Costway HW67778 User manual

PLEASE READ AND KEEP FOR FUTURE REFERENCE.
THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION.
USER’S MANUAL
Rattan Sun Lounger
HW67778

Hardware inside
Contact our friendly customer service department for help first.
Read each step carefully before starting. It is very important to
ensure each step followed in correct order, otherwise assembly
difficulties may occur.
Most of board parts are labeled or stamped on the raw edges.
Have a check to make sure all parts are included.
Work in a spacious area, preferably on a carpet close to where
the unit will be used.
Keep the hand tools close at hand. Do not use power tools to
assemble your furniture. They may scratch or damage the parts.

Notice:
1. 50% Tighten before fixing all screws, Allen wrench is
recommended instead of an electric drill.
2. Place the item on a flat ground to adjust and make sure
it remains stable
3. Tighten up all screws with tools gradually.
4. If the screws are not aligned with holes during assembly,
please loosen all the other screws to 50% and continue
the assembly process.
5. If the item is not stable, please loosen all the screws,
adjust it on a flat ground and tighten up all screws again.
6. Note : If one or some screws are fully tightened during
assembly, chances are the others will not be aligned with
holes. In addition, all the holes are designed to be relatively
larger to provide more space for the adjustment of the screws.
3
AE
B
C
D
F
I
J
G
H
K
L

Part & Hardware List
Right Frame (1pc)
A B
Left Frame (1pc)
C
D
Side Left Frame (1pc)
Side Right Frame (1pc)
Front Frame (1pc)
E F
Seat Frame (1pc)
G
Back side Frame (1pc)
H
Back Frame (1pc) Right Arm (1pc)
I
Left Arm (1pc)
J K
Seat Cushion (1pc)
1
Bolt M6 x 20 mm (2 pcs)
2
Bolt M6 x 30 mm (12 pcs)
3
Bolt M6 x 40 mm (8 pcs)
Bolt M6 x 55 mm (2 pcs)
4 5
M6x1 Washers (24 pcs)
6
4
L
Pillow (1pc)
Allen key M4 (2 pc)

STEP 1
STEP 3
Connect part from STEP 1 & Front Frame (E) & Back side Frame (G) with Bolt (2) & Washers (5)
2
STEP 2
B
D
A
C
5
2
2
2
G
E
Connect Left Frame (B) & Side Left Frame (D)
with Bolt (2) & Washers (5)
Connect Right Frame (A) & Side Right Frame (C)
with Bolt (2) & Washers (5)

6
STEP 4
Connect part from STEP 2 & STEP 3 with Bolt (2) & Washers (5)
2
2
STEP 5
Connect part from STEP 4 & Seat Frame (F) with Bolt (2), (3) & Washers (5)
F
3
3
3
2
2
3
3
3

7
STEP 6
Connect part from STEP 5 & Back Frame (H) with Bolt (1) & Washers (5)
1
1
H
STEP 7
Connect part from STEP 6 & Left Arm (J) with Bolt (2), (3), (4) & Washers (5)
J
2
3
4

8
STEP 8
Connect part from STEP 7 & Right Arm (I) with Bolt (2), (3), (4) & Washers (5)
I
4
3
2
STEP 9
Backrest tilt angle can be adjusted

STEP 10
Put on Seat Cushion (K) & Pillow (L) to Complete Sun lounger
9
K
STEP 11
FINISH
L

10