Cowboy A1 Operation instructions

A
Guide
for
Riders

I am a Cowboy
Original manual
French version of this manual available at:
https://cowboy.bike/pages/downloads
Dutch version of this manual available at:
https://cowboy.bike/pages/downloads
The product: bicycle with electric pedal
assistance, Model: Cowboy Model A1 is in
compliance with directives 2006/42/EU,
2011/65/EU, 2014/53/EU, 2014/30/EU. To
see the full EC declaration of conformity, visit
https://cowboy.bike/pages/downloads
Cowboy S.A.
67 rue de la Régence
1000 Brussels, Belgium
www.cowboy.bike

And your bike
— 4mm Allen key (small) — 5mm Allen key (large)
— Pedals — Battery Charger
— Pedal Wrench
— Battery Keys
— It’s all in the box.

Get
Started

01. Adjust the handlebar.
Your bike comes with the handlebar parallel to
the wheels and frame.

— Assembling your bike.
Rotate the handlebar
Rotate it clockwise until it is perpendicular to
the wheel and frame.

02. Tighten the handlebar.
Step One
Using the 4mm Allen key (small), tighten the
two lateral screws as shown. Use reasonable
force.
4mm Allen key
(small)
4mm Allen key
(small)

5mm Allen key
(large)
— Assembling your bike.
Step Two
Using the 5mm Allen key (large), tighten the
top screw as shown. Use reasonable force.

5mm Allen key
(large)
03. Fold the brake handles up.
Step One
Using the 5mm Allen key (large), loosen the
screw under each brake handle.
IMPORTANT NOTE:
if the brake hoses touch the frame after doing this operation, then the brake handles should be folded upwards more until it is
no longer the case.

5mm Allen key
(large)
45°
— Assembling your bike.
Step Three
Using the 5mm Allen key (large), tighten the
screw as shown. Use reasonable force.
Step Two
Turn the brake handles up until they point
downwards at a 45º angle.

04. Assemble the pedals.
Right and left pedals are different. You can
recognise them with the stamped R and L
marks on their axle.
Step One
By hand at first, screw in the right pedal in a
clockwise manner.
L R

— Assembling your bike.
Step Two
Finish the job using the pedal wrench. Use
reasonable force.
Step Three
Repeat the operation for the left pedal,
proceeding anti-clockwise this time.

05. Adjust the seat.
The saddle is at the correct height if your
knee is straight when you place your heel on
the pedal and the pedal is in the six o’clock
position.

— Assembling your bike.
Use the 4mm Allen key (small) on the seat lock
to adjust the saddle height, proceeding by
increments until you reach the correct height.
If you don’t feel comfortable with such a
saddle height, lower the saddle to a position
that suits you better.
4mm Allen key (small)
Important note:
Do not raise the saddle above
the insertion depth warning
mark indicated on the seat post.

Get to Know
Your Bike

01. Rear Safety Light
With brake feature, your
visibility increases when
you brake.
CAUTION:
There is a risk of explosion if the battery is replaced with anything else than a genuine Cowboy spare part.
Dispose of used batteries at your local recycling center.
02. A Handy Battery
252Wh (36V). Removable,
light and compact. Gives
up to 50km of freedom.
03. Rear Hub Motor
250W of power. Ride like
you always do but faster.

04. Battery Display
An elegant display keeps you informed of
your battery level at a single glance.
06. Sensors
Our intelligent speed and torque
sensors kick in the motor-assistance
system as you pedal.
05. Front Safety Light
Keeps you going safely when
visibility becomes a higher priority.
07. Battery Charger
Full charge in less
than 2.5 hours.
— Get to know your bike.

Intuitive
Motor Assistance