Costway HU10196-T User manual

TWIN BED
HU10196-T
USER’S MANUAL
THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Please give us a chance to make it right and do better !
Contact our friendly customer service department for help first.
Replacements for missing or damaged parts will be shipped ASAP !
Contact Us !
Do NOT return this item. US:[e-mail]
UK:[e-mail]
AU:[email protected]
US office: Fontana UK office: Ipswich AU office: Truganina

03
Before You Start
02
Read each step carefully before starting. It is very important
to ensure each step followed in correct order, otherwise
assembly difficulties may occur.
Most of board parts are labeled or stamped on the raw
edges. Have a check to make sure all parts are included.
Work in a spacious area, preferably on a carpet close to
where the unit will be used.
Keep the handtools close at hand. Do not use power tools to
assemble your furniture. They may scratch or damage the
parts.
Ax1
Bx1 Cx2
Dx2 Ex2
Fx2 Gx2
Headboard
Footboard Headboard Leg(L&R)
Bed Roll-Out Slats Side Rail Left
Side Rail Right Side Rail Leg
PARTS LIST
HARDWARE LIST JCBC
x12
1
Flat Washer 1/4"ID x19mmOD Blk
x12
2ALLEN KEY
x1
3
ALLEN KEY
x1
4
Flat Head Chipboard Screw
x32
5
(FOR HB LEG)
M6x30mm
M4x65mm Blk
M4x32mm Rbw
(FOR SIDE RAIL)
M5x65mm Blk

04 05
STEP 1.1
Attach Head Board Leg (C) to Head Board (A) as shown using JCBC BOLT
(1) with Flat Washer (2) and securing with ALLEN KEY (3).
STEP 1.2
Fix the other holes with Screws (5) as shown.
STEP 2.1
Attach Side Rail (E) & (F) to the Side Rail Leg (G) as shown using JCBC
BOLT (1) with Flat Washer (2) and securing with ALLEN KEY (3) by
outside side rail (E) & (F).
STEP 2.2
Loosen JCBB Bolt at Headboard & Footboard Leg using Allen Key (4). (Do
not tighten them before hooking SET-UPSIDE RAIL TO HEAD BOARD (A)
closely, and push down to fit and tighten them accordingly.)
Repeat step 2.2 with other end of rail to hook onto FOOTBOARD (B).
STEP 1.1 : STEP 1.2 :
5
BACK VIEW
C C
8x
RIGHT
LEFT
C
A
3
1
2
4x
NOTE: TIGHTEN SCREWS PERIODCALLY AS SCREWS WILL
BECOME LOOSE WITH USE. CHECK TIGHTNESS OF ALL SCREW
EVERY 6-8 WEEKS.
STEP 2.1 :
A
DO NOT FULLY TIGHTEN SCREW
IN THIS STEP BEFORE ALIGNING
THE SIDE RAILS AS SHOWN.
F
E
SIDE VIEW
ALIGN BEFORE TIGHTENING
FRONT VIEW
G
R
L
Right Sticker
Left Sticker
STEP 2.2 :
8x
G
4
F
E
G
E F
G
B
E
F
3
1
2
x8
4

06 07
Care and Maintenance
Use a soft, clean cloth that will not scratch the surface when dusting.
Use of furniture polish is not necessary.
Should you choose to use polish, test first in an inconspicuous area.
Using solvents of any kind on your furniture may damage the finish.
Never use water to clean your furniture as it may cause damage to the
finish.
Liquid spills should be removed immediately. Using a soft clean cloth, blot
the spill gently. Avoid rubbing.
Check bolts/screws periodically and tighten them if necessary.
It is best to keep your furniture in a climate-controlled environment.
Extreme temperature and humidity changes can cause fading, warping,
shrinking and splitting of wood.
It is advised to keep furniture away from direct sunlight as sun may
damage the finish.
Proper care and cleaning at home will extend the life of your purchase.
Following these important and helpful tips will enhance your furniture as it
ages.
Further advice about wood
furniture care
STEP 3
Install the bed slat (D) to Side Rail (E) & (F), and tighten with Screws (5)
as shown. (NOTE: THE SETUP MUST DONE AT THE DECIDED LOCATION
FOR THE BED TO OBTAIN PERFECT STABILITY.)
Repeat Step 3 for other set of slats assembly.
Push the Side Rail (E) & (F) to meet with wooden slat (D) and fix the
Screw (5) by using the Screw Driver.
NOTE: TIGHTEN SCREWS PERIODCALLY AS SCREWS WILL
BECOME LOOSE WITH USE. CHECK TIGHTNESS OF ALL SCREW
EVERY 6-8 WEEKS.
24x
STEP 3.1 :
E
5
D