Costway HV10452 User manual

Armchair
HV10452
THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.

02
Before You Start
Please read all instructions carefully.
Retain instructions for future reference.
Separate and count all parts and hardware.
Read through each step carefully and follow the proper order.
We recommend that, where possible, all items are assembled near to the
area in which they will be placed in use, to avoid moving the product
unnecessarily once assembled.
Always place the product on a flat, steady and stable surface.
Keep all small parts and packaging materials for this product away from
babies and children as they potentially pose a serious choking hazard.

WARNING
● This product has been designed for seating one (1) average adult. To
prevent injury and damage to this unit, PROHIBIT jumping on it.
● This product is designed for home use and not intended for commercial
use.
● Children under the age of 5, small infants and babies should not sleep
alone on this product for safety reasons.
● Recommended number of people needed for handling: 2 (however it is
always better to have an extra hand.)
● THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY
INFORMATION. PLEASE READ AND KEEP FOR FUTURE
REFERENCE.
03

PARTS
SEAT BODY
x1
1
PLASTIC LEGS
x4
5
BACK REST
(In the storage underneath of seat body)
x1
2
BACK CUSHION
x1
3
ARMRESTS
x1
44
6METAL SUPPORT
x1
04

7Allen Key
x1
8Bolt
1/4"x20mm
x2
9Flat Washer
x2
10 Metal Plate
x6
11
Bolt
1/4"x35mm
x12
HARDWARES
05

Step 1: Carefully unpack parts/hardware from box and storage of
seat body, place on a clean flat surface.
HARDWARE
HARDWARE
1
METAL SUPPORT
x1
6
44
5
PLASTIC LEGS
x4
7
Allen Key
x1
8
Bolt
x2
9
Flat Washer
x2
10
Metal Plate
x6
11
Bolt
x12
1/4"x35mm
1
2
3
Storage
underneath
the seat body
06
1/4"x20mm

Step 2: Use the part (7) and (11) to assemble metal plates(10) to
the seat body.
1
11
7
11
7
Step 3: Place both armrests as shown below, then secure two legs
into pre-drilled holes on the bottom of armrests. Please avoid over
tightening.
5
5
4
5
PLASTIC LEGS
x4
07

Step 4: Carefully lift and turn assembled armrests onto its legs. Insert
metal plates of the seat body to both armrests as shown below, and
ensure it is correctly in place.
4
4
1
5
Step 5: Attach the back rest part (2) with the back cushion part (3) in
velcro area.
2
3
08

Step 7: Insert backrest metal plates to both arms as shown below,
and ensure it is correctly in place. After that, turn to the back rest and
assemble the part (6) with the hardware (7), (8), (9).
2
3
Step 6: Insert backrest with ear piece metal plates to both armrests
as shown below, and ensure it is correctly in place.
3
2
METAL SUPPORT /
SUPPORT MÉTALLIQUE
x1
6
6
6
789
09

Cover
Step 8: Finally, stretch and pull down the rear cover evenly before
securing the Velcro strip to the seat base. Repeat if necessary for better
fit.
10

11
In case a return is required, the item must be returned in original
box. Without this your return will not be accepted.
DO NOT discard the box / original packaging.
Take a photo of the box markings.
Take a photo of the damaged part (if applicable).
Send us an email with the images requested.
A photo of the markings (text) on the side of the box is required in
case a part is needed for replacement. This helps our staff identify
your product number to ensure you receive the correct parts.
A photo of the damage is always required to file a claim and get
your replacement or refund processed quickly. Please make sure
you have the box even if it is damaged.
Email us directly from marketplace where your item was purchased
with the attached images and a description of your claim.
Return / Damage Claim Instructions

If you're having difficulty, our friendly
customer team is always here to help.
USA:[email protected]
AUS:[e-mail]
GBR:[e-mail]
GBR office: FDS Corporation Limited,Unit 4, Blackacre Road, Great Blakenham,Ipswich, Ip6 0FL,United Kingdom
USA office: Fontana AUS office: Truganina