Craftsman CMXGZAM241032 User manual

769-21170
ASSEMBLY INSTRUCTIONS
DELUXE SNOW CAB
_
INSTRUCCIONES DE MONTAJE
CABINA DE LUJO PARA MÁQUINA QUITANIEVES
_
INSTRUCTIONS D’ASSEMBLAGE
CABINE DE LUXE POUR SOUFFLEUSE À NEIGE
ASSEMBLY INSTRUCTIONS PAGES 2-8
INSTRUCCIONES DE MONTAJE PÁGINAS 9-15
INSTRUCTIONS D’ASSEMBLAGE PAGES 16-22
WARNING: Cancer and Reproductive Harm
ADVERTENCIA: Cáncer y Daño Reproductivo
AVERTISSEMENT : Cancer et effet nocif sur la reproduction
www.P65Warnings.ca.gov
CMXGZAM241032

649-05003
(Qty. 2)
B
2
PARTS IDENTIFICATION PAGE
5/16"-18 x 1.75" Hex Bolt (Qty. 16) 5/16"-18 Hex Nut
(Qty. 16)
1/4"-20 x 0.50"
Hex Bolt (Qty. 2)
1/4"-20 x 0.375"
Socket Hex Set Screw –
Locking (Qty. 12)
5/16" Lock Washer
(Qty. 16)
710-0909A 710-04468 712-0267 710-1842A 736-0119
789-00070689-00194689-00195
S TRP
N
649-05002
(Qty. 2)
Set Screw (S)
Set Screw (S)
A
749-05014
(Qty. 2)
F
649-04114
(Qty. 2)
G
649-04113
(Qty. 1)
Set Screw (S)
C
K
(Qty. 2)
L
(Qty. 2)
M
(Qty. 4)
689-00303
H
(Qty. 4)
689-00302
I
(Qty. 1)
649-04117
(Qty. 1)
Set Screw (S)
J
749-04896
(Qty. 2)
Set Screw (S)
D
(Qty. 1)
COVER POUCH (Qty. 1)
790-02277 790-00481
Hardware Included: Hardware shown is actual size. Note: Your kit may have excess hardware.

3
ASSEMBLY INSTRUCTIONS:
1. LaysetsofbarsAandBonaatsurface.SlideAandBallthewaytogether.
Insertsetscrew(S)intotheendofbarB,securingnger-tight.Repeatwith
othersetofbarsAandB.
NOTE:Donottightensetscrew(S)usingAllenwrenchuntilentireframeis
assembled.
3. InsertpolesF,narrowendup,intotheunionofbarsJ,A/B.
2. AttachbarJtotheBendoftheA/Bassemblies(seearrows).Insertset
screws(S)intobarJ,securinginnger-tight.
Refer to parts identication sheet to ensure you have all necessary parts.
A B
S
B
BJ
F
F
B
B
A
A
A
A
S
J
CAUTION: WEARING SAFETY GLASSES IS RECOMMENDED DURING ASSEMBLY.
Assistancefromanotherpersonisrecommendedforcertainsteps.
Narrow end up
Notice orientation of bar B
Set Screw (S)
S
BOX WRENCH
LLAVE DE CAJA
CLÉ FERMÉE
ALLEN
WRENCH (INCLUDED)
LLAVE ALLEN (INCLUIDA)
CLÉ ALLEN
(COMPRISE)
SAFETY GLASSES
GAFAS DE SEGURIDAD
LUNETTES DE PROTECTION
3/8"•1/2"•9/16"

4
4. InsertpolesG,narrowendup,intoAendofbothA/Bassemblies.Insertset
screw(S)intotopofbarsA,securinginnger-tight. Front
Back
5. PlacecurvedbarConatsurface,nutsfacingup.
InsertthelabeledendofcurvedbarDintoC(makingsurearrowsmeet).
RepeatwiththeotherbarDontheoppositeendofbarC.Insertsetscrew
(S)intoendsofbarsC,securinginnger-tight.
7. Makesurecabframeisintheshapeofabox,withrightangles(90°).Then
tightenallthesetscrews(S),exceptthesetscrews(S)onthecrossbar
(J),usingtheenclosedAllenwrench.
CAUTION:Donotovertightenthesetscrews.
6. PlaceassemblyD/C/DontoendsofpolesG.Insert
setscrew(S)attopofpolesG,securinginnger-tight.
B
D
DD
E
D
G
J
G
G
S
S
F
C
C
F
F
B
B
A
G
A
B
F
Front
Back
90º
90º

5
Front
Back
DD
Insertexiblerod
assemblyhere
C
I
H
H
Front
Back
A
10. Pullthecabmaterialdownandbacktowardsthearchassembly,D/C/D.
Fastenhook-and-loopstrapsonbothsidesoftheD/C/Dassembly.Slide
elasticloopsovertherearcornerofbarAonbothsides.Fastenhook-and-
loop straps around all bars at various locations. (For your convenience
youmaywanttowaituntilthecabismountedonyoursnowblowerto
finishfasteningthesestraps.)Afterthematerialissecuredovertheframe
assembly,removebarJ.
9. SlidethetworemainingHrodsoverthepreviouslyinsertedHrods.TakerodIand
inserttheendsoftheHrodsintothesteelcollarendsofrodI.Pullthecoverupover
therodassemblyandslidethetopoftherodassemblyintothelargefabricpocket
insidethecover.Thiswillrequiresomebendingoftherods.
8. Pullthecoveroutofboxandlocatetheinsidesleeves.InsertthesteelcollarendsoftheseHrods
intothetopsofpolesF.Thecoverwillbehanginglooselyontherod/poleassembly.FeedoneH
rodthroughonesleeveofthecover,then
repeatwithanotherHrodontheotherside.
NOTE:YoushouldhavefourHrodsandoneIrod.
NOTE:FlexibleHrodswillfeelloosewhen
inserted.Thisiscorrect.Donot
attempttoforceexibleHrods
furtherintopolesF.
Steel Collar
I
Large Fabric Pocket
A
H
F
Sleeve
Steel Collar
H
H
H
H
H
F
F
HH
H
H
I
NOTE:Forsteps8,9and10,pleasebesureyouwearsafetyglasses.
D
D
J
C
SAFETY GLASSES
GAFAS DE SEGURIDAD
LUNETTES DE PROTECTION

11. Your clamps can be partially pre-assembled.
Theclampassemblythatmountstoyourunitmaybe
orientedhorizontallyorvertically.
 Thepreferredorientationoftheclampassemblyistohavethesaddles
perpendiculartooneanother.ThreadthesmallboltPintothecenterof
KandLassemblies,nger-tight.Slidesmallertube,L,intolargertube,K.
12. Todeterminethegenerallocationanddirectionforthecrossbar(J),have
anassistantholdthecabatthedesiredlocationovertheunit.
NOTE:Dependingonyourunit,thecrossbarmaybe
positionedfacingforwardorbackward,andabove
or below any linkage.
13. Noticehowcrossbarwillsitinclampassembliesonceclampsaremounted
on unit.
NOTE:Ifthecontrolsonyoursnowblowerrequiremorespaceforproper
operation,ipbarJ.
14. Holdingcrossbar(J)indesiredlocation,selectareatomountKandLclamp
assemblies. See Fig. 12.
NOTE:Brute®andJohnDeere®unitsmayrequireyoutomounttothe
horizontalhandlebarsontheunit.
NOTE:Preferredpositionisontheverticalportionoftheunit’supper
handlebars.
OR
Lower Handle Bars
(Horizontal Tube Mount) Upper Handle Bars
(Vertical Tube Mount)
Upper Vertical
Handle Bars Lower Horizontal
Handle Bar
L
LL
J
J
L
K
K
K
K
L
P
L
K
K
Forward
Facing
Backward
Facing
Crossbar (J)
OR
OR
6

7
15. Takepre-assembledK,LandMclampassemblies.MountassembliesKandL
inthedeterminedlocationonunit.UseplatesMandlargeboltsN,lock
washerTandnutsRtosecureK,LandMassembliestounit.Nowtighten
smallboltPsobothclampassembliesextendequaldistancefromframe.
NOTE:LocationoflockwasherTshouldbeunderneathnutR.
NOTE:Ifyoursnowblowerisequippedwiththeelectricjoystick,mount
theclamps(L)and(K)tothehorizontalhandlebar.Besuretomount
theseontheoppositesideofthechutecontrolrod.
16. Place crossbar (J) against assembly K and L. Center crossbar (J) against
unit.UsetworemainingMplates,largeboltsN,lockwasherTandnutsR
to secure crossbar. See Figure 15A.
Upper Vertical
Handle Bars
Lower Horizontal
Handle Bar
J
M
M
M
L
K
K and L
P
M
R
N
N
T
T
L
Fig. A

17. Fullyinserttheendsofthefrontofthecabassemblyintotheendsofthe
crossbar(J).Insertsetscrews(S)intoendsofcrossbar(J).Withassistant
holdingcabassemblyhorizontaltotheground,tightenallboltsand
set screws.
CAUTION:Donotovertightenthesetscrews.
18. Finishassemblybyfasteningallhook-and-loopstrapsinsidethecabif
youhavenotalreadydoneso.
CAUTION:Nocabfabricshouldbeallowedtotouchengineorexhaust.
19. Thecabisdesignedtoaccommodatesnowblowersequippedwitha
light.Azipperonthefrontofthecabcanbeopenedandtheappulled
backtoallowthelighttoshinethrough.Atthistime,adjustmentsmaybe
necessary for free movement of operation controls.
20.Forstorage,loosenthetwosetscrews(S)incrossbar"J"andpullthecabupandoutofcrossbar"J."SeeFigure17.
21. Forcleaning,justusemildsoapandwater.
J
S
8

649-05003
(Cant.:2)
B
PÁGINA DE IDENTIFICACIÓN DE PIEZAS
Perno hexagonal, 5/16"-18 x 1.75" (Cant.: 16) Tuerca hexagonal,
5/16"-18 (Cant.: 16)
Perno hexagonal,
1/4"-20 x 0.50" (Cant.: 2)
Tornillo prisionero de
jación, cabeza hueca
hexagonal, 1/4"-20 x
0.375" (Cant.: 12)
Arandela de presión,
5/16" (Cant.: 16)
710-0909A 710-04468 712-0267 710-1842A 736-0119
789-00070689-00194689-00195
S TRP
N
649-05002
(Cant.:2)
Tornillo de jación (S)
Tornillo de jación (S)
A
749-05014
(Cant.:2)
F
649-04114
(Cant.:2)
G
649-04113
(Cant.:1)
Tornillo de jación (S)
C
K
(Cant.: 2)
L
(Cant.: 2)
M
(Cant.: 4)
689-00303
H
(Cant.:4)
689-00302
I
(Cant.:1)
649-04117
(Cant.:1)
Tornillo de jación (S)
J
749-04896
(Cant.:2)
Tornillo de jación (S)
D
(Cant.: 1)
CUBIERTA BOLSA (Cant.: 1)
790-02277 790-00481
Accesorios de montaje incluidos: Los accesorios de montaje se muestran en tamaño real. Nota: Su kit puede tener accesorios de montaje en exceso.
9

10
INSTRUCCIONES DE MONTAJE:
1. ColoquelosconjuntosdebarrasAyBsobreunasupercieplana.ColoqueAyB
juntosentodasuextensión.Introduzcaeltornillodeajuste(S)enelextremo
delabarrayapriételoconlafuerzadelamano.Repitaconelotroconjuntode
barras A y B.
NOTA:Noaprieteeltornillodeajuste(S)conlallaveAllenhastaqueesté
montado todo el bastidor.
3. InsertelospilaresF,conelextremoangostohaciaarriba,enlauniónde
lasbarrasJyA/B.
2. FijelabarraJalextremoBdelosconjuntosA/B(vealasechas).Insertelos
tornillosdejación(S)enlabarraJyapriételosconlafuerzadelamano.
Consulte la hoja de identicación de piezas para asegurarse de tener
todas las piezas necesarias.
A B
S
B
BJ
F
F
B
B
A
A
A
A
S
J
CUIDADO: SE RECOMIENDA USAR GAFAS DE SEGURIDAD DURANTE EL
MONTAJE. Se recomienda contar con la ayuda de otra persona para
algunos pasos.
Extremo angosto
hacia arriba
Observe la orientación de la barra B
Tornillo de
jación (S)
S
BOX WRENCH
LLAVE DE CAJA
CLÉ FERMÉE
ALLEN
WRENCH (INCLUDED)
LLAVE ALLEN (INCLUIDA)
CLÉ ALLEN
(COMPRISE)
SAFETY GLASSES
GAFAS DE SEGURIDAD
LUNETTES DE PROTECTION
3/8"•1/2"•9/16"
9.5 mm•12.7mm•14.3mm