Iluminarc Ilumiline Logic 24 Optic RGB User manual

www.ILUMINARC.com
[phone]
Ilumiline LΩgic™ 24 Optic RGB
USER MANUAL

Ilumiline LΩgic™ 24 Optic RGB User Manual 2 4/20/2009 7:36 PM
Safety Instructions
Intended only for use with LΩgic™ series devices.
Please keep this User Guide for future consultation. If you sell the unit to another user, be sure that
they also receive this instruction booklet.
Always disconnect from power source before servicing or replacing fuse and be sure to replace with
same fuse type.
Secure fixture to fastening device using a safety chain.
Maximum ambient temperature (Ta) is 104°F (40°C). Do not operate fixture at temperatures higher
than this.
In the event of a serious operating problem, stop using the unit immediately. Never try to repair the
unit by yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please
contact the nearest authorized technical assistance center. Always use the same type spare parts.
Never connect the device to a dimmer pack.
Make sure the power cord is never crimped or damaged.
Never disconnect the power cord by pulling or tugging on the cord.
Avoid direct eye exposure to the light source while it is on.
Caution! There are no user serviceable parts inside the unit. Do not open the housing or
attempt any repairs yourself. In the unlikely event your unit may require service,
please contact ILUMINARC™at: 954-923-3680.
Caution! After prolonged periods of operation, the fixture chassis may reach high
temperatures. Use caution when handling this fixture.
Note! Please refer to local code and regulation for proper installation of this fixture.
Please read these instructions carefully, which includes important
information about the installation, usage and maintenance of this
product.

Ilumiline LΩgic™ 24 Optic RGB User Manual 3 4/20/2009 7:36 PM
LED Life: ILUMINARCTM rates LED lifetime based on lumen depreciation of 70% of the original output, with data
provided by the manufacturer of the LED. Data from the manufacturer of the LED are not independently verified or
measured by ILUMINARCTM. When the fixture is operating in optimal environmental conditions, the LED lifetime is rated
to be 50,000 to 70,000 hours by the LED manufacturer.
LED Binning: LED manufacturers sort LEDs into “bins”, based on variances in color, output intensity and the frequency
at which the semiconductor operates. ILUMINARCTM strives to hold its LED manufacturers to the highest standards of
binning to optimize consistency in output from fixture to fixture. However, the availability of a single bin cannot be
guaranteed. With that in mind, ILUMINARCTM has developed a rigorous control system to seek the best achievable
consistency in color and output.
Color Rendering Index (CRI): CRI is an industry standard method to compare properties of different types of light
sources. There are known limitations and inconsistencies related to CRI. Results may vary depending on the
environmental factors involved. For this reason, the US Department of Energy (DOE) states that CRI should be
considered as one point of reference among others in evaluating white LED products and systems.
The following is an excerpt of recommendations from the DOE:
1. Identify the visual tasks to be performed under the light source. If color fidelity under different light sources is critically
important (for example in a space where color or fabric comparisons are made under both daylight and electric lighting),
CRI values may be a useful metric for rating LED products.
2. CRI may be compared only for light sources of equal CCT. This applies to all light sources, not only to LEDs. Also,
differences in CRI values of less than five points are not significant, e.g., light sources with 80 and 84 CRI are essentially
the same.
3. If color appearance is more important than color fidelity, do not exclude white light LEDs solely on the basis of
relatively low CRI values. Some LED products with CRIs as low as 25 still produce visually pleasing white light.
4. Evaluate LED systems in person and, if possible, on-site when color fidelity or color appearance are important issues.
Source: DOE publication: PNNL-SA-56891, January 2008
Dimensions

Ilumiline LΩgic™ 24 Optic RGB User Manual 4 4/20/2009 7:36 PM
Technical Specifications
WEIGHT & DIMENSIONS
Length (of fixture)..................................................................................31.5 in (800 mm)
Length (including the cable strain relief).................................................... 2.2 in (57 mm)
Diameter..................................................................................................... 3 in (75 mm)
Weight ......................................................................................................3 lbs (1.35 kg)
LIGHT SOURCE
LED ........................................24 x 1W 350mA (6 red, 6 green, 6 blue) LED’s 50,000hrs
ELECTRICAL SPECIFICATIONS
Input current.............................................................................................350mA @ 48V
Power consumption...............................................................................................25.6W
POWER/DATA CONNECTION
Power/data input....................................................................................................RJ-45
Power/data cable ...............................................................Belden 1585A Plenum Rated
EXTENDED INFORMATION
Construction...................................................................................... extruded aluminum
Power/data cable ...............................................................Belden 1585A Plenum Rated
WARRANTY INFORMATION
Warranty......................................................................................2-year limited warranty
COMPATIBLE DRIVER
LΩgic™ 4X36..................................................................................................34X36001
ORDERING DETAILS
Ilumiline LΩgic™ 24 Optic 25x6 RGB.............................................................. 22024001
Power Link Out
LED patch cable: for linking from LΩgic™ 4x36 to supported LED fixtures
ILUMINARC™ recommends Belden 1585A plenum rated cable.