Costway NP10464FR-BK User manual

THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE.
EN FR
USER'S MANUAL/MANUEL DE L'UTILISATEUR
NP10464FR-BK
Fire Pit / Foyer Extérieur
US office: Fontana UK office: Ipswich AU office: Truganina
DE office: FDS GmbH, Neuer Höltigbaum 36, 22143 Hamburg, Deutschland
FR office: Saint Vigor d'Ymonville PL office: Gdańsk

ASSEMBLY INSTRUCTION AND SAFETY GUIDE
manufacturers
Appliance name Fire Pit
16.5 kW
Model No F210020-B2
Heat input
Gas category I3+(28-30/37)
G30/G31 G30/G31 G30/G31 G30/G31
30 mbar 37 mbar
PL AT, CH, CZ,
DE, LU, SK
50 mbar
I3B/P(30) I3B/P(37) I3B/P(50)
Types of gas
Gas passure
Country of
Destination
Burner injector
FR
PIN NO. : 1936DL1587
2.05 mm
G30: 1199 g/h ; G31: 1178 g/h
1.94 mm 1.80 mm
1336/22
EN
This manual is
for：
Gas
consumption
(g/h)
BE, CH, CY,
CZ, ES, FR,
GB, GR, IE,
IT, LT, LU,
LV, PT, SI,
SK, TR
butane:28-3
0 mbar
propane:37
mbar
BE, BG, CY, CZ,
DK, EE, FI, FR,
GB, GR, HR, HU,
IT, LT, LU, LV, MT,
NL, NO, RO, SE,
SI, SK, TR
● Close the valve of the gas cylinder or the regulator after use.
● Read the instructions before using this appliance.
● For use outdoors and in well ventilated areas.
● The use of this appliance in enclosed areas can be dangerous
and is PROHIBITED.
● The appliance must be installed in accordance with the
instructions and local regulation.
● A well ventilated area must have a minimum of 25% of the
surface area open. The surface
area is the sum of the walls surface.
● This appliance is intended for decorative purposes
ASSEMBLY AND USER INSTRUCTIONS
FOR OUTDOOR USE ONLY
1. Read the instructions before using the appliance.
2. Warning: Accessible parts may be very hot, keep young
children away.
3. Close the valve of the gas bulb or the regulator after use.
4. For use outdoors and in well ventilated areas.
5. The use of this appliance in enclosed areas can be
dangerous and is PROHIBITED.
6. The appliance must be installed in accordance with the
instructions and local regulation.
7. A well ventilated area must have a minimum of 25% of the
surface area open. The surface area is the sum of the walls
surface.
Your new fire pit is made from the high quality and eco-friendly
materials, and produced under strict manufacturing controls.
Please read the Instructions before assembly follow the instructions
for use carefully. We congratulate you on your decision to buy this
outdoor gas fire pit and wish you great fun when warming with it.
02 03

IMPORTANT SAFETY INSTRUCTIONS
1. Please change the gas bulb in an amply ventilated area, away from any
ignition source candle, cigarettes, other flame producing appliances.
2. Please check that the regulator seal is correctly fitted and able to fulfill
its function.
3. Do not obstruct the ventilation holes of the bulb housing.
4. Please close the gas supply at the valve of the gas cylinder or the
regulator after use.
5. In the event of gas leakage, the appliance shall not be used or if alight,
the gas supply shall be shut off and the appliance shall be investigated and
rectified before it is used again.
6. Please check the tubing or the flexible hose at least once per month and
each time the cylinder is changed. If it shows signs of cracking, splitting or
other deterioration, it shall be exchanged for new hose of the same length
and of the equivalent quality.
7. Please check the tightness of the connections of the gas line supply,
including gas cylinder valve/regulator, regulator/hose, hose/appliance gas
inlet.
8. The appliance area must be kept clear and free from combustible
materials, gasoline, and other flammable vapors and liquids.
9. Do not use this appliance if any part has been under water. Immediately
call a qualified service technician to inspect the appliance and to replace
any part of the control system and any gas control that has been under
water.
10. Children and adults should be alerted to the hazards of high surface
temperatures and should stay away to avoid burns or clothing ignition.
11. Young children should be carefully supervised when they are in the area
of the appliance.
12. Clothing or other flammable materials should not be hung from the
appliance or placed on or near the appliance.
13. Any guard or other protective device removed for servicing the
appliance shall be replaced prior to operating the appliance.
14. Installation and repair should be done by a qualified service person. The
appliance should be inspected before use and at least annually by a
qualified service person. More frequent cleaning may be required as
necessary. It is imperative that the control compartment, burners, and
circulating air passageways of the appliance are kept clean.
15. DO NOT burn solid fuels in this appliance.
16. This outdoor gas appliance is intended for warming purpose.
17. This outdoor gas appliance is for Outdoor Use ONLY.
18. This outdoor gas appliance is not intended to be installed in or on
recreational vehicles and/boats.
19. This outdoor appliance is not for use on wood decks or other flammable
surface.
20. Before each use of this gas appliance, open the door and/or the Gas
Tank Drawer and inspect the hose. If there is evidence of excessive
abrasion or wear or if the hose is damaged, the hose assembly must be
replaced prior to the appliance being put into operation. Use only the
replacement hose assembly specified in this manual. Make sure to leak test.
21. Before each use of this gas appliance, inspect the burner. The burner
must be replaced prior to the appliance being put into operation if it is
evident that the burner is damaged. Use only the replacement burner
specified in this instruction.
22. Make sure to properly locate the gas hose including locating the hose
out of pathways where people may trip over it or in areas where the hose
may be subject to accidental damage.
23. Keep the fuel supply hose away from any heated surface.
24. Never use this appliance closer than 3 meters from anything flammable,
including houses or overhead tree branches.
25. Never use gasoline, kerosene, or any other liquid fuel to start a fire.
26. Always maintain a safe distance from the fire.
27. Always supervise children around the fire.
28. Never leave a fire unattended.
29. The appliance is hot during and after use, always allow ample cooling
time before touching or moving.
EN
04 05

1. Read the instructions before installation and use.
2. This appliance must be installed and the gas bulb should be stored in
accordance with the regulations in force.
3. Do not obstruct the ventilation holes of the bulb housing.
4. Do not move the appliance when in operation.
5. Shut off the valve at the gas bulb or the regulator before moving the
appliance.
6. The tubing or the flexible hose must be changed within the prescribed
intervals.
7. Use only the type of gas and the type of bulb specified by the
manufacturer.
8. In case of violent wind particular attention must be taken against tilting
of the appliance.
9. Keep the instructions for future reference.
10. For use outdoors or in amply ventilated areas.
11. An amply ventilated area must have a minimum of 25% of the surface
area open.
12. The surface area is the sum of the walls surface.
13. Be careful, accessible parts may be very hot. Keep away from young
children.
WARNING
The gas fire pit, with gas type l3+, is designed to fit with butane gas
cylinder. Gas consumption, gas pressure and injector orifice size are listed
in the below table.
Gas consumption
1199 g/h 28-30mabr 2.05 mm
Gas pressure Injector orifice size
DO NOT use this appliance with an adjustable regulator. We suggest you
use this appliance with butane gas cylinder listed as below table.
Gas cylinder dimension Gas cylinder weight
Dia30.8 x 31cmH 5.5 KG
SPECIFICATIONS
EN
AA
BB
EE
CC
DD
B
A
F
I
H
E
M
D
CG
J
L
K
PACKAGE CONTENTS
DESCRIPTIONPART QUANTITY
A
B
C
D
E
F
G
H
I
J
K
L
M
AA
BB
CC
DD
EE
Table top assembly
Front panel
Door panel
Back panel
Right panel
Front-right leg
Front-left leg
Back-left leg
Back-right leg
Gas cylinder support
Lava rock
Weather cover
Door handle
Bolt (M6 x 15)
Bolt (M6 x 25)
Washer (M6)
Hex screw driver
Bolt (M4 x 10)
1
1
1
1
1
1
1
1
1
1
2
1
1
16
4
20
1
1
06 07

EN
I
HD
Figure 4
DD
AA
CC
1. Carefully unpack all parts from the box, compare parts with package
content listed above, make sure all parts are present before beginning
assembly of product. If any part is missing or damaged, do not attempt to
assemble the product.
2. Attach back-left leg (H) and back-right leg (I) and front-left leg (G) and
front-right leg (F) to table top assembly (A) with bolts (AA) and washer (CC)
by using hex screw driver (DD), (see Figure 1).
NOTE: DO NOT tighten the screws completely.
Hardware Used:
AA Bolts (M6 x 15) x 4
CC Washer (M6) x 4
DD Hex screw driver x 1
3. Attach front panel (B) to front-left leg (G) and front-right leg (F) with
bolts (AA) and washer (CC) using hex screw driver (DD), (see Figure 2).
NOTE: DO NOT tighten the screws completely.
Hardware Used:
AA Bolts (M6 x 15) x 4
CC Washer (M6) x 4
DD Hex screw driver x 1
F
A
I
H
G
Figure 1
DD
AA
CC
B
F
G
Figure 2
DD
AA
CC
F
I
E
Figure 3 DD
AA
CC
ASSEMBLY INSTRUCTIONS ASSEMBLY INSTRUCTIONS
4. Attach right panel (E) to front-right leg (F) and back-right leg (I) with
bolts (AA) and washer (CC) using hex screw driver (DD), (see Figure 3).
NOTE: DO NOT tighten the screws completely.
Hardware Used:
AA Bolts (M6 x 15) x 4
CC Washer (M6) x 4
DD Hex screw driver x 1
5. Attach back panel (D) to back-left leg (H) and back-right leg (I) with bolts
(AA) and washer (CC) using hex screw driver (DD), (see Figure 4).
NOTE: DO NOT tighten the screws completely.
Hardware Used:
AA Bolts (M6 x 15) x 4
CC Washer (M6) x 4
DD Hex screw driver x 1
08 09

ASSEMBLY INSTRUCTIONS ASSEMBLY INSTRUCTIONS
EN
EE
CAUTION: please be advised that this fire pit is equipped with natural
lava rock that may crackle or pop the first time it is used. The lava
rock has been pre-heat treated to release any natural inherent
moisture. However, in rare cases on first time use, the lava rock may
pop or burst causing small pieces of hot rock to potentially be a
projectile. These hot pieces could cause injury or property damage. As
a precaution, please follow these instructions the first time the fire pit
is used:
(1). On first use, do not stand over or near the fire pit once lit.
(2). Light the fire pit and let it run on high for 20 minutes.
(3). Once lit, do not go within 3.6m of the fire pit for at least the first
20 minutes on the first use to ensure any residual moisture trapped in
the rocks gets released.
(4). After the first heating cycle, there is little further concern. It is
rare that any crackling will happen on the first use, this is simply a
precaution.
(5). Keep lava rock covered and dry when not in use to prevent
additional moisture from getting in the rocks.
(6). If lava rocks are exposed to moisture after first use, run the
burner on low to gradually warm and dry the rocks before repeating
steps 1 through 3.
H
C
I
F
G
H
J
BB
DD
CC
Figure 5
Figure 6
Figure 7
C
M
6. Attach gas cylinder support (J) to back-left leg (H) and back-right leg (I)
and front-left leg (G) and front-right leg (F) with bolts (BB) and washer (CC)
using hex screw driver (DD), (see Figure 5).
NOTE: Tighten all screws completely.
Hardware Used:
BB Bolts (M6 x 25) x 4
CC Washer (M6) x 4
DD Hex screw driver x 1
7. With the help of another person, carefully turn the fire pit to the upright
position. Attach the door panel(C) to the back-left leg (H) by aligning the
hinge on the door panel with those on the back-left leg (H) and inserting the
pins in the hinges, (see Figure 6).
8. Attach the door handle (M) to the door panel (C) with the bolt (EE) using
a Phillips screwdriver (NOT included), (see Figure 7).
Hardware Used:
EE Bolt (M4 x 10) x 1
9. Open the box of lava rocks, put the lava rocks (K) into the fire bowl of the
fire table, (see Figure 8). A gas fire pit requires 6kg lava rocks.
WARNING: keep children away during assembly, as this item contains lava
rock, which are small pieces and can be swallowed by children.
NOTE: leave the pilot box uncovered by the lava rock.
10 11

ASSEMBLY INSTRUCTIONS ASSEMBLY INSTRUCTIONS
EN
Figure 10
L
Figure 9
manifold inlet fitting gas regulator
Figure 8
pilot box
K
10. Please use a flexible hose with a length less than 50cm
11. Please use a regulator complied with standard EN16129.
12. Clip directly the gas regulator onto the manifold inlet fitting (see
Figure 9).
13. Cover the fire pit with the outdoor weather cover (L) when not in
use to protect it from the elements or when fire pit is cool COMPLETELY
after the use (see Figure 10).
12 13

1. Make 2~3 oz. of leak solution by mixing one part liquid dishwashing
detergent and three parts water. Noted: make sure control knob is “OFF”.
2. Apply several drops of solution where the gas cylinder valve attaches to
regulator (see Figure 12), inspect the solution at the connection looking for
bubbles. If NO bubbles appear, the connection is secure. If bubbles appear,
the connection has the leak, disconnect the regulator, reconnect, perform
another leak check. If you continue to see bubbles after several attempts,
cylinder valve is defective and should be returned to cylinder’s supplier.
3.Apply several drops of solution where hose attaches to appliance gas
inlet (see Figure 13), where the regulator attaches to hose (see Figure 14).
If NO bubbles appear, the connections are secure.
If bubbles appear, the connection has the leak, disconnect, reconnect,
perform another leak check.
If you continue to see bubbles after several attempts, the part is defective
and should replace the part.
To perform a leak test:
To prevent fire or explosion hazard when testing for a leak:
1. Always perform the leak test as described below before lighting this
appliance or each time the gas bulb is connected for use.
2. Do not smoke or allow other sources of ignition in the area while
conducting a leak test.
3. Conduct the leak test outdoors in a well-ventilated area.
4. Do not use matches, lighters or a flame to check for leaks.
5. Do not use this appliance until any and all leaks are corrected. If you are
unable to stop leak, disconnect the propane supply. Call a gas appliance
service shop or your local propane gas supplier.
LEAK TEST
EN
Figure 11
Make sure the control knob is in the “OFF” position. Unscrew the push
button cap on the ignitor module located on the control panel to access the
battery compartment. The ignitor module requires one AAA size battery
(see Figure 11), BATTERY IS NOT INCLUDED.
WARNING:
1. Please observe proper polarity and use the correct battery type when
placing or replacing the battery. Improper installation could result in
ignition failure.
2. Please remove the battery if consumed or if product is to be left unused
for a long period of time.
BATTERY
OFF (APG.)
MAX
(MÁX.)
1 AAA
1.5V
IGNITOR
( Encendedor )
ON/MIN
(ENC./MÍN.)
LIGHTING INSTRUCTIONS
1. Push in gas control knob slightly and
2. Turn gas control knob to “ON/MIN”.
3. Push in gas control knob all the way
4. If the burner does not light in 15
1. Push in gas control knob slightly and turn to “OFF”.
TO TURN OFF GAS
turn to “OFF”.
and hold. Continue to press the
ignition button for 15 seconds.
seconds, release the knob and it will
pop back out. Wait 5 minutes before attempting
to light the burner again, repeat step 1 to 3.
14 15
INSTRUCTIONS D'ALLUMAGE
1. Enfoncez légèrement le bouton de contrôle du gaz et tournez-le sur
« OFF ».
2. Tournez le bouton de contrôle du gaz sur «ON/MIN».
3. Enfoncez complètement le bouton de contrôle du gaz et
maintenez-le enfoncé. Continuez à appuyer sur le bouton d'allumage
pendant 15 secondes.
4. S le brûleur ne s'allume pas dans les 15 secondes, relâchez le
bouton et il sortira. Attendez 5 minutes avant d'essayer de rallumer le
brûleur, répétez les étapes 1 à 3.
POUR COUPER LE GAZ
1. Enfoncez légèrement le bouton de contrôle du gaz et tournez-le sur
« OFF ».

TO TURN OFF GAS
LIGHTING INSTRUCTIONS
1. Push in gas control knob slightly and turn to “OFF”.
2. Turn gas control knob the “ON/MIN”.
3. Push in gas control knob all the way and hold. Continue to press the
ignition button for 15 seconds.
4. If the burner does not light in 15 seconds, release the knob and it will pop
back out. Wait 5 minutes before attempting to light the burner again, repeat
step 1 to 3.
1. Push in gas control knob slightly and turn to “OFF”.
WARNING: for your safety, read and follow the Lighting Instructions in this
manual and in the Rating Plate on the appliance. IMPROPER LIGHTING
PROCEDURES COULD RESULT IN A FIRE HAZARD OR EXPLOSION HAZARD
OR PROPERTY DAMAGE, INJURY OR LOSS OF LIFE.
gas cylinder valve /
regulator connection
(Figure 12)
hose / appliance gas
inlet connection
(Figure 13)
regulator / hose
connection
(Figure 14)
Observe Flame Height When Lit: The burner will display blue and
yellow flames. These flames should be a blue / yellow color between
2.5cm-5cm height, (see Figure 15). These flames should not be
yellow or produce thick smoke. This would indicate an obstruction of
airflow through the burners. The flames should be blue with straight
yellow tops.
Figure 15
Yellow
Yellow
Light Blue
Light Blue
Blue Blue
Good Bad
EN
16 17

To enjoy the outstanding performance from your fire pit, make sure
you perform the following activities on a regular basis:
1. Use warm soapy water for cleaning. Never use flammable or
corrosive cleaning agents.
2. While cleaning the fire pit, make sure to keep the area around
the burner dry at all times. DO NOT submerge the control valve
assembly. If the gas control is submerge in water, DO NOT use it. It
must be replaced.
3. Air flow must be unobstructed. Keep controls, burner, and
circulating air passageways clean. Signs of possible blockage
include:
(1). Gas odor with extreme yellow tipping of flame.
(2). Fire pit does NOT reach the desired temperature.
(3). Fire pit flame is excessively uneven.
(4). Fire pit makes popping noises.
(5). Spiders and insects can nest in burner or orifice. This
dangerous condition can damage fire pit and render it unsafe for
use. Clean burner holes by using a heavy-duty pipe clearer.
Compressed air may help clear away small particles.
4. Carbon deposits may create a fire hazard. Clean burner with
warm soapy water if any carbon deposits develop.
5. Cover your fire pit with an outdoor weather cover when not in
use to protect it from the elements.
NOTE: always allow fire pit to cool COMPLETELY before you cover
the fire pit with an outdoor weather cover or you attempt to service
or perform maintenance.
CARE AND MAINTENANCE REPLACEMENT PARTS LIST
EN
Door panelC
B
A
D
E
F
F210020-A-B
F210020-D
F210020-E
F210020-F
F210020-G
G
Back panel
Right panel
Front-right leg
F210020-H
H
Front-left leg
F210020-I
I
Back-left leg
J
K
L
F210020-J Back-right leg
F210020-K Gas cylinder support
ET-T-250 Firepit thermocouple, 250 mm/10"
ET-FL03 Firepit foot leveler 03, 32 x 23 mm
F200083-A1-ET Firepit electrode 3" tip, wire 300mm
for 40000, 50000 BTU
CLTN-PLSELT Firepit pulse ignition
EFP-CNNB Firepit control knob ET, large #6
EFP-LVRK-13.2 Firepit lava rock (red)
M
F210020-M Weather cover
N
EFP-DH Firepit door handle ET
Table top assembly
F210020-C Front panel
NO PART# DESCRIPTION
18 19