Coverstar Eclipse User manual

Eclipse Use & Care Guide
Pool Safety Tips

2
Welcome to the rapidly growing group of pool owners who enjoy the ease and convenience of Eclipse automatic safety cover system. We work hard to provide the best
engineering and highest quality materials to make you a satisfied customer and a happy pool owner.
Please read this owner’s guide and follow its instructions carefully. It is designed to acquaint you with the features of your new cover system and to help you operate and
maintain your system properly. The information here is the accumulated knowledge of thousands of installations. If you receive conflicting information elsewhere, please
call Coverstar for clarification.
Coverstar is a “wholesale only” manufacturer of pool cover systems. We have selected the most qualified professional distribution companies to represent our products
throughout the world. They will provide you with the local service and maintenance that you may require. The enclosed warranty page has all the warranty information for
your specific system and cover material.
Warranty Registration
In order to receive warranty service, please register your cover system with the manufacturer as soon as it is fully installed using the
dealer/distributor information and warranty ID# provided. To do this:
Go to www.coverstar.com and click on the Product Registration button on the home page. Fill out the online registration form and submit it.
OR Fill out the postage paid registration card and mail it.
For your information, fill in your Dealer / Distributor Information below:
Dealer / Distributor Information
Dealer/Distributor Name
Address
City State ZIP
Phone
Date Installed
By
Warranty Information Table of Contents

3
ASTM required safety warning................................................................................................4
Pool water level..........................................................................................................................4
Using the cover pump...............................................................................................................4
Aluminum lid ..............................................................................................................................5
Key switch location....................................................................................................................5
Partially covered pools..............................................................................................................5
Safety Instructions
Operating Instructions
Cover Care &
System Maintenance
Installation Safety Checklist
& Trouble Shooting
Pool Safety Tips
Warranty Information Table of Contents
Pool cover operators .................................................................................................................6
Covering the pool.......................................................................................................................6
Covering the pool manually ......................................................................................................6
Uncovering the Pool ..................................................................................................................7
Uncovering the pool manually.................................................................................................. 7
Customer sign off list & trouble shooting ..............................................................................10
Cover will not move forward or will not reverse....................................................................10
Water leaking onto cover ........................................................................................................10
Cover retracts out of square................................................................................................... 10
Cover not even at end of pool.................................................................................................10
Cover seems to be running under stress ..............................................................................10
System Diagram......................................................................................................................11
Information in this user guide is believed to be accurate at time of printing. Coverstar, Inc. reserves the right to make product and
instructional changes over time without notice. Visit www.coverstar.com for the latest information and updates to this user guide.
Pool Safety Tips........................................................................................................Back Cover
Water level.................................................................................................................................. 8
Pool chemistry ........................................................................................................................... 8
Cleaning the cover..................................................................................................................... 8
Tracks ......................................................................................................................................... 8
Housing drains........................................................................................................................... 8
Mechanism and pulleys............................................................................................................ 9
Preventing rodent damage....................................................................................................... 9
Adjustments and minor repairs................................................................................................ 9
Adjusting the torque limiter.......................................................................................................9
Patching the cover..................................................................................................................... 9
Winterizing the cover.................................................................................................................9

4
Safety Instructions
POOL WATER LEVEL
Maintain the water level at the middle
elevation of the skimmer opening.
If the water drops below this level,
the cover may operate under stress.
Never cover the pool without the
proper water level under the cover.
The water supports all weight on the
surface of the cover. If the water level
is low and water builds up on the cover, severe damage may be done to
the coping and/or cover system.
USING THE POOL COVER PUMP
Water accumulation on the top of the cover can come from rain, snow,
overspraying sprinklers, or leaks that may develop in the cover. Even
what appears to be small amounts of water spread over the whole
surface of the cover can migrate and accumulate in depressions. This is
dangerous. Any accumulation of water on the surface of the cover must
be removed immediately using the cover pump. The cover is not a
safety cover unless the pump is in place.
s %VERY COVER SYSTEM COMES WITH A PUMP THAT AUTOMATICALLY SENSES WATER
and removes it, provided the pump is operable, properly placed, and maintained
according to the pump manufacturer’s instructions.
s !FTER THE PUMP IS PLACED UPRIGHT ON ITS BASE IN THE MIDDLE OF THE COVER PLUG IT
into a G.F.C.I. protected outlet. If the pump does not turn on immediately, it will
reset itself automatically. This can take up to five minutes. Consult the pump’s
user manual for any operational or service problems.
s $URING THE WINTER THE PUMP WILL FREEZE INTO THE ICE WITHOUT DAMAGE !S THE
ice melts during the winter, the pump will
automatically activate. Make sure to keep
power to the pump and the discharge
hose free of kinks.
s 9OU MUST FOLLOW ALL PUMP
manufacturer’s instructions regarding its
1. READ AND FOLLOW ALL INSTRUCTIONS.
2. WARNING: To reduce the risk of injury, do not permit children to use this
product unless they are closely supervised at all times.
3. All field-installed metal components such as rails, ladders, drains, or other
similar hardware within 3m of the unit shall be bonded to the equipment
grounding bus with copper conductors not smaller than No. 8 AWG (No. 6 AWG
for Canada.)
4. Keep the pump on the cover and set up for proper use whenever the cover
is over the pool.
5. Check cover frequently for signs of premature deterioration or weakness.
6. SAVE THESE INSTRUCTIONS.
This user guide is intended to instruct cover system owners in the proper operation and maintenance of
their cover system. If a salesman or installer gives information that contradicts this user guide, you should
disregard their instruction on that topic.
Warning: A cover with water on it poses the same safety hazard as an open pool.
Warning: A child can create a depression on the cover great enough to collect a
dangerous amount of water.
)-0/24!.4 3!&%49 ).3425#4)/.3

5
s !VOID USING EXTENSION CORDS
s )F YOUR PUMP OR CORD BECOMES DAMAGED REPLACE THE PUMP IMMEDIATELY
s 0LUG THE PUMP INTO A '&#) 0ROTECTED OUTLET ONLY 0LACE THE PUMP ON THE COVER lRST THEN PLUG IN THE PUMP
DO NOT stand on a wet surface while using the pump.
s !VOID CONTACTING ACCUMULATED SURFACE WATER ON YOUR COVER WHEN THE PUMP IS ON THE COVER
%LECTRIC SHOCK IS POSSIBLE 9OUR PUMP SHOULD NOT BE USED FOR ANY APPLICATION OTHER THAN SPECIlED IN THESE INSTRUCTIONS
s 9OUR PUMP HAS BEEN PROVIDED WITH A STABILIZER PLATE SO IT REMAINS UPRIGHT $/ ./4 ALLOW THE PUMP TO TIP OVER
7!2.).' 9OUr pump is an electric appliance and caution should be used when handling your pump and electric cord around water.
ALUMINUM LID
The aluminum lid on below-deck systems is a long-lasting cosmetic cover for the housing. It is not intended for anyone to walk or step on. It can be
slippery when wet and walking on it can loosen the support brackets under it. Instruct children not to step on the lid.
+%9 37)4#( ,/#!4)/.
All controls for the cover system must be located where the pool is completely visible during cover operation. All plants and shrubs should be
maintained for continuous visibility.
0!24)!,,9 #/6%2%$ 0//,3
It is extremely important to always cover or uncover the pool completely. Never leave the pool partially covered. A partially covered pool presents a
serious danger as people or pets may drown under the cover.
7!2.).' A partially covered pool can pose a safety hazard. Never leave the cover over the pool in a partially covered
position. Always completely cover or uncover the pool. Even children or pets who can swim may drown if they lose their
orientation under the cover. Never allow anyone to swim under the cover.
use and maintenance.
s !Fter the pump has removed all water from one location on the cover, it may be necessary to move the pump to other locations to remove all accumulated water.
s 4HE PUMP IS COVERED UNDER THE PUMP
manufacturer’s warranty.
s &OR SERVICE RETURN IT TO THE MANUFACTURERS SERVICE CENTER

6
Operating Instructions
POOL COVER OPERATORS /NLY INSTRUCTED RESPONSIBLE INDIVIDUALS SHOULD OPERATE THE COVER &OR THIS REASON ALL SYSTEMS ARE KEY CONTROLLED 4HIS IS AN EXPENSIVE PIECE OF
EQUIPMENT AND LIKE YOUR AUTOMOBILE SHOULD BE OPERATED ONLY BY SOMEONE WHO CAN EXERCISE JUDGMENT AND CARE #HILDREN SHOULD NOT BE PERMITTED TO USE THIS PRODUCT UNLESS THEY ARE CLOSELY
supervised at all times.
7!2.).':$O NOT OPERATE THE COVER WITH WATER ON IT *UST ONE INCH OF WATER ON A COVER CAN WEIGH THOUSANDS OF POUNDS
COVERING THE POOL
1 Unlock the switch cover. Toggle the switch to the “cover” position. It takes a second for the gear to engage the rope take-up reels. Safety covers are
required to have a momentary power switch that requires constant pressure to operate the motor. This keeps the operator in complete control of
the mechanism.
 (OLD THE SWITCH IN THE hCOVERv POSITION UNTIL THE COVER EXTENDS TO THE POSITION REQUIRED FOR YOUR POOL COVER MODEL
A. For “Underguide” systems, where guides are mounted under the pool coping, lightly bump the leading edge against the end of the pool.
Do not continue to force the cover closed after it touches the coping.
" &OR h4OPGUIDEv SYSTEMS WHERE THE GUIDES ARE MOUNTED ON TOP OF OR IN THE DECK THE COVER SHOULD EXTEND OVER THE POOL BUT STOP SEVERAL INCHES SHORT OF
reaching the end pulley housings at the end of the guides. Make sure the leading edge of the pool cover clears the top surface of the deck to prevent
damage to the bottom of the leading edge or its fabric cover.
3 Release the switch when you have reached the proper closed position discussed above. Close the switch lid, lock it, and remove the key.
4 Place the pump on the cover.
Note: If the cover hesitates or stops before it reaches the end of the pool, you should immediately release the switch and investigate the problem. Sometimes
dirt, debris, or obstacles like towels or hoses can stop the cover. Remove the obstruction and continue covering the pool. If, after investigation, you cannot find
a reason for the hesitation, you should reverse the direction of the cover a foot or two and then retry to cover the pool. If the same thing occurs, immediately
release the switch and call your SwimWise distributor. Continuing to operate the cover can cause damage not covered by the manufacturer’s warranty.
#/6%2).' 4(% 0//, -!.5!,,9
If there is a loss of electrical power to the system and the cover must be closed for safety or other reasons, the cover can be closed manually.
This is not easy to do, but it can be done by following these steps:
1 Remove the cover lid.
 0ULL THE ROPES TO EXTEND THE COVER OUT OVER THE POOL
Note: For large pools, it may be necessary to loosen the cover mechanism’s torque limiter to close the pool.
1
4
3
Topguide System
2B
Underguide System
2

7
UNCOVERING THE POOL
WARNING: $O NOT OPERATE THE COVER WITH WATER ON IT *UST ONE INCH OF WATER ON A COVER CAN WEIGH THOUSANDS OF POUNDS
1 Remove any objects from the cover including the pump.
2 Unlock the switch cover. Toggle the switch to the “uncover” position.
 (OLD THE SWITCH IN THE hUNCOVERv POSITION UNTIL THE COVER EXTENDS TO THE POSITION REQUIRED FOR YOUR POOL COVER MODEL
A. For “Underguide” systems, where the cover is attached to the underside of the pool deck, retract the cover until the front edge of the cover is 6
inches from the cover housing lid.
B. For “Topguide” systems, where the guides are mounted on top of or in the deck, the cover should be retracted to a point several inches in front of
the emergency stops on the cover guides. Make sure the leading edge of the pool cover clears the top surface of the deck to prevent damage to the
bottom of the leading edge or it’s fabric cover. The stops are there to prevent pulling the cover out of the guides in the event of over-retraction, but
are not meant as a stop to run the cover up against. Driving the cover into the end pulley housings or retracting against the emergency stops on a
regular basis may damage several components, including the cover, rope, webbing, and possibly mechanical components.
4 Release the switch when you have reached the proper position discussed above. Close the switch lid, lock it, and remove the key.
Note: If the cover hesitates or stops before it reaches the end of the pool, you should immediately release the switch and investigate the problem.
Sometimes dirt, debris, or obstacles like towels or hoses can stop the cover. Remove the obstruction and continue covering the pool. If, after
investigation, you cannot find a reason for the hesitation, you should reverse the direction of the cover a foot or two and then retry to uncover the pool.
If the same thing occurs, immediately release the switch and call your SwimWise distributor. Continuing to operate the cover can cause damage not
covered by the manufacturer’s warranty.
Note: For large pools, it may be necessary to loosen the cover mechanism’s torque limiter to close the pool cover.
-!.5!,,9 5.#/6%2).' 4(% 0//,
If there is a loss of electrical power to the system and the cover must be opened for some reason, it can be done manually. This is not easy to do, but it
can be done by following these steps:
1 Remove the cover lid at the non-motor end.
2 )NSERT A v X v ADAPTER ONTO A v RATCHET
3 Insert the ¾” adapter into the end of the cover drive shaft.
4 Ratchet the cover off the pool.
Note: For large pools, it may be necessary to loosen the cover mechanism’s torque limiter to open the pool cover.
4
2
1
Underguide System
3A
3B
Topguide System

8
Maintenance & Care
WATER LEVEL Keep the water level in the pool at the mid-skimmer level. If the pool is overfilled, the water can flow over the lowered bond
beam into the housing and flood the mechanism.
0//, #(%-)3429 We suggest, as all cover manufacturers do, that you only cover pool water that you would swim in. If the water is
temporarily out of balance due to chemical additive, covering the pool will shorten the life of the fabric. Use a good test kit frequently to maintain proper
chemical balance. You must avoid a build-up of chemicals in the pool water that can result in serious damage to pool walls and equipment. Such a
build-up can also create an improper water balance which may cause deterioration of the vinyl cover as well as other cover system components. A
deterioration so caused is not covered by the warranty. After adding any chemicals to your pool, allow the chemicals to circulate before closing the
cover. If you are unsure if it is safe to close the cover, test the water at the surface with your test kit. Some pH adjusters may create harmful levels of
alkalinity (high pH) if not allowed to mix with the water before the cover is closed. The same is true with chlorine shocks. Some chlorine shocks require
as long as 12-24 hours to return to swimmable range. Since safety is often the major reason people purchase a cover, we recommend the use of a
non-chlorine shock. With this type of shock the cover may be closed in 30 minutes or less. Please check with your pool service company for proper us-
age. The use of floating chlorine feeders is not recommended because they vent chlorine gas that can burn the cover fabric and often remain trapped
in the same location.
CLEANING THE COVER When you uncover the pool, the water in the pool is transferred from the pool to the top surface of the cover.
The sun then dries it, causing high concentrations of chlorine on top of the cover that may damage the fabric. You can wash the cover with a mild hand
dish washing liquid as necessary to remove this accumulation. However, do not use laundry detergent or any other chemicals to clean the cover.
COVER GUIDES Retract the cover completely off the pool and clean the cover guide rope and slider channel. Use a high pressure nozzle
on a garden hose to spray directly into the slots of the aluminum deck guides to remove built-up dirt and debris. Repeat as often as necessary to keep
the guides clean. Spray into the pulley housing at the end of the guides at close range to remove debris from within the housing. In windy and dusty
areas with blowing dirt, covers may become inoperable until the debris has been hosed from the guides. In these areas, guides will have to be flushed
clean more frequently. A build-up of sand and/or dirt will grind the webbings causing them to fail prematurely. The webbings used on our covers have
been proven over many years and thousands of covers to last beyond the life of the fabric if the cover guides are kept clean. Premature webbing failure
due to abrasion from debris in the guides is easily preventable and is not covered under the warranty.
HOUSING DRAINS On recessed systems, frequently check the drain(s) to be certain they drain the housing completely and do not allow
water to stay in the housing area. If water is allowed to stand in the mechanism area over periods of time, the system may become damaged by the
constant moisture. Damage to either electrical or mechanical components resulting from standing water or extended submersion is not covered under
the warranty. Clean leaves and debris from the housing as necessary. Run the cover over the pool, prop the housing lid open or remove it, and remove
the debris in the housing. Accumulated debris can hinder the proper operation of the cover or damage the cover material.
-%#(!.)3-  05,,%93 Clean all rotating surfaces and pulleys by spraying with a hose nozzle every 3 months or more often in
sandy or windy areas. Use a hose nozzle to completely wash all surfaces of the mechanism to prevent fine dust or sand from accumulating on the
moving surfaces of the mechanism.

9
Maintenance & Care
PREVENTING RODENT DAMAGE In certain areas, rodents may nest in the cover housing and chew on the cover and ropes.
A common cause of rope breakage is rodent damage, which is not covered under the warranty. Moth balls in a perforated, tamper proof container
placed on a block or brick to keep them dry may help keep rodents under control. Keep poisons out of reach of children.
ADJUSTMENTS AND MINOR REPAIRS Some repairs, such as adjusting the torque limiter or patching holes, are so easy
you can do them yourself. Other repairs are much more complex. We would ordinarily recommend that an owner refers these repairs to his local,
authorized serviceman or organization. Only attempt the adjustments shown in this user guide or at www.coverstar.com.
ADJUSTING THE TORQUE LIMITER If the pool cover will not retract or extend over the pool, it may become necessary to
adjust the torque limiter. This device is designed to prevent damage to the motor or mechanism if there is too much stress on the system due to a
worn-out pulley or other problems. If the torque limiter needs adjustment:
1. To increase motor torque, tighten adjustment bolts with a 9/16 wrench. A wrench is attached to the mechanism for your convenience.
2. How far you tighten or loosen the adjustment bolts will depend on the size of your pool so you should make smaller adjustments in either direction
until the cover operates normally.
WARNING! Never adjust the cover or try to perform any other maintenance while the cover is running. Disconnect the breaker first if you attempt to
service any movable part of the cover system.
PATCHING THE COVER Patch even the smallest holes as soon as they occur with the repair kit provided. Small pin-sized holes can
be patched by applying a drop of glue directly in the hole. Large cuts or tears can be patched using a piece of material cut from the repair kit. Cut a
piece of material that forms a 1” overlap around the tear. Clean and dry the area around the cut or tear. Apply glue to one side of the patch. Apply
glue to the area around the cut or tear that will be covered by the patch. Let the glue set up for one minute. Apply the patch to the cover.
WINTERIZING THE COVER Although during the winter your pool cover requires less attention, water and/or snow will build up on
the cover. If the water level in the pool is not properly maintained, serious damage to the cover can occur. Properly maintaining a pool’s water level
prevents excess stress on the cover that can cause serious damage to the cover system.
'XULQJWKHZLQWHUPRQLWRUWKHSRRO·VZDWHUOHYHODQGPDNHVXUHWKHFRYHUSXPSLVRSHUDWLQJSURSHUO\VRWKDWZDWHURQWRSRIWKHFRYHUGRHVQRW
build up. Even a few inches of water on top of the cover is an enormous weight and can pull the cover and guides into the pool. In situations where
the water level is too low, you should add water to the pool immediately to better support the water or ice that are on the cover. Your cover will
survive any normal winter if these simple precautions are taken.
0DNHVXUH\RXUZDWHULVFKHPLFDOO\EDODQFHGEHIRUHFRYHULQJWKHSRROIRUH[WHQGHGSHULRGVRIWLPH'RXEOHFKHFNWKHZDWHUDIWHUWKHFKHPLFDOV
have had a chance to mix completely. This may require checking the pool water a day or two after chemicals have been added. When covering the
pool for long periods of time, turn down ozone generators and chemical feeders to their lowest level. Constant long-term build up of ozone can dam-
age the fabric. Place the cover pump on the cover to remove melted snow.

10
Symptom Problem Solution
Cover will not move forward or will not reverse A. Circuit breaker or G.F.C.I. is tripped. A. Reset circuit breaker.
B. Water on cover. B. Pump water from cover.
C. Water accumulated between roll-up tube and pool. C. Sweep water off cover.
D. Cover adhering to deck. D. Lift cover and billow air under cover. Use replaceable welcome mat etc.
under cover to break deck adhesion
E.Torque limiter loose. E. Tighten both torque limiter brake bolts until the cover moves.
(See System Diagram, page 11)
F. Motor needs service. F. Call your distributor/dealer for service.
Water leaking onto cover A. Cover caught on something sharp. A. Remove sharp object and use patch kit to repair.
B. Tear caused by foreign object or abrasion pinhole. B. Use patch kit to repair.
Cover retracts out of square A. Rope lengths unequal. A. Re-pin the rope on rope reel so the rope is exactly the same on both sides.
B. Uneven drag on cover as it retracts off pool. B. Some unevenness may be unavoidable due to pool configuration.
Cover not even at end of pool A. Ropes are not the same length. A. Re-pin the rope on the rope reel so the rope is relatively longer or shorter than
the rope on the other side.
Cover seems to be running under stress A. Excess friction during operation. A. Check pulleys to see if they are binding. If they are, clean them. Check and
clean cover guides if necessary.
B. Cover adhering to deck. B. Billow cover by lifting fabric to break adhesion.
C. Debris in housing C. Remove cover lid and clean out debris.
D. Cover too tight. D. Add water to pool or replace cover.
E. Reel brake too tight. E. Loosen reel brake jam nut, reset and tighten jam nut.
F. Tube brake too tight F. Adjust brake by loosening brake nuts/bolts
Installation Check & Trouble Shooting System Diagram
For your satisfaction, please check the following items with your installation representative to help you understand how to operate your cover.
1. Be sure that the installation representative who installed your pool cover has explained the proper operation of the following:
3ODFLQJWKHFRYHUSXPSLQSRVLWLRQZKHQWKHFRYHULVFORVHG
 2SHUDWLRQE\DXWKRUL]HGSHUVRQVRQO\
 3RROFKHPLFDODSSOLFDWLRQDVLWDIIHFWVWKHFRYHU
 3URSHUPDLQWHQDQFHFDUH
2. Did you read the drowning prevention information on the back cover of this user guide?
3. Did a representative offer you assistance on how to maintain a safer pool area?
4. Were you informed of the importance of removing all standing water from your cover for safety and operation?
TROUBLE SHOOTING