. Thread the loop straps through the plastic loops,pull them tight and secure
them.(Fig.12)
7. Put the folding cot in the carry bag.(Fig.13)
Note
All the top rail should be locked into
places.
The cot base must be in a raised
position to allow the rails to lock
easily.
Ensure all four top rails are securely
engaged by press down on all rails.
NOTE
NOTE THAT IF THE TOP RAIL
DOES NOT FOLD, DO NOT FOLD
IT FORCEFULLY.
PLEASE RE-SQUEEZE THE
BUTTONS TO RELEASE THEM
COMPLETELY.
● Before installing the bassinet, make sure the 4 top rails are maintained on their
position (straight and flat).
● Take out mattress from cot and keep it within reach.
● Install the safe net on the cot.
● Make sure all hooks are tightly attached on the edge of top rails.(Fig.14)
● Install 2 pairs of support tubes, insert the tubes into the tube holder of the
safety net, then connect the tubes together. (Fig. 15)
● Place mattress onto mesh and frame.(Fig.16)
Unfold the changer and connect 2
rods. Then clamp the two plastic
hooks onto the top rails and make
sure to secure them as shown in the
picture. (Fig. 17)
CHANGER or CANOPY (IF APPLIED)
06 07

Welcome to visit our website and purchase our quality products!
We would like to extend our hearelt thanks to
all of our customers for taking me to assemble
this product and giving us valuable feedbacks.
With your inspiring rating, COSTWAY will be more consistent to offer you
EASY SHOPPING EXPERIENCE, GOOD PRODUCTS and EFFICIENT SERVICE!
US office: Fontana, California
UK office: Ipswich
Reward Points
Exclusive Customer Service
Personalized Recommendaons
Permanent Shopping Cart
Order History
08