Cove SIMPLE 1 User manual

User
Manual
www.covesmart.com

DOOR
SENSORS
Page 15
MEDICAL
PENDANTS
Page 17
KEY
REMOTES
Page 18
CO
DETECTORS
Page 21
SMOKE + CO
DETECTORS
Page 23
SMOKE/HEAT/FREEZE
DETECTORS
Page 19
MOTION
SENSORS
Page 11
TOUCHSCREEN
PANEL
Page 1
WINDOW
SENSORS
Page 13
Table of Contents

FLOOD + FREEZE
SENSORS
Page 24
YARD SIGN +
WINDOW STICKERS
Page 27
GLASS BREAK
DETECTORS
Page 25
Page 29
MOBILE
APP
Page 28
REGULATORY STATEMENTS,
WARNINGS, NOTICES + WARRANTY

Touchscreen Panel
INSTALLATION + LOCATION
PANEL BUTTONS
STATUS BAR ICONS
PANEL DISPLAY
SYSTEM SOUNDS
ALARMS
USER PASSCODES
MESSAGES + ALERTS
HISTORY
EXIT+ TRANSMISSION DELAY
SYSTEM INFO
SENSORS
SYSTEM/SENSOR TESTS
2
3
3
4
4
5
7
8
8
8
9
9
10
1www.covesmart.com

INSTALLATION + LOCATION
does not
not
2
Your panel serves as the heart of your system. It should be placed in a central
location within your home. The panel must be within 5 feet of an electrical outlet
that does not have a ground fault circuit interrupter (GFCI) button and is not controlled
by a switch. Secure the plug to the outlet with the provided screw to avoid accidental
power failure. After the panel is plugged in, it will establish communication with the
monitoring center. This may take several minutes.

Button LED Emergency Call Status
STATUS BAR ICONS
LOW
BATTERY
BATTERY
FULL
BATTERY
CHARGING
MESSAGES NEW
MESSAGE
NO CELLULAR
CONNECTION
AC POWER
CONNECTED
NO AC
POWER
PANEL BUTTONS
HOMEBUTTON
Button LED Status
EMERGENCY CALL BUTTON
3
A motion sensor was triggered

PANEL DISPLAY
ADJUST SCREEN BRIGHTNESS
ADJUST THE DISPLAY TIMEOUT TIME
CLEAN SCREEN
TURN LEDBUTTONS ON/OFF
SYSTEM SOUNDS
ADJUST THE PANEL VOLUME
TURN CHIME SOUND ON/OFF (FOR ALL SENSORS)
ADJUST THE TOUCH SCREEN VOLUME
TURN VOICE SOUND ON/OFF (FOR ALL SENSORS)
CHANGE THE VOICE GENDER (MALE/FEMALE)
TEST THE SIREN
4

ALARMS
ARMING THE SYSTEM
Stay Mode -
Away Mode -
Auto Stay Mode -
Bypass Sensors -
DISARMING THE SYSTEM
5

CANCELING ANALARM/FALSE ALARMS
BURGLARY ALARM
USING THE OPTIONAL HOSTAGE CODE
FIRE ALARM
6

CARBON MONOXIDE (CO) ALARM
FLOOD ALARM
USER PASSCODES
MASTER PASSCODE
VERBAL PASSWORD
RESET MASTER PASSCODE
HOSTAGE PASSCODE
RESET HOSTAGE PASSCODE
ADD NEW USER PASSCODE
RESET USER PASSCODE
REMOVE USER PASSCODE
7

SECURE ARMING
MESSAGES + ALERTS
MESSAGES
TROUBLE ALERT MESSAGES AND AUDIBLEALERTS
HISTORY
EXIT + TRANSMISSION DELAY
EXITDELAY
8

TRANSMISSION DELAY
SYSTEM INFO
SENSORS
ADD A SENSOR
REMOVE A SENSOR
RENAME A SENSOR
LONG TERM BYPASS A SENSOR
TURN CHIME ON/OFF
TURN VOICE ON/OFF
9

TEST SENSOR
SWINGER SHUTDOWN
CROSS ZONING
SYSTEM/SENSOR TESTS
COMPLETE SENSOR SIGNAL TEST
SENSOR SIGNAL WALK TEST
10
once every month. All system tests can be
technical support at 1-855-268-3669.
technical support at 1-855-268-3669 if any tested sensor fails to reach verified status.
technical support at 1-855-268-3669 if any tested sensor fails.

Motion Sensors
INSTALLATION + LOCATION
11
SEE PAGE 9 FOR REFERENCE TO:
CORNER
PLACEMENT
WALL
PLACEMENT
6-8
FEET
Sensors have a 90º field of view and detect motion up to 45 feet away.

ENTRY DELAY
ACTIVE IN STAY MODE
SENSITIVITY
DETECTINGPETS
TESTING SENSOR
CHANGING BATTERIES
12
Motion Sensors have a 0 second entry delay. It is recommended to keep the
Motion Sensors is protecting an area that is rarely used. To
Motion Sensors are set to high sensitivity to prevent false alarms. To change
Motion Sensors will not detect a body under 55 pounds. To change this setting
Motion Sensor’s signal to the panel, tap Settings > Motion Sensors > (select
Motion Sensors require one CR123A battery. Press in on the recessed tab at the bottom
After replacing the batteries it is recommended that you
test the sensor to make sure it works properly.

INSTALLATION + LOCATION
Window Sensors
SEE PAGE 9 FOR REFERENCE TO:
13
1/2” Max
Magnet Contact
Sensor
1/2” apart and align the two semi-circles

TESTING SENSOR
CHANGING BATTERIES
14
1/2” Max
Operable Window
Wall/Frame
Window Sensors require two CR2032 batteries. Open the contact sensor (large piece) by
Use a screwdriver to slide the batteries out from under the black padded circles.
After replacing the batteries
it is recommended that you test the sensor to make sure it works properly.

INSTALLATION + LOCATION
SWINGING DOOR
SEE PAGE 9 FOR REFERENCE TO:
Door Sensors
15
1/2” Max
Magnet Contact
Sensor
CorrectCorrect Incorrect
1/2” apart and align the two semi-circles

SLIDING DOOR
DOUBLE DOOR
ENTRY DELAY
TESTING SENSOR
CHANGING BATTERIES
16
Sensors have a 30 second entry delay to allow the user time to disarm
Near the top on the least used door (or secured door), place the contact sensor
with the alignment mark facing the other door. Place the magnet on the door or the
frame between the two doors.

Medical Pendants
TRIGGERING PENDANT
TESTING PENDANT
CHANGING BATTERIES
17
sure the + sign is facing towards you. Replace the cover and tighten the 4 screws.
Medical Pendants require one CR2032 battery. To change the battery, remove the bottom
cover by using a screwdriver to remove the 4 screws. Use a screwdriver to slide the batteries
out from under the black padded circles. When installing the new battery, make sure the +
sign is facing towards you. Replace the cover and tighten the 4 screws. After replacing the
batteries it is recommended that you test the sensor to make sure it works properly.
SEE PAGE 9 FOR REFERENCE TO: