Costway HU10039 User manual

THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE.
USER'S MANUAL
Bedside Table
HU10039

1
2
3
4
5
6
7
8
9
The product structure diagram is as follows
Preparation before Assembly
Frame Parts：
First of all, thank you very much for choosing our products. Please read
the instructions carefully before assembling. Please refer to the
certificate or packaging for the production date.
Product Introduction: The frame tube of this bedside table trolley is made of
steel pipe, the tabletop board is made of wood, and the height can be adjusted by
the upper and lower holes. The tabletop board components can be folded. The
bottom frame comes with four 2-inch plastic wheels and two brakes. The product
is suitable for the elderly, pregnant women, people with disabilities and other
people with limited mobility.
After unpacking the packing box, first remove the packing bag. Please take care
to protect all the parts in the box. If assembling on the ground, put the paper or
carpet on the ground to prevent scratches. Pay attention to the distinction
between parts and components, and then remove the inner carton, take out the
parts and place them first. (The components and hardware are shown in the
figure below.
1. Tabletop assembly
2. Inner oval tube assembly
3. Oval sleeve
4. M8 Torx Knob
5. Outer oval tube assembly
6. Chassis Assembly
7. M6 Triangle knob
8. 2” plastic castor（without
brake）
9. 2” plastic castor（with
brake）
A1. Chassis Assembly A2. Outer Oval Tube Assembly
A3. Adjustable Inner Oval Tube Assembly A4. Tabletop Assembly
A1 A2 A3 A4
02

Assembly Instructions
Please refer to the components and hardware drawings to assemble.
Step 1: As shown in Figure 1, first install two 2-inch plastic castors (with brakes)
and spring washers on the corresponding screw holes at the front end of the
chassis.
Step 2: As shown in Figure 2, install two 2-inch plastics castors(without brakes)
and spring washers on the corresponding screw holes at the rear of the chassis.
Hardware：
B1. M8 Torx knob B2. M6 Triangle knob B3. 10# Open-end wrench
B4. Hexagon socket
head screw (M6*65) B5. φ6.2 Washer B6. M6 Self-locking nut
B7. 4# Allen key B8. φ10.2 Washer B9. Steel cover
B10. Switch wrench B11. Compression
Spring
B12. 2''plastic castor
(without brake)
B13. 2''plastic castor
(with brake) B14. Spring washer B15. 14# Open-end wrench
Figure 1 Figure 2
03
B14
B14 B14
B12 B12
B13
B13
B14

Step 3: As shown in Figure 3, align the outer oval tube assembly with the
corresponding holes of the chassis assembly, take out 1 hex socket head screw
(M6*65) and 2 φ6.2 washers to connect them. Use a 4 # Allen key and a 10#
open-end wrench to lock the M6 self-locking nut.
Step 4: As shown in Figure 4, take out the M6 triangular screw, align the outer
elliptical tube assembly with the corresponding hole of the chassis assembly, and
lock it.
Step 5: As shown in Figure 5, first put the compression spring into the adjusting
inner oval tube assembly, and then insert it into the round tube of the tabletop
assembly and push it to the end.
Step 6: As shown in Figure 6, use a switch wrench to penetrate the φ10.2
washer and the iron pipe sleeve to align and adjust the inner elliptical pipe
assembly to lock the inner nut.
Figure 3 Figure 4
Figure 5 Figure 6
A2
B6
B5
B5
B4
A1 A1
B2
A2
B9
B10 B8
A3
A4
B11
04

Check after Installation
Step 7: As shown in Figure 7, the inner oval tube assembly is aligned with the
outer oval tube assembly tube, and the marble is pressed to adjust it to a suitable
height.
Step 8: As shown in Figure 8 and Figure 9, the M8 Torx knob is aligned with the
nut on the outer oval tube assembly to lock it.
1. Whether the bedside table trolley is installed correctly and whether the four
legs are flat, please refer to the manual diagram for comparison.
2. Verify that all the accessories of the bedside table trolley are fully assembled,
and you can check for extra accessories.
3. Check whether the installation of the bedside table trolley is loose.
4. Check whether all components of the bedside table trolley are skewed, and you
can make appropriate adjustments.
Product Maintenance and Maintenance Methods
1. Do not scratch or scrape the surface of the product with hard objects to
prevent material damage.
2. For daily cleaning and maintenance, apply neutral synthetic detergent, and
wipe with a damp cloth, and then wipe with a dry cloth.
3. Do not contact with strong acids and alkalis to prevent corrosion.
Storage Conditions and Methods
After packaging, the bedside table trolley should be stored at a temperature of 14
℉(-10 ℃) to 104℉(40 ℃) and a relative humidity not exceeding 80%. No
corrosive gas and well ventilated, clean room. Keep away from moisture, light
and heat during transportation.
Figure 7 Figure 8 Figure 9
A1
A2
A3
A4
B1
05

EN
DE
FR
ES
IT
PL
With your inspiring rating, COSTWAY will be more consistent to offer you EASY
SHOPPING EXPERIENCE, GOOD PRODUCTS and EFFICIENT SERVICE!
Mit Ihrer inspirierenden Bewertung wird COSTWAY konsistenter sein, um Ihnen EIN
SCHÖNES EINKAUFSERLEBNIS, GUTE PRODUKTE und EFFIZIENTEN SERVICE zu
bieten!
Avec votre évaluation inspirante, COSTWAY continuera à fournir une EXPÉRIENCE
D’ACHAT PRATIQUE, des PRODUITS DE QUALITÉ et un SERVICE EFFICACE !
Con su calificación inspiradora, COSTWAY será más consistente para ofrecerle
EXPERIENCIA DE COMPRA FÁCIL, BUENOS PRODUCTOS y SERVICIO EFICIENTE.
Con la tua valutazione incoraggiante, COSTWAY sarà più coerente per offrirti
ESPERIENZA DI ACQUISTO FACILE, BUONI PRODOTTI e SERVIZIO EFFICIENTE!
Dzięki twojej opinii COSTWAY będzie mógł oferować jeszcze WYGODNIEJSZE
ZAKUPY, LEPSZE PRODUKTY i SPRAWNIEJSZĄ OBSŁUGĘ KLIENTA.
US office: Fontana UK office: Ipswich AU office: Truganina
DE office: FDS GmbH, Neuer Höltigbaum 36, 22143 Hamburg, Deutschland
FR office: Saint Vigor d'Ymonville PL office: Gdańsk