Costway HW67582 User manual

www.costway.com
THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Visit us: www.costway.com
Follow Costway
Please give us a chance to make it right and do better！
Contact our friendly customer service department for help first.
Replacements for missing or damaged parts will be shipped ASAP!
USER’S MANUAL
Electric Height Adjustable Standing Desk
HW67582

Contact Us!
Do NOT return this item.
Contact our friendly customer service department for help first.
E-mail
US: [e-mail]
UK: [e-mail]
Before You StartBefore You Start
Please read all instructions carefully.
Retain instructions for future reference.
Separate and count all parts and hardware.
Read through each step carefully and follow the proper order.
We recommend that, where possible, all items are assembled near to the
area in which they will be placed in use, to avoid moving the product
unnecessarily once assembled.
Always place the product on a flat, steady and stable surface.
Keep all small parts and packaging materials for this product away from
babies and children as they potentially pose a serious choking hazard.
www.costway.com
02

www.costway.com
IMPORTANT SAFEGUARDS
Read these instructions carefully and retain them for future use.
When using the product, basic safety precautions should always be
followed to reduce the risk of injury including the following:
● Unpack all hardware bags and components to ensure you have all the parts.
● Use the tools included to assemble the desk, don't use the incorrecct tools
to assemble.
● Do not climb, stand or sit on the desk.
● Do not place objects on the desk when moving.
● Check to ensure all bolts, screws and brackets are tightened on a regular
basis.
● Do not place the table in a humid environment.
● Do not place heavy objects on the table when storing.
● There is potential risk of personal injury not to follow the instructions when
in use.
Parts List
A B
C D
Lift column*1 Lift column*1
Base*2 Frame*2
D3
D2
D1
03

www.costway.com
Parts List
E F
G H
Side bracket*2 Motor Rod*1
IHandset + Power
supply + power cord
J
M6 screws
*40
K
M4 screws
*1
L
Tapping
screws*4
M
M10 screws
*8
N5# wrench*1
6# wrench*1
cross screwdriver*1
Desktop connection block*2
Desktop connection block*4
Desk top*4+wooden pin*12
Power supply holder*1
G1G2
G3
41
23
H *2
1H *4 2
I1Handset
I2Power supply
I3Power cord
04

www.costway.com
Assembly steps
Step 1:
1.1 Connect the board and the board with wooden pins. Then connect
and to the and tables with wooden pins.
1.2 Fasten connecting blocks H , and H , with M6 screws as shown in the
figure. M6 screws use the supplied spanner .
1.3 The hand controller is fastened to the table with self-tapping screws.
Self-tapping screws use the supplied screwdriver .
1.4 After installing the power supply holder, set aside.
Step 2:
Assemble the 2 sets of beam components as shown in the figure before use;
Note:1. Pay attention to the card slot direction.
2. The Jimmy screws at the bottom of D1 and D3 cannot be tightened.
Pay attention to the
card slot direction
1
1
2
2
J
L
3 4
N1
N3
G2
1 2
05

www.costway.com
Step 3
Fixing lift column and lift column to the table leg with M10 screws
using the supplied spanner .
Step 4:
4.1 Assembling frame tightened with M6 screws using the supplied
spanner .
4.2 Then install the two side bracket with M6 screws using the supplied
spanner .
N2
N1
N1
A B M
J
J
Prohibited removal
Pay attention to side
bracket direction
06

www.costway.com
Step 5:
5.1 Lay the table board flat and put the table shelf on it.
5.2 Attach two M6 screws on the middle crossbar, but do not tighten the
screws first. M6 screws use the supplied spanner .
5.3 Stretch the table frame to both sides. Align the screw holes and lock them
with M6 screws. Then tighten the two middles screws. M6 screws use the
supplied spanner .
5.4 Fasten the socket set screws on the middle beam.
N1
N1
J
J
Same side
Socket set
screws
07

www.costway.com
Step 6:
6.1 As shown in Figure 1, insert the hexagonal bar into the table leg B until
the buckle is not visible.
6.2 Assemble the other end of the connecting rod to the table leg A and screw
on the handle. The handle does not need to be tightened. Note: As shown in
Figure 2 below, it needs to be aligned with the card slot.
6.3 Pull the connecting rod with the handle to the bottom end of the table leg
A in the direction of the arrow as follows.
6.4 Tighten the handle and install the M4 screws.M4 screws use the
supplied screwdriver .
6.5 Connect the power cord and motor of the power supply and
handest as shown in the figure.
N3
I3I2I1
K
On the
card slot Tightened
08

www.costway.com
Operational instructions
1. Lift Column
Press the button or button to control the lift column up or down Press
the button to control up of the lifting column, you can see the height
(displayed number) on the screen; press the button to control the down of the
lifting column, you can see the height (displayed number) on the screen.
2. Set memory height
Press( ) button for 2 seconds, set the current height to the memory
height, When flashing display "H1~H4"for 2 seconds, and then display the
real-time height after 2 seconds.
3. Recall memory height
Press the number button ( ) can recall its corresponding height,
lift column will automatically run to the right position.
4. Stroke reset
"E10. E20" alarm state or running to the lowest height position, press the
button seconds, after the display ( Reset) is released, the lifting column
starts to run down to the bottom of the frame and rebound to a certain height,
the reset is completed to display the lowest height.
09

www.costway.com
5. Protection and alarm
5.1) Block Protection: Display "E02" . During the movement, a vibrating,
colliding or tilting desktop will sound an alarm and stop the movement
immediately. After the automatic release, it will move in the reverse direction
to set the distance, you can press any key to stop and release during the
reverse operation. Check and make sure that the desktop will not vibrate
significantly, hit obstacles or re-tilt during operation.
5.2) Overheating protection: Display "Hot." Continuous operating may
initiate this protection and should be recharged or waited for at least 18
minutes before use.
5.3) Motor abnormal protection: Display "E10." Should be powered off,
recheck and ensure that the connection of the motor to the controller is
reliiable and then reconnect.
5.4) Overload protection: Display "E20." This alarm should be removed from
the desk top when it’s operating up; if this alarm occurs when it’s operating
down, cut off the power and the heavy objects should be removed, and the
power should be re-charged.
5.5) Under-voltage protection: Display "E31." Should be powered off,
recheck and make sure the connection between the power supply and the
handset is reliable, then connect the power.
5.6) Over-voltage protection: Display "E32." Should be powered off, recheck
and make sure the connection between the power supply and the handset is
reliable, then connect the power.
10